Whenever I manually pull my gear selector into first gear it blows one of the 10a fuses (not sure which number). I lose all gauges and accelerator pedal. It's about the fourth fuse from the right on the bottom row.
View 4 RepliesThe other day I had a metal pin fall out from under my dash and hit me on the foot (only reason I would have know if fell out till I clean the truck)
Ever since then the gear selector handle for my transmission has become sloppy and when I go to turn off the truck, I have to hold the arm up to turn key off all the way. I have looked to try and find where it goes and cannot find the location. I have also looked at a blown up parts diagram and cannot find it. Where it goes?
2002 F250 SD V10 with auto...
I have a 1999 ford f250 5.4 2 wheel drive i believe its a 4r100 transmission. auto. I have reverse but no forward gears. Ive heard this is a common problem , and on my reverse it has to hit 3000 rpm before it even tries to move and D 1 2 i have nothing only thing i hear is the engine sound changes gets deeper. Do i need a whole new transmission or is this fixable.
View 4 RepliesI have an 01 f250 5.4l standard. #19 fuse keeps blowing. I hAve taken the gauge cluster out and do not see any wires melted or burned. It blows the fuse as soon as I turn the key over. I have read things saying the overdrive but that doesn't work with mine.
View 4 RepliesI have 2005 F250 6.0 XLT. I was driving the other night and all of a sudden my dash lights went out. I noticed I was being flashed from other drivers and discovered that my parking lights are not working. A preliminary check of fuses I discovered fuse #17 (15a mini) was blown. I installed and new one and upon turning my lights on, the fuse popped again. My headlights and turn signals work properly. It appears I have a wire shorted to ground somewhere on this circuit.
The truck is completely stock with the exception of an aftermarket radio which I installed two years ago.
I checked all the fuses with my test light and they are all correct (both sides of each fuse). I disconnected the gray connector and black connector in the driver side rear of the truck to isolate the issue. New fuse pops as soon as I turn lights on. I completely removed the tail lights, trailer 7 pin connector , completely removed both headlights. I did not disconnect the roof running lights or the mirror lights. I am completely stumped.
Just bought a used 15 F-250 with 57,000 miles, yesterday tried to start it and nothing happened. Checked the starter fuse and it was blown, replaced it and it immediately blew when i tried to start the truck. Pulled the starter and had it tested and it was good, replaced the relay and still blowing fuses. I have got it to start a couple of times but as soon as you kill the engine and try to restart it blows the fuse. What was the fix? Truck had no problems trying to start before this problem started.....
View 7 Replies2004 5.4L F-250 ... it's a one owner truck I bought brand new in 2003 and only has 50,000 miles on it.
I have the 2V 5.4 engine no tuner or chip. 4x4 with 4" lift and 35's and I changed the rear to 4.88's. I love the truck but my problem is when I hit a large bump or drive too fast on a dirt road the fuse#23 that controls the PCM will blow. Consistently. I have to keep a box of 20 amp fuses handy. I have a 2 post lift in my shop and have scoured over every wire that is connected to the fuse. The EVAP solenoid, AC Clutch, Transmission solenoids and the O2 sensors. I only have 2 sensors I could find one on each side of the headers.
I couldn't find any rubbing wires or exposed wires. I am at a loss. It only happens when I hit a large bump. Could it be the Torque Converter Clutch Solenoid?
My brother in law is a mechanic and he brought over the diagnostic computer and when it blew while hooked up he seemed to think it was the TCC solenoid because when it engages the chart shows it angling up but when it disengages it drops off straight like it should. My truck seems to run fine when the fuse isn't blown, but when it blows it goes into a limp mode with the tranny stuck in 3rd or 4th gear and I have to drive it home in 1st.
My wifes truck is having some issues right now. Last week I was driving it down the highway, and the gauges all went off, the door buzzer was sounding, and the door locks where going up and down constant when I had my foot off the gas pedal. Found the fuse and fixed it with a replacement, but its down it three times all together since then?
View 9 RepliesThe fuel pump fuse keeps blowing intermittently. I would assume it's a wire grounding out somewhere but I can't seem to find one yet. I do have a faulty purge solenoid on the canister but I don't think that would cause this. The reset switch doesn't seem to be tripped either.
View 3 RepliesI recently purchased a 04 f250 with the 6.0l powerstroke. I drove it for about 3 weeks now, Ive put my trailer behind it with small loads and just today tried to use the tow/haul button. When you go to pull out the tranny never shifts from first gear?? Its pulls and runs fine until you push the buttan and no shifting........
View 6 RepliesI'm looking at purchasing a 2003 F-350 from a Ford Dealer, Drove the Vehicle last night and the Gear shiftier was very tight and hard to pull down. Is this a real concern? The Sales guys said its better to be stiff rather than sloppy. But they will say anything, right. The vehicle is a deal and so I'm looking to find out why.
View 1 RepliesI have a 99 f250 with some procomp (325s) that are 12.5 wide with a 6in lift my superchip tuner can change the trannys shift points but I am pretty sure a new gear ratio is needed. I dont do a whole lot of off roading with it its mainly my driving around and highway rig whats a good gear ratio that would work for me
View 9 RepliesI have an isspro sensor that I need to install on my 4r100. I have it all installed except for the actual sending unit. My question is where is the best place to put it?
I've watched multiple YouTube videos and it seems a lot of people use the test port on the driver side above the linkage. I found out the hard way that it is a very poor choice of location. A lot of people say that the best way is to drop the pan drill a hole and weld in the bung? I was wondering would it be possible to put it on the "out" line on the transmission oil headed to the cooler? 01 f-350 7.3
I have a 2014 f250 with the 6.2 and just turned 13,800 miles. I tend to drive in tow haul a lot, while not towing because I like the shift pattern better and saves on brakes while stopping. Last night I slowed to a stop sign, came to complete stop. Went to take off slowly like always and the truck was like in neutral, looked down and the indicator showed 5th gear. Let off and watched it go to 1st and took off no problem. This all took only half a second or so, seemed fine after that. What might of happened?
View 3 RepliesMy daughter has this truck and I was driving it the other day I noticed it misfiring when the trans shifts down under a slight pull and/or going up hills. It looses power and speed when this happens but if you back off, it smooths out when it shifts into overdrive. I haven't had it to a mechanic to check any codes yet.
View 3 RepliesThe other day I was driving i was driving down the road when suddenly my truck wouldn't shift out of first gear, then the truck died and the motor wont turn over either. Acts like it is locked up. Its an 01 with v10 and 4r100.
View 6 RepliesMy 2000 f250 7.3 4x4 with a 4r100 tranny. I was towing my boat home and noticed the temperature rising from roughly 140 all the way to 160 over a short distance. As soon as I pulled up to the house I noticed I was dumping my transmission fluid. Went to a mechanic and he fixed the leaking on the transmission by replacing some seals and changed out my rear main seal while the tranny was out.
I also went ahead and replaced the torque converter so I would not have to do it in the future. went to pick up my truck and noticed that on the way home the temperature was still rising. On a normal day here in Texas my tranny temperature was about 125 While towing it would creep up to about 143. Now, just getting home it got up to 180. What could be causing the temp to run this high and keep climbing?
What's an acceptable GVW value when one is looking to replace the air to oil cooler for this transmission?
2001 F250 CC SB PSD 7.3 Edge
On my previous 1992 F-350, when I serviced the E40D 2WD trans I replaced the filter during a trans service. I read about some filters falling down inside pan causing shifting issues. There is an aftermarket clip sold that holds the filter in the up position and prevents it from falling into pan.
Is the clip also used on the 2WD 4R100? is it the same issue of potentially falling down in pan as was the case with the E40D? Preparing to service my 2003 F-350 2WD 4R100 and install a new filter and want to be sure I have all parts/supplies ready to go.
I have an 01 f250 with a 4r100. Trans has not been slipping at all and yesterday it started a rough shift between 1st and 2nd. (3-4K Rpms) At the same time 4th gear stopped engaging. Shifts out of 3rd but does not go into 4th. I can hit my od button and it will shift back into 3rd and start pulling. Still no slipping just doesn't want to change 1-2 or engage 4th. I have done a full trans fluid change including new filter and tc. Old fluid looked fine with no metal flakes or garbage in it. So all new fluid still same problem. I was thinking of changing my shift solenoid.
View 9 RepliesRecently got a 2003 f 250 6.0 that has had a little work done on it. Absolutely love it with 1 exception. When I turn on the ac or heat It blows a 10 amp fuse that goes to the blower relay. It was occasionally now it's all the time.Blower ok, fan speed resistor ok. What or where to look.
View 8 Replies