Ford Super Duty (1999-2016) :: 2002 - Vibration In Driveline Faintly Starting At About 45 MPH
Jun 16, 2017
02 CCSB, and I have a vibration in my driveline that's starting to drive me nuts on my commute every day. I can feel it faintly starting at about 45 mph, whether the torque converter is locked or unlocked. The vibration peaks at about 60 mph and goes away at about 65+. My u-joints are all moog and grease them every oil change (about 120k on them now). At this point I suspect the carrier bearing, yokes, or even u joints but there's not much play. However the rubber around the carrier bearing is in rough shape and dry rotting. I'm curious if there's a test I can do to find the culprit.
View 1 Replies
Advertisement
I have a 15 F250 CC SB 6.2 4x4 that is suffering from a driveline vibration. Had the shaft checked for balance and it was off. It's a little better now but still there. Checked all the angles and they're correct. Also came up with a curious observation that all CC SB 4x4's have a slip yoke driveshaft at the transfer case while all the other trucks have the fixed yoke. This appears to be my source of the vibration.
View 3 Replies
I have a 1999 f250 SuperDuty with a nasty vibration That begins at about 70mph. The truck is an extended cab 5.4l Manual trans 4X4 with a one piece driveshaft (No mid bearing). The Vibration appears to me to be a driveline vibration that is speed dependent. It is the same in gear, out of gear clutch in or out. I have replaced the wheel bearings/hub assemblies on all four corners, completely rebuilt and balanced the driveshaft the driveshaft, removed the front driveshaft, put brand new tires mounted and balanced on all four corners, new clutch, had the flywheel turned and balanced, and replaced the transfer case output bearings. Pinion bearing feels tight and does not leak.
Also the Input in the trans felt tight when i had the trans out. The truck had the vibration when i bought the truck and still vibrates after i have done all of this work. i did not change the motor mounts because they looked fine. when i bought the truck the tabs on the extension housing holding the trans-mount to the trans were broken so i make a huge "exhaust clamp" to straddle the trans and bolt to the trans mount.
After driving the truck up north last weekend the truck seems to shake going taking of at lower rpm as if the motor mounts and trans mounts are bad. I guess my questions is can a bad trans mount, motor mounts cause this Vibration at highway speed. if so is there a way to fasten the trans-mount to the extension housing without replacing the extension housing. If not what else can cause this issue?
View 7 Replies
I recently replaced my Ford Factory clutch with a new LUK kit, lever, pivot & hydraulics and I have to say it is absolutely perfect. If you are going to take the time to do the clutch, do it all. While we had it apart, I decided to push up my Up-Pipe replacement and do it while the transmission is out. What takes several hours to do is done in 30 mins this way. As we all know when we start in a job, we see other things and say well while it is apart I may as well do this, and do that. I decided to do the U-joints in the rear shaft. I had marked the shafts prior to removal for orientation but my assistant did not mark all 3 U-joint knuckles when he changed the joints and reinstalled the shaft.
I took the truck out for a drive and starting at about 15 MPH all the way to 60 ( I dared no faster) it was making me nauseous. Today I looked into it, marked current locations and started rotating front and rear joint 180 to no avail. I said lets just rotate the center joint and go from there. as I was pulling the carrier i noticed a HUGE but dull yellow arrow on the short shaft. I decided to look at the rear shaft and found a HUGE but dull yellow arrow 180 degs from the front. It looks like it could have been a factory mark. I repressed the center u-joint so the 2 arrows line up and the vibration went away. I can not express the aggravation this could have caused if not for those arrows. Take the time to properly index the drive shafts, it will save you tons of time and agitation.
View 1 Replies
I have begun to notice a vibration when I am in first gear starting out with a bit of a load. The vibration goes away as I gain speed and the load reduces. None at any of the higher gears. If I take off real easy and allow the truck to gain speed without pushing it, the vibration does not exist. The truck is the one outlined in my signature. It is equipped with a 3 speed auto with overdrive. I am thinking this could be a U-Joint that might be starting to go out.
View 9 Replies
I have a vibration starting at 60mph. Its slight but there. I crawled under and found a very shiny rectangle of metal. Safe to assume I flung a shaft weight? It drives perfect around town just at freeway speeds.
View 14 Replies
I just bought my 2015 F350 long bed Platinum a month ago, and the first trip with my 12,000 lb. 5th wheel had a vibration when starting out, but only from a stoplight with some acceleration or an incline, not at level slow startup.
View 6 Replies
When I'm in 4 high and I coast I can hear something from the front drive line. It's a soft whirring/grinding type noise.
If I'm accelerating there is no sound . Only when the driveline forces reverse and the engine starts to slow the truck do I hear something.
With my hubs locked but in 2wd I don't hear anything.
Is this something to be concerned about or is it regular noise?
We have had a brutal winter so I've been in 4x4 75% of the time.
View 1 Replies
My 02 ford V10 is hard starting. If I start it every day, it will start and run well. If I let it sit longer than one day I need to spray some starting fluid to get it to run. I turn the key on and let it pump up before I try to start it. After it starts with starting fluid, and runs for a minute or so it will start up with no problem.
View 14 Replies
I bought my 2012 F250 CC SB 6.2 back in December and really haven't had the truck in 4x4. Today we got a bit of snow. The roads were slippery so I engaged the 4x4 ESOF while at a stop sign (I know, didn't have to be stopped but I was so I put it in 4x4) The driveline was noticeably louder.
I had a relatively constant hum that almost reminded me of a wheel bearing going bad. If you've ever experienced a wheel bearing going bad the sound gets louder as you go faster. I'm sure it's not a wheel bearing since it only makes the sound in 4x4.
It's a fairly annoying sound and is louder than my old 99 F350. Notice the driveline being significantly louder in 4x4? There are no driving issues just a louder sound than what I was used to. I have the full Ford Certified warranty and can bring it in but I thought I'd run it by the brain trust here to get thoughts before going to the dealer.
View 10 Replies
I took my truck in for a clunking noise in the driveline as I come to a stop and sometimes when shift into park. It is now the 7th and I'm told parts have been ordered and the truck will be worked on when parts come in. I asked to speak to general manager and still no call back. I called customer relations and nothing they can do.
Honestly I think the have me on the back burner since I'm warranty work opposed to marked up repairs. Am I being unreasonable on my expectations of repair time? I called around and a ring and pinion job is quoted at 3 days at the most. Other repairs have been approved as well and parts are in for those, but they have not actually repaired them either.
View 14 Replies
So, I'm slowly but surely eliminating a terribly shaky front end on my 2002 F-250 7.3L 4x4. First was a new carrier joint on the front drive shaft. Didn't work much, but the shop said the darn thing was falling apart. Next thing I did was new wheel bearings and manual hubs. Less vibration for sure. But the last remaining issue, in terms of vibration, is that when I let go of the Accelerator going at any speed above 60 MPH, it makes a horrible horrible noise, and I could feel a vibration. It shakes the whole truck, but I can very noticeably feel it directly in the gas pedal. It's really only an issue during deceleration. What could it be??? Drive shaft U-joints? Torque Converter? Something else in the Front End? Something in the engine even?? I don't exactly have the funds to tackle every possible solution.
View 1 Replies
Need to diagnose my truck issues. On my 2002 F250 V10, when I try to start it, the engine just cranks and cranks and cranks with no fire or even hint if starting. I am not sure if it has no spark or isn't getting any fuel. I just replaced all ten spark plugs and coils less than 500 miles ago. I want to perform the fix myself, but I need to get the problem diagnose the issue first.
View 8 Replies
2002 F350 5.4 . I did some plowing today, truck ran Great, but noticed the Auto Shifter starting to get some play in it, 185 k on it. I recall reading about how to tighten it back up.
View 3 Replies
I've got a 02 SD v10 4x4 with Warn hubs and 97k. Bought it a couple months ago and I've noticed a vibration coming from the front driver side. Symptoms are that of a bad wheel bearing; vibration that increases with speed and not RPM, seems to lessen on left handed turns (weight transfers from driver side to passenger side) and gets worse on right turns. Also the truck seems very twitchy and hard to keep straight on the highway.
Snowed the other day so I locked in my warns (just in case) and I instantly noticed the noise and vibration almost went away entirely except for on the freeway around 70+ mph. Also noticed it seems less "Twitchy" on the freeway. Mind you the hubs are locked in but still in 2wd. After doing a little bit of reading some were saying this is a sign of bad needle bearings and not the entire hub.
I haven't jacked up the tire and checked typical movement in a bad wheel bearing. I know my way around vehicles and 4x4's pretty well...
View 3 Replies
I have a 02' 250 4x4 with 250000 miles on it. While driving between 55 to 65 mph there is a roar and vibration that seems to be coming from the rear. I have about 35% tire tread left and have had the rear tires balanced and it still does it. Having issues with drive shafts unbalanced or rear ends?? I am not sure where to start....
View 1 Replies
2002 Ford F250 4x4 Superduty Lariat (4 door). Just changed the locking hubs to a new set of Warn manuals. I began to periodically hear what sounds like a rumbling/bearingish/howling kinda sound. Happens when you hit a bump at any speed...then howls till you hit another bump..goes away..then process repeats. Come to a complete stop, and the sound usually goes away till you hit another bump. The hubs are "free" at this time.
Heres the weird thing...when the noise starts...I switch it into 4 wheel drive on the dash...the sound instantly goes away. Click it back outta 4 wheel drive (hubs are still unlocked this whole time) and the sound is gone. drive some more down the road, maybe hit a slight bump, and the sound returns. Switch it back into 4x4...sound instantly goes away. Its not really in 4 wheel drive, cause the hubs aren't locked in...but that cures it till I take it back out. What could be causing this howling ? Its getting worse, and you can feel a slight vibration in the floor now when its doing it.
View 8 Replies
Truck is an '07 F350 Supercrew, 8ft bed, SRW, 2wd. I bought the truck last month and noticed a low frequency driveline vibration starting at about 45 mph and is noticeable to about 65 mph. Feels like a bad u-joint. So I pulled the drive shaft (two piece) and checked the joints. They seemed find so I sent it to a commercial truck shop that does driveshaft work. Had the joints replaced and the shaft rebalanced.
Re-installed drive shaft and went for a test drive. No real change in the vibration. The hangar bearing seemed fine so it wasn't changed. Doesn't feel like a wheel out of balance. My experience tells me its a drive shaft.
View 8 Replies
Ive got a 2002 f250 Sd 4x4 with 93000. Im getting severe vibration from the front drivers side at highway speed. I thought it might be a warped rotor but i cant feel it in the brake pedal, when I put the brakes on. How can you tell when the hub bearing assembly is going bad? The truck doesnt pull to that side either. I can hear it, and feel it more when i'm going around highway corners. When im driving through town, I can hear a "clunk,clunk,clunk" noise coming from that side also.
View 14 Replies
I work for the transportation department at a school and we have a bunch of 6.0 f350/450 busses and this bus I am working on has a no crank condition. Bus in question is a 2006 F450 6.0.
Currently if you turn the key to start the engine the solenoid just clicks but the engine wont crank. The person working on it before me assumed that the batteries and or starter were bad so they were replaced(0 miles on them right now) but the problem still persists.
First thing I did when I started working on this bus was jumping the starter relay and the starter engages and starts the engine perfectly. That being said I know the starter wiring is fine.
Secondly I looked through the wiring diagrams and saw that the PCM grounds the 85 terminal on the starter relay so I tried grounding the 85 and I was able to crank the engine with the key so that was telling me that the actual starter relay is fine. Next I went and swapped the PCM with another 2006 f450 thinking maybe the grounding switch in the PCM was bad and I have the same no crank condition. The PCM from the bus in question was swapped to the doner bus and it cranked perfectly(PCM in question is fine).
Next thing I did was look up all of the ground locations for the PCM or anything to do with the starter and they were all cleaned and still have the same no crank.
Looking around on the internet I see that the viscous fan can cause a problem if it shorts out so I unplugged that and no change in the no crank. I also saw that the trans range sensor could cause a no crank condition but I am getting back up lights/beeper and the bus "wants" to crank so I am thinking that the TRS is not the problem.
Lastly I tried hooking my Modis scanner up to this bus and was NOT able to communicate with either of the PCM's I tried. Not sure if this is related to my no crank condition. I checked all of the wiring that I could but could not find any chafing or breaks in any of the OBDII wiring. My planned next step is to replace the TRS...
View 10 Replies
I was wondering if there is a aftermarket product to give my truck a more Rumble when starting and idling.
View 8 Replies
