Ford Super Duty (1999-2016) :: 2002 V10 Won't Stay Running / Loss Of Power And Slight Miss
Jul 4, 2017
This last April I was towing my trailer back from camping approx 125 miles when I detected a loss of power and a slight miss. I managed to make it home. It wasn't until I made it home that the engine finally started coding. Miss on start, a couple of cylinders missing and output shaft speed sensor circuit failure. So naturally, I decided to do what I felt needed done anyways, change all coils and plugs. Oddly the problem got worse to the point where I almost didn't make it home after test driving it, it kept stalling out and was difficult to keep running.
After some research and advice from others, I started replacing some components; MAF sensor,IAC valve, output shaft speed sensor. Nothing. In fact now the truck wont move, I start it up it idles a little rough, but then I put it into gear and with in seconds she shuts her self down. I've replaced the fuel filter, checked the fuel pressure and it is in specs. I've now had it towed to two mechanics neither of which have any solution. They've put expensive computers up to it and still nothing. I really do not know what to do at this point. Lastly the only code that continues to come up is P0720, output shaft speed sensor circuit failure, I really miss my truck!
View 9 Replies
Advertisement
I Have a 2002 F 250 That I recently changed the fuel pump. and now I'm having a tail light problem. when i start the truck, my tail lights and plate lights comes on (dim). if i turn my head lights on the truck stalls out. if i step on the brake or put the truck in reverse it stalls out. if i put it in drive it runs just fine. i checked my fuses and relays and the problem is still there even when the relay and fuse for the lights are out. when i turn the truck off all the light go out.
can't seem to find any info on this problem anywhere.
View 3 Replies
I just purchased a 2003 F250 Super Duty with the 6.8L V10 It has really high miles on it as it was a landscaping companies fleet truck. I'm sure that it was pretty well serviced as it has 300K miles on it and it's still running pretty decent.
I picked up the truck and I have to get the smog done soon. It idles with what I can only describe as a slight miss and it runs and drives great. seems to have plenty of power for the miles that's on it.
There is no active CEL on but I scanned the OBDII system and found a P0171 Lean bank 1 code in the pending codes list of the scanner. I guess this year engine doesn't have an EGR Valve or DPFE sensor because I've looked high and low for it and there non existent on this engine.
I've checked for vacuum leaks by spraying brake cleaner or carb cleaner all over the place and it makes no difference and all the vacuum lines and connections look okay.
When it's running It does sound like a vacuum leak right behind the top of the plastic throttle body but I can't find it, I don't know if this big *** engine just sucks that much air or what.
Like I said I need to smog this thing soon and I don't want it to fail if it's missing or has another issue. The fuel injectors look new and one coil pack looks like it's a replacement...
View 14 Replies
On a 2000 F-350 with 5.4 engine, where does the vacuum line enter the cab? I got a truck in with no vacuum signal to the heat controls, and it has a slight miss at idle. Both of these are signs of a vacuum leak, but i can not find the line going into the cab.
View 5 Replies
Alright, I have a 2002 f350 7.3 4x4 ext cab xlt with 300k miles. Bought in may 2016 with 260k miles and towards November started running rough and felt like a loss of power. Had a no start but a new gray cps fixed that issue. Running fine. About a week later started it up and it had a rough idle, felt like not all cylinders/injectors were working. Was "knocking" and a loss of power. I was in the army at the time and stationed in Georgia, took it to a local diesel shop in Georgia and they confirmed my icp sensor was bad and injector #1 , #5 #7 were bad. Work was busy and money was scarce so I left it as it is and was saving up to buy the new parts. Then one day approx a week after the visit to the shop, I started the truck up and it ran fine. No misfire no knock no rough idle, drove fine for about a month.
In December, I was on vacation in florida to see my parents, drove the truck down, ran fine. While on vacation one day in a Walmart parking lot the truck didn't start up. Couldn't fix any issues then so towed the truck to my parents house. Did more troubleshoot, replaced fuel filter, cps, ipr valve, icp sensor, glow plugs, glow plug relay, ebpv pedestal was replaced with a ebpv delete pedestal. All parts bought oem and/or from riffraff diesel. Still would not start up. So then I bought a refurbished IDM from eBay, oem and then the truck finally started up one day but running rough again like it used to, then it wouldn't start again. So then, I replaced the PCM with a reflashed/refurbished one off eBay and boom truck started up, still running rough but now it starts up every time.
Now, took all eight injectors out and replaced all the o rings. Cleaned them up and put them back in, truck still running rough. Injectors didn't appear damaged nor the wiring harness so now I bought three reman injectors from riffraff. And replaced those three bad injectors. One of them is not spitting oil out the oil spout on the injector.
My dad has worked on freightliner semi trucks for years and is fairly knowledgeable when it comes to diesels. However he did something very amateurish the other day. So two injectors were installed while we were still waiting on the third in the mail. He wanted to see how the engine reacts when that one bad injector was not in play, but instead of unplugging the injector under the valve cover, he cut the wire outside the valve cover to the injector. He stated it's not a big deal and he can solder the wires back together. But once he cut the wire, the truck sounded a lot stronger, still rough idle but definitely stronger. Before, you would be pedal to the floor and the truck barely moves forward but now the truck will lunge forward. A big difference in power.
Now today, third injector came, swapped them out and fired up truck. We didn't solder the wire yet just quick connect, same you would use to connect wires for a car stereo. The new injector was not spitting oil out the oil spout. Even at high rev and truck warmed up. Truck still runs better with that one injector unplugged.
Tomorrow we will troubleshoot if somehow there's wires that grounding out or burnt out somewhere but as of right now everything seems to be in order, the uvch are tight, and no signs of anything burnt.
Triple checked everything, still getting fuel pressure, still getting oil pressure what gives? I also replaced the MAP sensor. Fuel pump is fine, fuel gets to fuel bowl. The next thing I'm thinking is maybe the hpop but we have oil pressure so idk..
View 5 Replies
My issue is not with the truck starting its with it staying running. I had plugged in all the night prior and all day while at work. When my shift was over went out started fine let it run for about 20 minutes and left to make my way home. During the trip it ran fine for about 1/2 a mile and then it started idling really rough at a stop light went to go threw the light and it as though I had left it out all night with plugging it in. I went to turn on a side street because this situation was not going to end well and it died trying to turn. It would not start back up I was able to get a jump and made another 1/4 of a mile and it died right in front of my house. I replaced both the batteries this morning and it fired right up lasted about a minute and then died again. All the gauge read fine, oil level is good, and the injectors were replaced 2 years ago.
View 14 Replies
I have a E350 5.4 with 200,000 miles and it ran great before winter, this spring I fire it up and it got a miss I drive it anyway it starts to clear up and now the 1289 code. Everything looks fine coolant engine temp. I wonder if you can bypass the Cylinder Head Temp sensor. I am thinking the engine management is causing the miss to cool the engine.
View 3 Replies
Got a 99 F450 7.3 with 190k miles, started acting sluggish. When cold, it wouldn't stay running, almost as if out of fuel. Would stall out when you pressed and released the accelerator but would idle fine. Now, it won't even stay running. Still acts like it's out of fuel. Changed the air filter, fuel filter, and added injector cleaner and conditioner. What else could it be? after warming up when shifting gears and letting off throttle it stalls and when restarted lets off blueish white smoke.
View 2 Replies
i have a 2002 f250 i drove it lat night parked it came home from work at about 3 and noticed my head lights were on and just headlights. I open the door and see that the switch is in the off position too. WEIRD HUH ? they wont go off. I tried to unplug the switch and nothing.
View 6 Replies
My 99 f250 ran hot while towing my travel trailer when the fan clutch gave up. ever since iv been noticing coolant loss and pressure in the day tank.ive changed the water pump,radiator. day tank and cap plus the thermostat.
View 9 Replies
I have a 2002 f250 SD v10 4x4. I had a ground wire break fixed that know noon of my instruments work. Dash lights up but nothing moves. Pulse my parking lights stay on when the truck is shut off or when I turn lights on then off. I have to disconnect the battery to get hem to shut off.
View 3 Replies
I have a 2004 Ford F250 with 174,000 miles the truck has a slight miss a rough idle one hot or pulling I have 2 codes nut no light when I go into the ford oem feature in my scanner a PO 272 and a PO404 .. Where to start?
View 4 Replies
2002 Ford F250 4x4 Superduty Lariat (4 door). Just changed the locking hubs to a new set of Warn manuals. I began to periodically hear what sounds like a rumbling/bearingish/howling kinda sound. Happens when you hit a bump at any speed...then howls till you hit another bump..goes away..then process repeats. Come to a complete stop, and the sound usually goes away till you hit another bump. The hubs are "free" at this time.
Heres the weird thing...when the noise starts...I switch it into 4 wheel drive on the dash...the sound instantly goes away. Click it back outta 4 wheel drive (hubs are still unlocked this whole time) and the sound is gone. drive some more down the road, maybe hit a slight bump, and the sound returns. Switch it back into 4x4...sound instantly goes away. Its not really in 4 wheel drive, cause the hubs aren't locked in...but that cures it till I take it back out. What could be causing this howling ? Its getting worse, and you can feel a slight vibration in the floor now when its doing it.
View 8 Replies
Had this truck a few years now, and it has always had a slight miss/hesitation and maybe a few codes. The timing chain skipped a tooth and the truck was down for about a year. I have 4 other trucks, so it wasn't a big deal. I finally had time to put a new oil pump, chains, guides, tensioners, phasers etc. The truck actually runs very well and quiet. But, now misses far more than I remember it doing.
When driving in town constant at 25-30 mph occasionally it will loose power for a brief moment(<1 second) and then be fine, the security light on the dash turns on for a few seconds. It drives at 55-65 just fine, unless I am going up a hill or something else increasing the load.
2004 5.4 3v 2wd
CEL-
P0453 (fuel tank pressure issue)
P0351 (ignition coil a primary/secondary circuit malfunction)
P0356 (ignition coil f primary/secondary circuit malfunction)
The coil packs are new, and I have injectors on order. Also found this thing on the back of the motor, it connects to the fuel rail on the drivers side. Where it should go. I looked on my other trucks. But my other 04-4wd has a box by the battery it connects to, but mine doesn't have any of that stuff. And my 08 doesn't have anything like this at all.
And a pix of the truck in question.
View 2 Replies
2002 Ford F350 7.3...
After replacing the Glow Plug Module and the cam sensor. I have no codes on the scanner. However, after driving the truck for one hour or two it stalled and after cool down about a while t started and stalled after hot. Now I been reading lots of info and this is what I got so far.
Flow Sensor
Fuel injector control
Fuel pump
And one person said that he change the wire harnesses for glow plug on top of the head covers?
View 3 Replies
2002 7.3 running rough.
This is my symptoms : On cold start ups engine runs rough. Idling it knocks worse than normal on the road she runs really rough. If I get on here she smooths out ( but still runs rough a bit) but normal driving at between 1200 -2000 rpm she runs so rough it shakes the whole truck. It will do this until she gets up to operating temp & then it goes away. The more she warms up the better she runs.
Once up to temp she will run perfectly. The colder it is outside the worse it is & the longer it takes for it to go away. I have replaced the valve cover gaskers and new harnesses, new glow plugs. Still same problems. I have AE and one time it gave me a #2 cylinder code. have not been able to repete this code. What to check next.
View 5 Replies
One of my work trucks is a 99 F-250 5.4L. Up until recently it's been running strong. Then one day it's like someone flipped a switch, and now it runs like it's losing power.
Symptoms: a quick short stumble when you first hit the accelerator. While driving, it takes the entire pedal to accelerate. Even with the pedal to the floor, it won't keep up with traffic. Driving uphill, it will barely maintain 40 mph.
I've checked everything I can think of. Fluids and filters are all good. Battery and alternator are good. There are no trouble codes. I have Autoenginuity with the Ford Bundle, and the truck passes every diagnostic test I throw at it.
There's no smoke. It still idles pretty smooth, although there is a slight and very quick random shudder in the idle that has started at the same time it started losing power.
Transmission is good. The last thing I tried was to change the fuel filter, but that made zero difference. Quick question, does the tank on the 5.4L trucks have a pickup screen like the diesels? If so, I might try blowing some compressed air through the fuel line and see if it dislodges anything.
So that's where I'm at. It has no power, yet I can't find a single thing wrong with it.
View 14 Replies
I have a 99 F-250SD with 5.4 automatic that just all of a sudden started running unevenly at random times, but frequently. There is a pending code P0300 Random/multiple cylinder misfire. I have had the truck for 12 years and it has run perfectly for the last 10+ years and just started this problem, it did not come on slowly but all of a sudden. I have seen on here that some people say that 90% of the time a PO300 is a bad cop. I replaced the plugs 60k miles ago when I had a bad coil on plug 10 years ago that did not set any codes, but this seems very different that more than one cylinder seems affected, like maybe 2 or more cylinders are not firing momentarily.
There is a big power loss momentarily while it happens, but doesn't happen for long. The fuel pressure stays pretty constant (30 psi at rail) even while it happens, and it can affect the idle as well as while accelerating or cruising at speed. I cant imagine more than one coil on plug would be skipping at the same times or fail at the exact same time, but maybe having only one bad cop could cause this much hesitation? Does the code that indicates random/multiple cylinder misfire rule out only one bad cop? It just seems like running on 7 cylinders wouldn't be so noticeable. Could a sticking egr valve cause unevenness at idle and higher rpms and set a P0300 code? Would checking manifold vacuum be they way to see if egr valve is not working correctly.
View 11 Replies
So I'm not sure if I bought a lemon, but i picked up a F-350 6.4 Turbo Diesel two days ago and the check engine light came on yesterday. It's giving me a P0088 Code as well as the P0088pd. It's got 131,000 miles on it so no warranty will cover me.
I'm tracking the TSB put out telling the techs to replace the HPFP, but they mention a loss of power. I've only had the truck for two days, but I've driven them for work before and I can't detect any loss of power. Besides the code, everything seems to be running fine.
What can I can try out before running out and changing the HPFP? I'd rather not cut so deep into my savings if I don't have to.
View 6 Replies
Last night, I left it running while unloading a trailer and come back to notice it was idling abnormal. I jumped in it and tried to move it and there was a noticeable loss of power. I unhooked the trailer and tried to get it home. I only made it 1/2 mile down the road when it started spitting and sputtering (surging ever now and then) to a level that it died completely. I was able to start it back and get it out of the road but had to be pulled into a drive. It got to a point it wouldn't start back at all.
Today it started up however still had a rough idle and really has no power to speak of. The more I messed with it the less power it seem to have.
I have searched the forums and tried these things:
1) Checked the oil and noticed it was on the low end of the operating range. I put some in it to put it back to normal.
2) Disconnected the ICP
3) Changed the crankshaft position sensor
4) I dumped the fuel bowl after it completely died (in case it had any water in the fuel bowl).
The fuel filter was just changed 2 weeks ago. The fuel pump seems to be operating correctly (or it at least refilled the bowl) and started again with a very rough idle.
It doesn't have a engine light on nor do I have anything to read any codes it may be showing.
View 14 Replies
I have a 2004 f250 superduty. I lost all electric to truck. No lights, radio, etc. Turn key and no click or dash lights. I put a charger directly to battery and nothing. Is there a main fuse in power line prior to the fuse box under the dash??
Also, right before this happened, I went to start my truck and my batteries were low, the truck turned over a few times, started dying, so I turned the key off, and the truck kept turning over on its own, as if the circuit remained closed for ignition due to low battery, and it turned over by itself until the battery was completely dead. But putting my battery charger on it now gives me no electric at all.
View 5 Replies
