My 02 ford V10 is hard starting. If I start it every day, it will start and run well. If I let it sit longer than one day I need to spray some starting fluid to get it to run. I turn the key on and let it pump up before I try to start it. After it starts with starting fluid, and runs for a minute or so it will start up with no problem.
View 14 RepliesBeen driving my 2001 f250 7.3 4x4 with no problems then started noticing it lacking power so I changed fuel filter and air filter. After a week goes by I was at work and I was leaving to come home so I started truck to let warm up and it cranked longer than normal but started. Let run about 10 minutes idle nicely when I punched it it bogged down and had no power never died. I idled over into parking lot and power came so I took off again loss all power again, still never died. Got it right back to my work sat there a bit and tried again this time I took it easy and was able to get my truck home 30 so miles.
When I got home I ran codes p1211 came up for the icp sensor I changed it did not change anything still had same problem. This was a Saturday afternoon to evening issue. So sunday I played around with it just checking out info online and test driving it seem to run ok but still lacking power. Let it sit till Monday I went out to start it had to cycle key 3 time before it started idle nicely then died would not restart changed ipr valve nothing changed cam sensor nothing changed some how 10 quarts low in oil just changed dec. 30th don't know ? Now will start if I pump throttle and has all its power back?
My 2011 f-350 6.2l cold starts hard, it cranks through 2 cycles sometimes before it fires, then it might stall. Sometimes it stalls if I put it into drive or reverse before its warmed up. It has also misfired on one or several cylinders during startup. It has also misfired while driving. It has never stalled when driving. I have replaced the canister purge valve, I have done a full tune up with all factory plugs. All with no change to how it starts. My next step is a Pcv valve, I have one coming from ford today.
View 5 Replies02 CCSB, and I have a vibration in my driveline that's starting to drive me nuts on my commute every day. I can feel it faintly starting at about 45 mph, whether the torque converter is locked or unlocked. The vibration peaks at about 60 mph and goes away at about 65+. My u-joints are all moog and grease them every oil change (about 120k on them now). At this point I suspect the carrier bearing, yokes, or even u joints but there's not much play. However the rubber around the carrier bearing is in rough shape and dry rotting. I'm curious if there's a test I can do to find the culprit.
View 1 RepliesNeed to diagnose my truck issues. On my 2002 F250 V10, when I try to start it, the engine just cranks and cranks and cranks with no fire or even hint if starting. I am not sure if it has no spark or isn't getting any fuel. I just replaced all ten spark plugs and coils less than 500 miles ago. I want to perform the fix myself, but I need to get the problem diagnose the issue first.
View 8 Replies2002 F350 5.4 . I did some plowing today, truck ran Great, but noticed the Auto Shifter starting to get some play in it, 185 k on it. I recall reading about how to tighten it back up.
View 3 RepliesI have a 2002 ford f250 with the 7.3l diesel. I recently installed a ts performance chip. On my pcm. And after i first tried all the different stages I didn't like how my transmission was shifting hard. So I contacted the manufacturer and he told me they could reprogram the chip for smoother shifting. So I removed the pcm and removed the chip. But when I went to reinstall the pcm I bent one of the pins on the pcm some how.
So I took it back out and straightened the pin with pliers . i reinstalled it back in the truck. Only to find when I reattached the battery cable I have no power to anything ignition ,horn, lights,Cigarette lighter etc. So my question is if the pcm is bad, or not contacting properly due to the pin being messed up. would that have anything to do with the lights and horn and all that? I suspect its the gem bsm or Vsm. Whichever one my truck has. But really not sure because everything worked fine just 20 min b4.
I have been having hard shifting from 1st-2nd when cold. Rpms up to 2000 and let off then goes into 2nd. After that, she shifts fine and shifts well until next morning when she sits overnight. Build tag is August 09, 2001, so no old mechanical diode? Took a sample of fluid and it is dark red (pic attached) and smells like hydraulic fluid...I don't think it smells burned. Does it sound like the calve body 1-2 shift or solenoid pack or needing rebuild?
View 3 RepliesDealing with a 02 f350 7.3 powerstroke . The engine cranks fine . It fires but won't start smoke coming from exhaust while cranking and firing so seems to have good fuel . When it does start it misses for a few minutes and blue/white smoke . When the miss ends so does the smoke and starts fine after that and runs great until it sits for 12 or more hrs . Then back to same start issues . Fresh oil ,new glow plugs, new cover gaskets , glow plugs test at 1.3 ohm across all 8 of them , no voltage drop through glow plug relay , good voltage to each glow plug when tested right at glow plug terminal on each feed right at glow plug , fuel filter housing stays full doesn't seem to bleed back , high pressure oil pump pressure test was high enough to trash a 1000 lbs gauge in 2 to 3 revalutions of engine when cranking . Tested at presure sensor port .
View 2 RepliesWorked with the 6.0s on my ambulances at my station but this is my first personal diesel. Starting about a week ago my 2006 F350 with 88k started having longer cold cranks, around 10 seconds with some hiccups on the way. I checked the FICM Voltage with a multimeter and on my scan gauge II, it has not gone below 47 volts. I am above the 500psi on the ICP, and around 35% on the IPR Duty cycle. The FICM is also synced. I know this is a big topic with these 6.0s but normally one of these things are an issue, where as mine are in normal range.
View 6 RepliesI'm having a problem with my 04 f250 6.0. I replaced my brakes rotors and calipers yesterday along with my fuel filters and after I took out my air filter to check it and put it back in my truck will no longer crank. When I put my key in the on position all of my lights and dings happen but I don't hear my fuel pump and when I go to turn it over I get nothing at all.
View 8 RepliesI screwed up installing LED taillight assemblies in my 2011 SuperDuty and pinched a couple of wires against the body. The result of this (at least I think that this cause) is that my backup lights no longer work - neither the backup lights in the tail light assembly nor the reverse light power on the trailer plug. I have checked the fuses, etc. and nothing. I brought it to a local shop and they could not figure out the problem, either, but said that it was probably the "control module" that got fried when the wires got pinched. They said to take it to the dealer. The questions are, what "control module" might they be referring to, or what to check?
View 1 RepliesRecently removed a plow and wiring harness from my 00 F550 and now my headlights no longer work. The headlight plugs have an adapter that the plow harness plugged in to and it now appears I need some type of end plug on each one to complete the circuit. The problem is the dealer doesn't understand what I need and doesn't think there is such a part out there. Perhaps my thinking is all wrong.
View 3 RepliesI just got an 03 6.0 and a few days ago it developed a rough idle, it takes a little longer to crank and idles fine for 30 seconds to a minute then the rough idle kicks in also I noticed when I drive it the low rpm range is a little choppy and when I come to a stop it goes a little below idle then resumes the rough idle issue. I had it die on the road a day prior to this after it lost complete power at a red light, it started to idle low so I tried to counteract with a little throttle and with the throttle all the way it did nothing, a few minutes it died on the road and took a few minutes to start back up I did a set of filters and it hasn't done it again but I still have the rough idle, I checked the icp sensor and wiring no oil so I cleaned it up a bit and it runs a little smoother.
View 2 RepliesI have a 2013 F250 with a 6.2L gas motor, 50k miles.
Recently, I've noticed it takes longer to start. The motor will crank at regular speed but will take longer to start. It's always taken longer than a single rotation from day one but lately it's gotten really bad.
Even more recently, I hear a ticking noise under load, or even sometimes at idle. It sounds like an exhaust leak or worn lifter noise. Could these somehow be connected? What this could be?
It used to be, if I remember correctly, that while turning the key on a cold start the oil pressure gauge needle would show pressure prior to the engine starting, now it takes longer to start and the needle doesn't move until after the motor has started. I had the O-ring kit replaced due to oil leakage, and I wonder if there is an issue with the system. N to watch as they deedo their cold start today...
View 4 RepliesI just installed a set of power folding mirrors on my 2008 F350. I noticed that the driver side mirror has a longer travel time than the passenger side. How to fix, or why this is like that? Is it normal? watch the video to see what I mean.
[URL] ....
I work for the transportation department at a school and we have a bunch of 6.0 f350/450 busses and this bus I am working on has a no crank condition. Bus in question is a 2006 F450 6.0.
Currently if you turn the key to start the engine the solenoid just clicks but the engine wont crank. The person working on it before me assumed that the batteries and or starter were bad so they were replaced(0 miles on them right now) but the problem still persists.
First thing I did when I started working on this bus was jumping the starter relay and the starter engages and starts the engine perfectly. That being said I know the starter wiring is fine.
Secondly I looked through the wiring diagrams and saw that the PCM grounds the 85 terminal on the starter relay so I tried grounding the 85 and I was able to crank the engine with the key so that was telling me that the actual starter relay is fine. Next I went and swapped the PCM with another 2006 f450 thinking maybe the grounding switch in the PCM was bad and I have the same no crank condition. The PCM from the bus in question was swapped to the doner bus and it cranked perfectly(PCM in question is fine).
Next thing I did was look up all of the ground locations for the PCM or anything to do with the starter and they were all cleaned and still have the same no crank.
Looking around on the internet I see that the viscous fan can cause a problem if it shorts out so I unplugged that and no change in the no crank. I also saw that the trans range sensor could cause a no crank condition but I am getting back up lights/beeper and the bus "wants" to crank so I am thinking that the TRS is not the problem.
Lastly I tried hooking my Modis scanner up to this bus and was NOT able to communicate with either of the PCM's I tried. Not sure if this is related to my no crank condition. I checked all of the wiring that I could but could not find any chafing or breaks in any of the OBDII wiring. My planned next step is to replace the TRS...
I was wondering if there is a aftermarket product to give my truck a more Rumble when starting and idling.
View 8 RepliesI am looking at purchasing a 1999 f250 Crew Cab Long bed with the V10. It has 120,000 miles on it and has been very well taken care of and maintained. The current owner says that over the last couple of weeks it has started to start sporadically. The first time it did it was after a 30 minute drive. Parked the truck outside his garage and a hour later when he went to pull it in the garage, it wouldn't start. He called a mechanic friend that told him to trip the inertia switch.
Pressed the switch, it clicked, and then the truck fired right up. Since then it has done it twice more but now instead of tripping the inertia switch he turns the key on and off 10 times and then it starts right up. What this would be? I would normally think fuel pump since cycling the key on and off would be building pressure in the system if the pump was just starting to die but the inertia switch being tripped has me confused.
The owner thinks or was told that quickly turning the key off and on is resetting the computer and after turning the key 8 times the locks lock and unlock and the lights flash once. Is this what it is doing? I thought turning the key on and off in multiple succession let you manually read the codes...
My 1999 superduty seems to be hard to get the 4x4 lever out of 4 low, truck has a 5.4,auto transmission and manual hubs and manual shift lever...
View 6 Replies