Ford Super Duty (1999-2016) :: 2002 - Stripped Coil Retainer Bolt
Jun 9, 2010
I've a 2002 Ford F250 SD with the 5.4 v8. I noticed my truck is missing at aprox 50mph when the truck goes into OD and revving at aprox 1500 rpms. I Changed my spark plugs and cylinder no 6 was fouled. The coil was cracked where the sensor connects to the coil. I used some JB weld to try and repair the crack. My truck is still missing and vibrating at 1500rpms at 50mph. I wonder if I need to replace the cracked coil? my check engine light is not on, but that means nothing.
Also, cylinder no2, I was not able to remove the coil. The bolt is stripped. I just got this truck a few months ago and the previous owner or last person who worked on this truck left me with a stripped coil bolt. Anyway, how do I get this bolt out? I'm afraid to crack the plastic area the retainer bolt threads in to...which is also plastic. I"m not too fond of my ford, at least working on it.
View 14 Replies
Advertisement
I have a 2000 F450, 7.3, 4x4, dually, VIN 1FDXF47F0YEA44380, with 30k miles, That needs a new rear axle - hub retainer threads on axle housing are stripped (nut welded on by previous owner). This axle is a case ID F81A-4001-BK, 4.88 ratio, 11.25 ring gear, with a 41.5" spring center. I have heard that the '99-'02 axles had issues until Ford switched over to the later square housed axles in 2002 or 2003 (Dana 110, I think). Is it possible to adapt these later (2002- 2004) axles onto a 2000 F450? And if so, what would be involved?
View 3 Replies
2016 F250, took out the seats to remove the console and install the jump seat and upon installation I stripped the bold housing for the front left corner of the drivers seat. Now it won't tighten up. Am i going to have to tap the hole and get a bigger bolt now?
View 12 Replies
So I went to install a front end leveling kit in my 2003 2WD F250, looked like a simple task, except the bolt that holds the lower coil spring mount won't budge! I tried heating the nut, I soaked it with WD-40, tried a 200lb impact and a 30" breaker bar with all my weight. Is there something I am missing?
View 5 Replies
One of the super coils busted while driving my 2002 F250 Super Duty. I drove it for less than 100 ft. before parking it. It made a rapid "check,check,check,check" sound, which I'm assuming was mainly the coil smacking against other parts while loose. It busted near the point where it screws into the motor. I felt like I lost some compression as it drove sluggishly once broken, although I only drove for a very short time. I also thought I may have smelt a slight burning scent, or maybe oil, but didn't smell anything once I got out of my truck. Any problems I should look forward to other than simply replacing this coil?
View 14 Replies
Went to change the plugs on an 02 f350, the bolt holding the plug wire boot on doesn't seem to fit any standard size socket. 7 is too big, 6 is too small. 1/4 is too small, 9/32 is too big.
View 14 Replies
My 2002 F250 Crew/Diesel/4X4/lariat has ever since I bought it, had an electronic problem.. sometimes I start it, the heat coil light stays on, sometimes the radio won't work, the windows won't work.. then about 2 minutes later, they work, my back up alarm always comes on turned off... sometimes my fuel gauge registers weird, ....
View 1 Replies
I have stripped my HPOP fill plug. Any experience on getting one out? And a part # for a new one?
View 10 Replies
I noticed a thumping sound in the truck bed when I'm driving and took a look underneath. The rubber gaskets for the truck bolt are all rotted and falling apart. Does it have to be replaced?
View 5 Replies
Need to know if the 5.4 and 6.8 use the same bell housing pattern?
View 5 Replies
My 6.0 lost a bolt that holds the AC clutch and the clutch fell off. It's probably on some highway making people have flats. Is it possible to buy a replacement clutch and NOT remove the OEM pulley, just take the parts off the replacement clutch and put them on the old AC and existing pulley?
View 9 Replies
What is the thread size/length of the 20 transmission pan bolts on the 4R100? I am replacing the pan since the rust has finally started weeping ATF, and the bolts need to be replaced as well, they have turned into little rusty nubs. So i want to use stainless ones. I could pull one and go to the hardware store, but what is the size i can stop on the way home.
View 14 Replies
What is the size of the bolts on the rear axle that hold the shock absorber? I believe its an M12 x70 mm long??
View 7 Replies
My steering wheel is loose as in moves back and forth if pushed or pulled right at the wheel.. everything else seems tight and still turns and drives fine.. took off the airbag and the center nut is tight.. it's been getting progressively worse since I bought it.. What it could be??? Loose bolt or nut or the steering column?
View 2 Replies
As part of my ongoing P1393 troubleshooting, I’ve found that I can’t get the main engine wire harness separated. The big connector by the driver’s side valve cover.
I’ve cranked and cranked in the correct direction, but the plug never separates. I tried a cordless impact wrench and it still doesn’t move. (Edit -- the bolt moves very freely, but it doesn't push out one side (e.g. like removing the PCM) I can't figure out how to separate the two sides.)
Any tips on how to get it separated? Can I cut off the bolt head to get it separated?
View 14 Replies
I have a 99 F250 Super Duty 4x4. The u-bolt bracket on the front passenger side has rusted through and broken in two places. It has broken right at the hole for one of the u-bolts, which then broke the sway bar bracket off (so the sway bar is no longer attached on the passenger side). Also, the track bar bracket has broken off.
Is there a replacement bracket that can be purchased? Or does it need to be fabricated from scrap? The u-bolt bracket, sway bar bracket, and track bar bracket are all one whole piece. It is welded to the axle, so it would need to be cut off. Then the new bracket would need to be welded back on.
View 14 Replies
I have a 2009 f 250 5.4 v8 trition motor my coil packs are slowly failing. I want to replace all 8 of them. Which coils and plugs I am going to need. I guess I'll replace the plugs also, how are the accel coil packs and ngk plugs....
View 1 Replies
I am getting ready to make a set of front shackles for my truck for a temporary lift solution to fit my 35s until i can afford a complete suspension lift kit. I cannot for the life of me find the size of the hole for the bolts. I don't wanna drill it too big then have play in the shackle. My stockers are still installed so I don't have those to measure just yet. Need to verify the diameter hole i need to drill? and stock shackles look to be about 5.25" center to center, from what i can measure with them installed on the truck? so 2" lift, the new shackles will need to be about 9.25" center to center, right? (add 4", nets a 2" lift?)
View 7 Replies
My 2000 f350 is leaking oil from a bolt on the passengers side valve cover. it is one of the bolts on top of the valve cover. Can I just remove the bolt and put a rubber washer under it or do I need a new valve cover?
View 2 Replies
so while replacing the rear brake lines in my 2001 F-250. / 5.4, the flex line that drops from the frame bolts to the axle through the axle breather threaded vent line. The friggin thing crumbled on me and now I can't find a replacement for it. Where I can get it or what it's actual name / part number is so I can call the Ford dealer and hope it's not obsoleted?
View 3 Replies
I have a 03 250 5.4 with 160k. I just recently replaced #4&3 coil packs. Truck was running great again. Then a few days later the truck was running extremely rough and white smoke from the exhaust. I noticed the pcv valve was not all the way in(pretty much out) put it back in and ran fine for two days now running rough every now and then and the pcv valve is making a vibrating noise but stops if I pinch it slightly. I did replace the plugs a year ago.
View 14 Replies
