I have a 2002 f350 7.3 PS that every time I touch the brake pedal it blows the #6 fuse(trailer tow brake/turn signal). I need to use my trailer.
View 14 RepliesWindshield wipers, and washer were suddenly not working the other day, so I discovered a blown fuse. Put a new one in, and it immediately blew again. So there is definitely something grounding out, and I am suspecting the wiper motor itself because so far I have not been able to find any wires shorting out, but before I go to the trouble of pulling the motor out and testing it, or replacing it.
Truck is a 2002 F350CC 7.3 TD. Wipers were working fine the other day before I pressure washed it, which is why I really suspect the wiper motor itself.
So, before I noticed a problem, all I had to do was a slight touch to the brake pedal, and the brake lights would come on. Now, they MAY just quickly flash and won't come on unless I really push hard on the pedal, such as at a complete stop.
I've noticed some issues with trying to lock-in 4W-LOW now too, and I know the brake pedal has to be pushed to engage 4W-LOW. Never had problems before now. 1999 F250 Superduty ...
2008 F350 6.4 diesel. I have the listed truck in the heading, my #9 fuse which is for the interior lighting, lighted running boards and it is a 15a fuse, keeps blowing as soon as I touch the fuse to the fuse box to replace it. I have look at all the map lights and interior lights and can not find any thing out of the ordinary, all of these light were working fine, also my cruise control and the back up sensors stopped working and they are not on the same fuse and the other components that are on the circuit with the crule and back sensors still work, I know that this is a lot of different things but hate chasing electrical ghosts...
View 3 RepliesMy 2005 f350 reverse lights just started to not work . So I checked the fuse and it was blown and every time I put new fuse in it blows, where to check. Sounds like a ground issue am I correct .
View 4 RepliesI have 1999 ford f250 superduty 5.4 v8 I noticed that my tail lights were not working I replaced the fuse as it was blown break lights worked until i cranked up and applied brakes. I replaced fuse again an checked brake lights they worked fine until i cranked truck and applied the brakes i did notice the wires were hot at brake pedal switch when they worked while not cranked. I replaced the cruise control release switch I was told that may be the problem since cruise didn't work. it fixed the cruise control but as soon as i pressed the brakes fuse blew again.I replaced brake pedal switch didnt fix it.
I then noticed a little smoke under tailgate i looked and the wire coming out of connector was hot while brakes applied and not cranked. i disconnected that wire put a new fuse in and brake lights worked in center light and passenger side without blowing fuse driver side however does not work. Because I disconnected the brake light wire to driver side green wire. When I reconnected the driver side brake light wire fuse blew.
So I have it narrowed down to driver side brake light. here is my problem. I have checked all the wires that i can see for bad or frayed /worn naked places i have found none I can get to the wires beside gas tank running the rail to check but it is doubtful that it is spot as nothing is rubbing along there. Could it be a relay somewhere? can i just run a new wire from brake light? if so where to i connect to? Is there a wiring harness i can just buy and replace the brake light wires from brake light to power source I have ran out of things to check on my own...
Every time I step on the brakes, there is a bright spark in fuse #13. My brake lights, turn signals and hazards don't work. At this point my truck isn't drivable.
According to the owner's manual in my truck, says circuit #13 is for "stop lamps, CHMSL/hazard, trailer tow stop lamp, and speed control."
I'm assuming that the hazard part covers the turn signals as well, but I know the cruise control works even when the fuse is blown. I used it last night on the way home (this was before I realized I didn't have brake lights).
So I know I have a short somewhere. The only mods I've done to the lights are aftermarket headlights, but if the fuse only gets blown when I step on the brakes, I don't see what that would have to do with it. Also, the lights have been installed and working for about a month before this started. The only thing that I did around the same time was install the gauges. I ran the power to them from #5, the customer access circuit.
Are there any other "common" areas for this to happen? I already removed the rear brake lights and it didn't work. I am quickly running out of 20A mini fuses.
2002 F450 7.3 Turbo
Ok first problem : Starter Motor fuse kept blowing and I spent weeks trying to figure it out. No luck. so wired up a push button just to get the truck started, its a work truck so it was needed asap.
2nd problem : he truck stopped starting completely. Wont start in Park or neutral and after a NEW STARTER (because I thought the solenoid on the starter was bad I replaced it) Everything work correctly for one start with the key. After the second time trying to start it blew the starter fuse again. So I tried the straight wiring to starter. still nothing. I was wondering if there are any shims or anything at the transmission housing to correctly position the starter. I am thinking that maybe the gear is stuck or gets stuck sometimes. when I straight wire the starter it does nothing but the wire gets hot so I know its pulling.
my dads front drivers brake caliper was dragging so last Thursday he had the local Ford dealer install a new one WHY i don't know since i always work on everything of ours plus my friends Fords. Today he said he pushed the brake and it went to the floor then he let up and pushed it again and they worked?? I haven't looked into it yet but the dealer cant look until Friday morning so my dad asked me to do it today after work..... what should i check for? leaking brake line, maybe air in the system still?
View 4 RepliesI have a 2006 F350, it keeps blowing fuses for the brake/turn signals. The puzzling​ part is it only does this when the truck is running.
View 2 RepliesI replaced all the brake pads on all 4 wheels. Pretty standard procedure. I now have a very spongy brake pedal. It stops but the pedal will be almost to the floor. I did not break any of the lines open during the procedure just used c-clamp to spread the calipers. No ABS light. Have a Snap-On power bleeder and bled the system several times with no change. Checked the power steering fluid level and inspected entire system for leaks.
2002 F-550 V10
I have a 2001 F-350 Diesel 4x4 crew cab 8ft bed dually 7.3 diesel 6 speed. The issue is that the parking brake pedal is extremely hard to push. One day it pushed down and ratcheted into a locked position as normal and the next day I couldn't push it more than an inch down. I have rear disc brakes with internal drums in the rotors for the parking brake assembly. I replaced the shoes and hardware (which were fine) and I still have the same issue. I removed the front single cable from where it splits into the two rear ones and the foot pedal depresses smoothly and with the touch of a finger with no load on it. What else is it? The only other thing is one of the rear cables unless I am missing something?
View 5 RepliesThe other day I got in my truck and started down the driveway when I realized I had no brakes, I slowly backed up and parked it. I haven't driven the truck for approx. 2 weeks and it seemed fine then. The master cylinder is full, there are no signs of leakage from wheel cylinders or lines. Today I unscrewed the left front zert and no fluid came out. My pedal goes all the way to the floor.... Whats going on, and if its a easy fix?
View 14 RepliesMy 2002 f350 diesel recently started acting up, the first sign was when my park brake light came on and the chime came on. I mucked around with a few things but still wont go away, while I was doing this a buddy noticed i had no brake lights at all and under further inspection no signals either, not even the clicking noise you usually hear also the cruise control has stopped working as well as the little screen mounted to the roof near the rear view mirror. I am fairly clueless with electrics (I don't even own a multi meter) but i do want to figure this out, i have noticed that fuse 20 was burnt and after replacing it it pops pretty much right when i push my foot on the breaks or signal.
View 10 Replies2002 f350 5.4L
No rear running lights or brake lights
No third brake lights
Headlights work
No signals or hazard.
I have power to the multifunction switch when I use a jumper wire to bypass the switch I can make the lights come on depending on which slot I put it in. I replaced the multifunction switch twice just to see if I got a new bad one the first time, but to no avail. I cant run my truck a night without the lights.
My problem had been intermittent for last few days. I have a Ford Crew Cab - 7.3 Powerstroke Diesel. The ford store told me it would cost hundreds of dollars to chase this short- to wait til it finally burns out then - bring truck to them.?
My fuse # 45 a 10 AMP fuse . Keeps blowing out. This fuse controls the gauges on dashboard and fuel peddle. I can start engine and if gauges come up like they should- I can place into driver - and give engine fuel from peddle- gauges down dead and no fuel go to motor. It just idles and still runs and will still move forward or backward. But only at idle speed.
I could replace blown fuse - #45 - 10 amp and it would a the first few times would go and work normally.
Now everytime I replace fuse it blows fuse - sometimes after putting 10 or more fuses in- one might work until I stop or put into park. Then fuse blows again??
Last night and today it took no less than 20 - 10amp fuses to get close to home and end up straight wiring with a small piece of electrical wire - severing as a jumper- it ran great - til I stop at mail box and got mail - saw slight smoke and pulled wire quickly out and idled down driveway to house..
I've noticed when I'm towing, on long down hill grades if I touch the brakes I get what feels like a rotor causing the steering wheel to shake. At first it was only mild, but today on a long 6% grade it got really bad. Never does it on a level road, I've tried to duplicate it, only on a long down hill grade, and I'm not getting a pulse in the brake pedal at all, only the shake in the steering wheel. It's probably time to replace the pads anyhow, and I'll check the rotors. What things to look at?? 2006 F350, 6.0 dually 4x4.....
View 2 RepliesStarted my truck the other day no problems,minute into the start truck shuts right off like someone turned key. Checked fuses , #30 fuse under the column was blown, replaced it and tried to start truck. No luck fuse keeps popping. After changing again i was able to get truck started for a second and POP goes the fuse?
1999 F550 superduty 7.3....
1999 ford superduty keep blowing the 30 amp fuse under the dash, want let it start, why this is happening and the cause of it.
View 1 RepliesWhy I"am blowing #19 fuse it is a 10 amp fuse. It is in the passenger compartment fuse panel. It controls the auxiliary powertrain control module (diesel only),Instrument Cluster, GEM Module, Overdrive Cancel Switch, Idel Validation (Diesel only), Overhead Console and Diesel PCM via Clutch. I would like to know where to start looking to solve this problom.
View 12 RepliesI keep blowing the fuse to the headlights. When low beam is on, the right blinker flashes the low lights. When high beam is on, the blinker works. when I turn on the low lights, my cluster light indicators show the right blinker dim and the high beam indicator light is also dim.
View 1 Replies