Ford Super Duty (1999-2016) :: 2002 F250 V10 - Transmission Grunt When Going Into Third And In And Out Of Overdrive
Mar 20, 2015
I recently purchased an 02 F250 v10 4x4 with 150k from a local auto auction. The transmission, for lack of a better term, will "grunt" when going into third and in and out of overdrive. It doesn't seem to slip at all and the fluid looks slightly discolored, but it does not smell burnt. No Torque Converter whine either. A friend of mine who has owned 10+ SDs for his business said I may need to replace the TCM. Not too sure about that, because other than the strange noise, the truck seems to shift normally.
View 5 Replies
Advertisement
On the surface, the F-250/350 seems to have great brakes: big rotors, vented front and rear, and dual-piston calipers front and rear. But, I have two problems:
One is the annoying 'grunt' the brakes make every time you change from Park to Drive, or Park to Reverse, or Drive to Reverse. Its as if under normal brake pressure, the brakes cannot hold the truck from moving against the torque convertor engaging. It's not just my truck, I've heard older SD's with the 5.4L or diesel do this too. If you push the pedal really hard, it won't grunt.
The second problem I think is the root of the first: mushy brakes. Maybe I'm just used to driving european cars with firm brakes, but every time I apply my truck's brakes, it feels like I need to bleed the system! The truck does slow pretty well, and I realize it's heavy, but how can the pedal feel be improved? Maybe replacing the rubber sections with braided stainless?
Lastly, the truck has a 'hill-hold' feature which is retarded in an automatic transmission. My problem with it, is that sometimes it sticks on...engage drive, the truck won't move...a second later its like something gets unstuck and the truck kind of lurches forward.
View 12 Replies
I have a 2002 ford f250 with the 7.3l diesel. I recently installed a ts performance chip. On my pcm. And after i first tried all the different stages I didn't like how my transmission was shifting hard. So I contacted the manufacturer and he told me they could reprogram the chip for smoother shifting. So I removed the pcm and removed the chip. But when I went to reinstall the pcm I bent one of the pins on the pcm some how.
So I took it back out and straightened the pin with pliers . i reinstalled it back in the truck. Only to find when I reattached the battery cable I have no power to anything ignition ,horn, lights,Cigarette lighter etc. So my question is if the pcm is bad, or not contacting properly due to the pin being messed up. would that have anything to do with the lights and horn and all that? I suspect its the gem bsm or Vsm. Whichever one my truck has. But really not sure because everything worked fine just 20 min b4.
View 1 Replies
Tonight i noticed overdrive flashing. No changes in shifting, truck shifted fine. I shut it off when i got home, started back up, light was not blinking, not sure if its like the check engine light and stays on or not. Where light blinks but shifts fine?
View 10 Replies
I have a 2006 F250 with the 6.0 PowerStroke and automatic transmission. I just purchased this truck at an auction about a month ago.
Today I notice the transmission is not shifting into overdrive. No warning lights. If I press the tow/haul button in no change but the tow/haul light does come on. If I press it again (to turn it off) the tow/haul light goes out but still the transmission will not shift into overdrive.
This leaves me at about 2000 RPM at 68 MPH. I just had a Ford dealer perform Transmission service last week. (20,000 miles after the last recorded service.)
I am already not happy with the service I received at the dealer so I am really hesitant to take it back to them if it is something not related to the transmission service they performed.
View 5 Replies
I have a '99 F250 SuperDuty Diesel with an Automatic Transmission. There is a button on the end of the gear shift which allows you to turn off overdrive -- in other words the transmission won't shift into overdrive once you press the button.
Here's my problem. I start off driving normally. I've not done nothing to the overdrive button and the truck shifts normally into overdrive. 10-15 minutes down the road, the overdrive light (which indicates the state of the overdrive button) is FLASHING. Pressing the button doesn't stop the flashing. Once this flashing starts, the only thing I notice is a much more abrupt shift from 1 -> 2 gear.
View 14 Replies
I have a 2001 F250, 5.4, 4X4. My ignition key stuck in the start position and when I pulled it back to the run position, everything seemed ok. As I started down the road, my speedometer stopped working and my overdrive light was flashing. Also my turn signals had stopped working and my A/C clutch didn't engage. Figured I burnt a fuse. I looked in both the under dash and power distribution box and all seemed well. I checked the fuse for the turn signals/flasher and it was fine. The flashers worked. Thought I might have fried something so I replaced the ignition lock and switch. Also my service engine light came on throwing a code for the vehicle speed sensor.
Looking for solutions on this forum and the internet, I learned that the turn signal switch could have gone bad and the VSS sensor is on the top of the rear dif and an easy fix. Well replaced the sensor but nothing changed. So I went back to the fuse box. Examined every fuse, big and small and I found a 10a with a small space. This was #24 under the dash. From the manual, "#24, 10A, A/C clutch, Blend Door Actuator, Trailer Tow Battery Charge Relay Coil, Four Wheel Anti-Lock Brake System (4WABS), Turn Signal." Replaced it and everything went back to normal. Turn signals work, A/C clutch works, no flashing overdrive light and speedometer works. All from a 10A fuse. If you have any of these symptoms examine all the fuses carefully. There's a 20A fuse for turn/hazard lamps and this other one buried that's only 10A.
View 1 Replies
The problems that I am having at the moment are that the abs light is on from the speedometer, odometer, also the blinking overdrive light that comes on at around 25 mph. After some research I had purchased a ford factory sensor for the rear dif. I then replaced the old sensor with the factory one. Started the truck and not a single thing had changed, both the meters were not working as well as the od light was still flashing.
View 4 Replies
I recentlyHad to replace the right front wheel bearing and after the install the speedometer and turn signals don't work, the ABS light is on and the overdrive light on the shifter is flashing. I've replaced the VSS on the rear diff, pulled and cleaned Speed sensors on front hub?
View 2 Replies
I have a 2002 f250 4.2 diesel with a 5 speed manual box and i want to put a 7.3 in it. Does it fit?and can i make the 5 speed tranny fit?
View 4 Replies
2002 F250 SD 4x4 crew cab, v10. 4x4 not working. Replaced switch on dash, not the problem. Some of told me it was the vacuum control module. Not sure where to start.
View 4 Replies
I been having a issue with my truck lately. It's a 2008 with only 88,000 miles. When doing 55mph it feels like the transmission is slipping. Sometimes it will do it over and over. If I speed up to about 60mph it goes away.its has gotten worse in the last month or so. Hoping it's nothing major.
View 6 Replies
1999 F250 SD... Tranny fluid is low, tranny slipped one time on me. I checked the fluid and it's low. No drips on the garage floor, so I'll have to inspect closer. But my question is can I add new fluid without screwing it up even more? It's got 170,000 miles and I doubt the fluid has ever been changed. I just bought the truck last week, so I can't say for sure, but it hasn't had a regular flush or change. It doesn't smell burnt but it's just a little darker than new fluid. I was told by the guy I bought it from that the torque converter was changed in it not too long ago.
View 11 Replies
I am changing my 99 f250 4x4 from auto to manual tranny. I am just looking for pics of where the hydro line runs. I don't want line rubbing something and ruining line. Like does line run under the cab wiring harness? Like between wiring and firewall? Where on firewall does reservior get mounted usually? Are the holes all ready there for it that I am not seeing?
View 1 Replies
I am again trying to fix my truck. 2005 F-250 6.0 4wd, automatic. Truck now has 89K on it. Truck does not seam to go into lockup mode while driving down the road. it started just after I spun my wheels in a snow storm. No symptom's previous to this. No codes in dash no lights and also no codes when I checked it with an obd code reader.
View 4 Replies
At work weve got an 02 F250 Lariat CC, and the overhead console has gone out. I looked in the owner's manual, and there was no fuse listed for the overhead console. Is there anything that I can do to fix it, or should we just go out and buy a new one?
View 14 Replies
Let me start out by saying that I have exhausted every option that I have read on every thread that I could find on the internet regarding my son's 2002 7.3L not starting. What I have is no 12v power to the starter solenoid at the starter when I crank the key. What we have done so far, had the starter and both batteries tested, all good. Swapped out the starter motor fuse and the starter relay. Tried a new ignition switch and a new trans position sensor. Found major corrosion in the fusible link junction box on the drivers inner fender so we cut out the fusible links and put in a temporary jumper wire, still no crank. I have power to the dash, power on the power cable at the starter. I can jump the terminals on the starter and the starter engages. I found the shifter linkage bolts loose under the dash and tightened them up also. We have been struggling with this for 3 days, out in the lovely Michigan weather, since it couldn't have died in his parking spot in our heated shop, and I am completely frustrated. Are we overlooking something glaringly obvious?
View 11 Replies
I have a 2002 ford f250 superduty and when I have my headlight switch set to auto to come on when it gets dark they will for awhile and then my headlights will turn off for no reason.
View 2 Replies
had a problem with their OD light blinking and shift problems. This past week my od light started blinking and when I shifted into drive, it was stuck in overdrive. When I shift into 1st it would go to 2nd and stay there. So basically I had 2nd and overdrive. I started replacing sensors like the VSS, and checking the wiring warness. Took it to a transmission garage and they told me it was toast. Then I decided to bite the bullet and buy a new tranny. After replacing the tranny it did the same thing with the same codes showing. Then I got smart and checked the fuses. Of course it was as simple as a blown fuse causing all the trouble. In my truck it was fuse 23 under the dash. A 20 amp fuse that was listed as engine control. Im not saying that in every case if the OD light starts blinking it's as simple as a fuse but in my case it was, so lesson learned. Always check the fuses first.
View 13 Replies
I have a 2002 f250 superduty 5.4 4x4 around 317xxx original motor and trans. When it's cold out it won't start at all I have to use starting fluid but once started it will start right back up. Did the plugs fuel filter cleaned the intake and sensors still have a problem plenty of fuel pressure plenty of cranking amps brand new battery and Alternator. It just cranks and cranks when it's warm out fires right up. Runs smooth no lack of power or misfire no codes are being thrown also.
View 14 Replies
I have a 02 F250 V10. When I am pulling a trailer and began to travel over 50 MPH the truck feels like its moving left to right almost like its sliding on ice. Its worse the more weight I am pulling. When I am not pulling anything there is no issues. The trailers I am pulling are gooseneck trailers. What would cause this.
View 11 Replies
