Ford Super Duty (1999-2016) :: 2002 F250 V10 Rough Idle / Misfire Under Load
Aug 22, 2014
I have a 2002 F250 CCSB Lariat 4x4 with the Triton V10, I'm up to 232,000 miles so far and fairly happy with the old girl. Just this weekend, I noticed some hesitation when at idle and even more rough running when under slight load. The misfire/hesitation is worst when going up a slight hill, when the truck is accelerating at low RPMs.
I am getting zero trouble codes or freeze frame conditions on my scanner. What should be my order of diagnosis? Vacuum test at line from PCV to TB, COP test? EGR inspection? Plug inspection? Also, how do you test a coil if resistance is not a reliable method?
View 5 Replies
Advertisement
I have an 02 f250 V10 with a rough idle (90K Miles). It's not horrible but it's obviously not running perfect. Everything seems ok when I am up and driving, especially at freeway speeds. I recently noticed that if the truck is in park and I run the RPM's to 1500 or 2K and quickly let off the gas it will die. It never throws any codes. So far I have replaced the IAC Valve, fuel filter, O2 Sensors, PCV valve, cleaned the MAF sensor and replaced the air filter. Plugs and boots were replaced 5K miles ago. Fuel trim levels on both banks are running around -3.1 to positive 3.5 based on what the computer is telling me. Also according to the computer the vacuum sits steady around 25 at idle (+ or - .2). I don't have a manual vacuum gauge, just relying on the computer. I've also gone around to every plug and disconnected both the injector wire and the COP wire and they all seem to equally affect the idle as well as the fuel trim levels.
View 11 Replies
06 250 5.4 40k on it, usually when cold and accelerating engine will misfire and stutter and then continue accelerating. The wrench light will flash sometimes but it wont store a code. This used to be vague in occurrence but has now started to be more a common occurrence even when up to normal operating temps.It seems only to misfire /stutter on hard acceleration or towing/hauling heavy loads. The only answer I got from a mech would be to do a computer reflash, not sure why /how this would fix whats going on.
View 1 Replies
My F53 motorhome has a rough idle and hard misfire but is not setting any codes. I've put new plugs in it and not change.
View 7 Replies
So basically I thought it would be a great idea to degrease my motor from the top down.... After washing I start it up and drive down the road to head abunch of misfiring under heavy load or high rpm's.
My problem is that the misfiring won't throw a code. I then proceeded to buy a new ignition coil (thinking this was the problem) but with no code to go off which cylinder was bad I just switched the good ignition coil into each cylinder and starting it.
Up each time. None of them seemed to make it better. Also the injectors all seemed to be good. So what to do ?
2002 Ford F-250 5.4l
View 3 Replies
2006 F53 (motorhome) with 6.8L V10. Rcently noticed rough idle and midrange (under load) mis fire. Had codes on 2 coils. Replaced coils and put new spark plugs in. Did not improve and now detecting mild back fire.
Just completed compression test. 1=207psi, 2=200, 3=210, 4=190, 5=197, 6=200, 7=200, 8=170, 9=202, 10=208.
put some oil in #8 and retested at 225!
Other observations on #8. Engine has ticking noise chased with stethoscope to #8. THE new plug with 200miles, insulator going to electrode tip and everything inside combustion chamber is black. All 9 other plugs still look new out of box.
With the ticking noise I was suspecting valve but the compression test with oil jumped way up.
View 14 Replies
2001 f250 v10 6.8l runs a little rough at idle, low rpm is ok between 1700 and 3000 rpm but around 3 it starts to shudder while driving let off gas get back on its fine, new plugs 1,000 miles ago has throttle body spacer and cold air intake, stock everything else..
View 8 Replies
2006 F53 (motorhome) with 6.8L V10. Rcently noticed rough idle and midrange (under load) mis fire. Had codes on 2 coils. Replaced coils and put new spark plugs in. Did not improve and now detecting mild back fire.
Just completed compression test. 1=207psi, 2=200, 3=210, 4=190, 5=197, 6=200, 7=200, 8=170, 9=202, 10=208.
put some oil in #8 and retested at 225!
Other observations on #8. Engine has ticking noise chased with stethoscope to #8. THE new plug with 200miles, insulator going to electrode tip and everything inside combustion chamber is black. All 9 other plugs still look new out of box.
With the ticking noise I was suspecting valve but the compression test with oil jumped way up.
View 8 Replies
OK, not sure where to start so here goes. I have an 02' f-250 with the v-10. I just had some minor front end body work done and when I got it back I noticed that it just didn't feel right while driving. When I start it, I notice a small misfire while I stand next to the exhaust outlet. Nothing too bad, still runs great. Shortly thereafter I started noticing a more habitual missing while driving. Roughly between 30-40 mph and around 12-1500 rpm the truck feel like the driveline is about to pickle fork the truck. If I let off the gas or step on it, the vibration goes away. And very intermittent.
It will only do it when the truck is warmed up. If I only drive about a mile, it won't do it, yet if I turn around and head back, there it is! Now the weird part. I for reasons I won't get into, I left my ignition on and drained the battery. I just replaced it and for the last 2 days nothing. Nt even a misfire. Now today here it is again. I have read all over the forums for this exact problem and cannot find my exact problem. I have replaced the plugs with Autolites and cleaned the coils as well as the boots and applied a small amount of dielectric grease to the top of the plug. The boots are cleaned and not a sign of cracking or wear.
I replaced the PCV valve and nothing. All the plugs looked exactly the same. Light chocolate in color. Not one looked different than the other. I took them out again last week to verify the plugs weren't bad and the new ones all looked the same as well. I cleaned the MAF sensor also. Just cannot figure out what could be doing this all of the sudden. I don't see where anything wasn't plugged back together when it was being worked on and why would a new battery make it go away for a short time? Oh, and lastly, I have a superchips programmer that came with the truck and there are no codes showing and my check engine light has never came on yet.
View 6 Replies
I recently purchased a 1999 6.8L. Runs great when cold but after warming up the idle gets rough. Truck has new plugs and coil packs and fuel filter. Checked the fuel pressure and the idle is right at 30 psi. I read that the good pressure range is 30 to 45 psi. Is 30 psi acceptable or should I replace fuel pump or regulator? Any next step to solving my idle woes.
View 3 Replies
I am new to the v10 I only ever owned 7.3 this is my father truck it's a 99 with 200k on it. The problem is it will idle fine when cold but when it is warned up very ruff idle no codes and when I go back at the end of this week I will check the O2 sensor with AE but I really don't know much about it.
View 2 Replies
I have a 99 f250 5.4l 2v with 165000. just two weeks ago i went to start up the truck on a job site to take lunch and it was running really rough. I talked with a mechanic at my shop and he said that it sounded like the aic or that i needed plugs. I went and bought aic and plugs and installed them all in one day. I unhooked the battery before i did any work and have changed the coil packs about 3-4 months ago when it was jerking at highway speeds. I am at a loss.
Read so much on the site about could be this or that and cant afford to through money at it like the govt does. I replaced the ait(air intake temp sensor) and the ect(engine coolant sensor) after i got a code from oreillys that said p0113 which is high input on it. I have read it can be so many things and it seems to be running rich because i am getting about half of mileage i was getting before problem started. i need a fix soon as i must drive the truck to work everyday which is a 52 mile trip total.
View 14 Replies
The 2003 F250 5.4 Superduty has no power and keeps stalling. If I floor the gas it just stalls. I've replaced the pcv valve and line, the fuel pump relay, the fuel pump, and cleaned the tank, changed out the gas, added Lucas, and it just won't run right. Desperate, and no codes are coming up...
View 5 Replies
I have a 2002 F350 with a V10, this just started happening where at times the truck will turn over but won't run... after a few times of trying to start it I pull the key out let it sit for 5 seconds then put the key back in and runs perfect..... now at the gas station the other day it started but ran like it was on 4 cylinders... I turned it off and restarted it and runs perfect. Heading to Kansas next week to pick up my boat and don't need problems....
View 4 Replies
I have an 02 f250 5.4. I just did the intake manifold. I also changed the spark plugs and the valve cover gasket. Following this I drained the oil and filled it with fresh oil.
It started right up but it felt like the engine was really vibrating and running rough. The check engine light than came on. I don't have one of those tools to diagnose it.
What could be wrong?
View 11 Replies
My truck has been doing this for a while now but it has progressively gotten worse from about three months ago when I went through some deep water. I don't believe it had to much to do with the water, I just think that the water is what didn't deal the situation and lead to the problem becoming more prevalent. But continuing, yesterday it got down into the high 20's and my engine started acting up (rumbling coughing, surging while at/leaving complete stops) and then it finally through a code for once and I head over to the neighborhood AutoZone expecting to get a lean code (because when the engine is acting up really badly I can unplug the fourth cylinder fuel injector without the engine acting any differently) but instead I received the p1152 (bank two lack of switching (rich)) code....
At this point I believe it is a faulty fuel pressure regulator, but without a good diagnostic obd2 reader or a fuel pressure gauge I'm not sure what to do. I'm currently in college, money is low, and I'm trying to take an accurate shot at the part that needs to be replaced so that I don't have to buy more than one part. Of course AutoZone says o2 sensor but I changed both about five months ago.. I've been chasing this diagnosis around for way too long now. (It's on a 2002 ford f250 5.4l super duty)
View 2 Replies
I have a 2007 F250 4X4 6.0 diesel. When first started it idles extremely rough to a point it sounds like a old gas engine missing. But after it warms up for about 15 minutes it runs and idles like a new truck. I'm thinking it's the injectors if so is this something I can change/clean ....
View 2 Replies
I purchased the truck used last summer and this is the second time I've put it in 4wd. The first time was over the summer, and I had a hard time getting it into 4wd, and it made a "clunk" sound initially but drove fine, then went back into 2wd just fine and had driven fine ever since. Today I put it into 4wd, no clunk or any other noises, very smooth, but it drove very rough, almost as if the wheels were out of sync or something. It seemed almost like the wheels were breaking on and off on their own, very weird. When I put it back into 2wd, it did that for a few seconds until it went away. I only drove it in 4wd in my parking garage as I didn't want to risk any more damage to it on the road.
View 14 Replies
Alright, I have a 2002 f350 7.3 4x4 ext cab xlt with 300k miles. Bought in may 2016 with 260k miles and towards November started running rough and felt like a loss of power. Had a no start but a new gray cps fixed that issue. Running fine. About a week later started it up and it had a rough idle, felt like not all cylinders/injectors were working. Was "knocking" and a loss of power. I was in the army at the time and stationed in Georgia, took it to a local diesel shop in Georgia and they confirmed my icp sensor was bad and injector #1 , #5 #7 were bad. Work was busy and money was scarce so I left it as it is and was saving up to buy the new parts. Then one day approx a week after the visit to the shop, I started the truck up and it ran fine. No misfire no knock no rough idle, drove fine for about a month.
In December, I was on vacation in florida to see my parents, drove the truck down, ran fine. While on vacation one day in a Walmart parking lot the truck didn't start up. Couldn't fix any issues then so towed the truck to my parents house. Did more troubleshoot, replaced fuel filter, cps, ipr valve, icp sensor, glow plugs, glow plug relay, ebpv pedestal was replaced with a ebpv delete pedestal. All parts bought oem and/or from riffraff diesel. Still would not start up. So then I bought a refurbished IDM from eBay, oem and then the truck finally started up one day but running rough again like it used to, then it wouldn't start again. So then, I replaced the PCM with a reflashed/refurbished one off eBay and boom truck started up, still running rough but now it starts up every time.
Now, took all eight injectors out and replaced all the o rings. Cleaned them up and put them back in, truck still running rough. Injectors didn't appear damaged nor the wiring harness so now I bought three reman injectors from riffraff. And replaced those three bad injectors. One of them is not spitting oil out the oil spout on the injector.
My dad has worked on freightliner semi trucks for years and is fairly knowledgeable when it comes to diesels. However he did something very amateurish the other day. So two injectors were installed while we were still waiting on the third in the mail. He wanted to see how the engine reacts when that one bad injector was not in play, but instead of unplugging the injector under the valve cover, he cut the wire outside the valve cover to the injector. He stated it's not a big deal and he can solder the wires back together. But once he cut the wire, the truck sounded a lot stronger, still rough idle but definitely stronger. Before, you would be pedal to the floor and the truck barely moves forward but now the truck will lunge forward. A big difference in power.
Now today, third injector came, swapped them out and fired up truck. We didn't solder the wire yet just quick connect, same you would use to connect wires for a car stereo. The new injector was not spitting oil out the oil spout. Even at high rev and truck warmed up. Truck still runs better with that one injector unplugged.
Tomorrow we will troubleshoot if somehow there's wires that grounding out or burnt out somewhere but as of right now everything seems to be in order, the uvch are tight, and no signs of anything burnt.
Triple checked everything, still getting fuel pressure, still getting oil pressure what gives? I also replaced the MAP sensor. Fuel pump is fine, fuel gets to fuel bowl. The next thing I'm thinking is maybe the hpop but we have oil pressure so idk..
View 5 Replies
I have a 1999 F250 Super Duty 5.4L, 118,000miles...engine seems to idle somewhat rough but tach doesn't seem to move off 1000rpm & when giving slight acceleration seems to act like its missing, shaking . But under acceleration moderate or high purrs like a kitten! Always starts good , few cranks. Any hints on the what issue might be?
View 2 Replies
I have a 99 f250 that seems like it has a bad coil, under a load it starts surging or bumping ( like it has in the past and I found a bad coil), I went through and unplugged each coil one by one while idling, couldn't find a bad one, so I bought a new coil and went through and rotated the coils, nothing worked, no check engine lights on.
View 9 Replies
