Ford Super Duty (1999-2016) :: 2002 F250 - Misfiring Under Heavy Load Or High RPMs
Aug 12, 2015
So basically I thought it would be a great idea to degrease my motor from the top down.... After washing I start it up and drive down the road to head abunch of misfiring under heavy load or high rpm's.
My problem is that the misfiring won't throw a code. I then proceeded to buy a new ignition coil (thinking this was the problem) but with no code to go off which cylinder was bad I just switched the good ignition coil into each cylinder and starting it.
Up each time. None of them seemed to make it better. Also the injectors all seemed to be good. So what to do ?
2002 Ford F-250 5.4l
View 3 Replies
Advertisement
Best truck I ever had but around 200k would occasionally blow a bunch of smoke when pulling a heavy load.
My 2000 f 350 xlt triton v8 has done the same thing a couple times (about 200k miles).
The (cough) "truck expert" at my local dealer has never seen that before but its happened in 2 different trucks for me. It never caused a problem other than scaring me.
I sold the 02 last year when i got a 2011 f 250--it was 12 years and 300k miles old and never was hospitalized except for a fuel pump due to my negligence of filter.
View 1 Replies
I have a 2000 f250 crew cab short bed 7.3 on a 6inch bds lift and 37 inch tires. When I accelerate pretty much any load above 1200 rpms I can feel a vibration, kinda feels like it may be coming from the front left but I'm not sure. I have heard that a wheel bearing going out can cause this, would this maybe be what's causing it?
I thought wheel bearing because it kind of sounds like there's a howl when decelerating, probably when accelerating as well but the trucks too loud and I can't hear it. or also have heard motor mount gone bad, I've also heard ujoints but the ujoints were done this summer. the front ujoint is bad but the front driveshaft shouldn't be turning when out of 4x4 and hubs unlocked.
View 4 Replies
I have a 2002 F250 CCSB Lariat 4x4 with the Triton V10, I'm up to 232,000 miles so far and fairly happy with the old girl. Just this weekend, I noticed some hesitation when at idle and even more rough running when under slight load. The misfire/hesitation is worst when going up a slight hill, when the truck is accelerating at low RPMs.
I am getting zero trouble codes or freeze frame conditions on my scanner. What should be my order of diagnosis? Vacuum test at line from PCV to TB, COP test? EGR inspection? Plug inspection? Also, how do you test a coil if resistance is not a reliable method?
View 5 Replies
I have a 2000 SD F250, gasser, auto. Last week I pulled a heavy load and developed a tranny fluid leak. The fluid appears to be coming from what looks like a freeze plug on the bottom of the casing forward of the (torque converter?) pan . Is that plug easily replaced by a DYIer. Small leak. 150K on the motor. First time it has leaked. Heaviest load I've pulled.
View 2 Replies
I am having overheating problems at high speed/high rpm/under load. The only codes ive gotten are EGR dpfe (0401). Truck is 99 f250 with the 6.8 new egr valve, dpfe, new coolant, new thermo, new sensor under manifold. I blew 90 lbs air pressure thru the egr lines, big and small, they were clear.
So whats left? I never hear my fan clutch......should I? I've had other trucks and the fan roared when first started for a few seconds, and then again when you were hot...they really roared.
Is it possible for the egr port where it goes into the throttle body to be plugged? guess I should've checked that when I had the egr off. Would an aux. fan be a waste of time?
This is pulling a 3500 lb camper trailer up moderate hills.
View 11 Replies
I just changed out my IAC. Truck is still idling too high. When I squeeze the host to the IAC it idles down. When I unplug the IAC the truck immediately dies.
Does the IAC talk to the the Throttle position sensor? Should this be my next part to change?
2002 F250 5.4L ....
View 4 Replies
Is there truely no cure for exhaust flutter on a 2002 f250 V10, bedsides putting on headers??? I have the the sound at shift points around 1800-2200 rpms. Sounds great before and after these points....
View 14 Replies
1999 F350 7.3 Super Duty surges when going uphill with a load. The only time we drive it is when towing the horse trailer - also has a camper on.
The truck doesn't physically surge, just the RPM gauge goes up and down and along with it a humming noise.
Also, What conditions should I engage the towing button on the end of the gear shift? I've heard several answers. Should it be engaged when towing or off?
View 2 Replies
Is there a steering stabilizer for a 92 Ford F-250 custom 2wd? and what's the difference between a f250 custom and a f250 heavy duty?
View 2 Replies
I just bought a 99 F250 Super Duty with the V10. When I bought it, I knew it had 2 misfiring cylinders (4 and 10) because it was throwing P0304 and P0310 (only 2 codes), but wasn't concerned as I've had to take care of my wife's Escape with it's misfiring cylinders. I replaced the 2 coils and replaced the plugs with Motorcraft plugs from O'Reilly's, cleared the codes and she ran fine for a couple of days. Now I'm getting an intermittent misfire, it's only occasionally throwing a pending code of P0300 which is "Multiple Random Misfire".
I'm fairly certain it's an issue on the electrical side because if it were an issue with the injector or injectors it would be constant regardless of RPM... right? As it is now, it basically does it between 55-65 while in overdrive trying to pull a hill or slightly accelerate. Once it's shifted out and the RPMs go up to 2k+ it runs like a champ... and it kills my fuel economy. The way it's behaving is just like when a coil is bad, but it's saying it's not identifying a specific cylinder (saying it's multiple) and it doesn't always do it (about 60% of the time).
I checked the MAF and it's very clean (looks almost new), checked the vacuum lines (those I found without a manual) and couldn't find any leaks and when I changed the plugs all the plug wells were dry.
View 6 Replies
I have a 2009 f250 with 5.4l 3v. have had the truck only about 6 months. it started missing about a month after I got it. I replaced all 8 cops and all 8 sp. The truck ran excellent until 11/29, then I got a cel and the truck started running really bad. Found 3 misfiring cylinders. Changed all 3 cops again and that did nothing. Pulled the injectors and found 2 of them were clogged, replaced those also. Still no change was told by someone that the ecm/cpu may need to be reset, did that also. Still no change. There are no codes present but still has the multiple misfires.
View 9 Replies
I have a 06 f350 with 5.4 140k miles. Recently it has been shaking bad on idle but only in gear and it's hard to start when cold. The exhaust is moist at all times and the fluids never leak. When you floor it it hesitates feels like it's overly rich but if you let off a little it stars to pull again. Also while cruising at 1500-1700 rpms in any gear it will surge and skip. Only time it will miss and the CEL comes on is over 4000 rpms for a random misfire. Just put new coils in new fuel pump and filter. There has always been a cat code but it never effected the drivability. Could it be injectors?
View 3 Replies
I have a 99 f250 that seems like it has a bad coil, under a load it starts surging or bumping ( like it has in the past and I found a bad coil), I went through and unplugged each coil one by one while idling, couldn't find a bad one, so I bought a new coil and went through and rotated the coils, nothing worked, no check engine lights on.
View 9 Replies
Just bought a 1999 7.3 f250 w/71000 miles and took it to a diesel guy and under load he said that the whistling was normal..is this correct?
View 3 Replies
I have a 2012 F250, 6.2L, Crew Cab, FX4 with a little over 77,000 miles on it. I bought it used from a Ford dealership last summer. Prior to now, I've only had one issue with it and that was squirrel/rodent induced. Something chewed through the wiring harness right before the connection to the #7 cylinder. There was enough left over wire to solder it back together and put heat shrink around each wire.
It ran fine up until last weekend. The wife and I went to a store, she was driving and parked like a total jerk right in the front area of the parking lot. When we got back in the truck, she started it up and it was just running rough with hardly any power. My first thought was someone dumped something into the gas due to her amazing parking, but there were no smells or residue of anything near the gas cap when we got home only a couple miles away.
When I got home I ran my code scanner and found 300, 301, 305, 307, and 308. I dumped a bottle of ISO-Heet in it, let it sit for a bit then cranked her up and ran it for a few miles to the gas station and filled up...about 25/26 gallons, I don't remember...I was a little above 1/4 tank when this all started. No change in performance and the codes were all still the same. I pulled the MAF, it looked clean, but I wiped it down anyways and threw it back in. No change. I then changed all the plugs. This took care of 301 and 305 but 300, 307, and 308 were still coming up. I then picked up two new coil packs for cylinders 7 and 8, threw them on and still no change.
I sat with it running on a flat surface for a little while revving the engine randomly for about 15 minutes, during this I noticed a fast tapping noise at about 3400 RPM, it went away quickly with no changes in the gauges on the dash. I cant really tell where it's coming from, but kinda sounds like its under the middle of the truck. While sitting there I ran the codes again, and now its back to 300, 301, 307, and 308. I'm now at a loss of what to even look at...
I've also checked the voltage coming off the harness at the connector to the coil packs...just under 11 volts. I've searched all over for what that voltage is supposed to be, but have failed miserably in my searches.
View 6 Replies
About 20 miles into it, and it starts cutting out on me under load, over about 1/4 throttle. I baby it a ways further, and park at a wal-mart. Idles fine, but once again, after 1/4 runs like crap, acts like it's back firing through the intake spit and sputtering. Have the wife come pick me up since I was heading to work. Decided to shut it off, and restart, and it acts like its never had a problem.
Was messing with it today, and let it warm up in the driveway. Once it got hot, same story good 1/4 throttle, past that, not so much. Shut it off, started it back up and drove it to see if there's any codes at vatozone. Drove good (laying into the throttle) for about 2-3 minutes, back to same behavior. Hooked up code reader, no current codes, and no historic codes. Although I did notice (actually since I bought the truck) that the check engine light never comes on, even at initial start up. Looking at my spare cluster, it's an l.e.d. So no bulb out I guess unless the led is bad. Truck has around 130,000 miles on it. Everything is stock.
I'm leaning toward a fuel pump, a clogged cat, or a fuel pump relay or cutoff switch problem.. It doesn't have any other issues than that, and has been a good truck for the 10k miles I've owned it... 2003 F250 5.4...
View 7 Replies
I have a 2001 Ford F-250 5.4L V8. 117,000 miles. The problem I have been relentlessly trying to diagnose is a slight bucking that occurs under load when the truck is in overdrive. When the truck bumps up to higher RPM's it is fine but when it is around 1500-1700 RPMs on the highway it does a small buck like I'm hitting a bump in the road. I know there are many threads on this but none of them have gotten me any closer to a resolution. It also seems to have a bit of power loss when accelerating. Things I have done so far.
-Spark plugs and COP replaced about 1000 miles ago
-New fuel filter
-Cleaned MAF sensor
-Cleaned throttle body
-New PCV
-Seafoam treatment in gas and through brake booster.
View 14 Replies
My 2008 f250 6.4l just got out of the shop a week a go new small block and new pistons, throwing #1 constrabution code,map sensor and #1 cil misfire you can hear air come out of the intake, I am guessing valve train or lifter..... other problem two days after the truck throwing the codes i went to take it to the shop and would barely drive floored struggle to go 10mph put it in park rev up normal will go in reverse normal just no power in drive, no transmission codes, had it towed to the diesel shop, mech said might be a fail safe on transmission from the engine codes? it has egr/dfp h&s mini maxx tuner, the truck has 170k on body 11k on new engine before the new block that was put in last week.
View 6 Replies
Just bought this '08 F250 CCSB 4X4 5.4 Problem is the steering seems heavy, it tends to wander at higher speeds and won't return to center after a turn. I've searched on here and found a few possibilities (axle u joints, ball joints, steering gear, etc). I have an appointment with the dealer on Friday to fix it under warranty but he is convinced it's the u joints in the steering shaft seizing. When my F150 steering shaft began to seize, it would be hard to turn then break free then be hard then break free and this is not what is happening on the SD. I haven't had a chance to check the front end myself but not sure how you would check the axle u joints if there was no play in them. How would you check to see if they were seizing up.
View 3 Replies
I have a 2008 6.4L F-250 and occasionally when I come to a stop I can see a faint white smoke coming out from under the truck and the hood. The smoke has a heavy diesel exhaust smell. When I step on the pedal nothing comes from the exhaust and it does not happen all the time. What is going on?
View 2 Replies
