I have a 2002 F-250 Super Duty 4X4 triton V-10. Where the security control module is located? my keyless remote system does not work even after programming a new remote. The Ford dealership charged me an hour labor to diagnose the problem and they said it's the security control module which I just ordered.
View 14 RepliesWhere is the SYNC module in an '11 F250?
View 3 Replies2009 F250 Super Duty 4X4 auto lock hubs not working. Indicator lights on dash come on but will only go into 4 wheel drive when hubs are locked manually. Vacuum is present at lower of the two vacuum lines when engine is running. I attach the lower line to the module, rotate switch to 4X4 high or low and module doesn't allow vacuum to reach upper nipple. Which fuse operates this module?
View 3 Replies02 f350 5.4L Where is the body control module located?
View 1 RepliesI have noticed my trans temp gauge needle is dead center of the gauge even on a cold start. I thought my sensor was under the pan so I pulled it and did not see any sensor at all. Is there a external sensor?
View 5 RepliesProblems with the Parking Assist/Reverse Sensing System. I have found the troubleshooting that everyone has done very useful. I have a 2007 F350 Lariat Crew Cab with problems with the Park Assist. Whenever I put it in reverse the system shuts off( Off Light illuminates). I have checked the wiring harness and all connections, Parking switch, and Reverse Sensors. I have done everything except check the Parking Assist Module. My maintenance DVD tells me that it is located behind the glove box. I cannot find it in there anywhere. Where it is located. The trucks manufacture date is June 2006....
View 14 RepliesTruck is an 02 F250 Automatic 4X4, 7.3 PSD.
Cruise control will turn on, will sometimes set speed and sometimes will not. If it does set and work it may kick off at any second or it may run fine. I have noticed it seems to kick off mainly after going over a slight bump in the highway or it may just kick off for the hell of it. Truck has 50,000 miles on it, I bought it new. Also having trouble with the throttle position sensor, it seems to have a "dead spot" at about 58 mph that shows up when I romp down on the pedal to pass on 2 lane roads. Can these two symptoms be related? Both are very aggravating. FWIW it does have the power adjust pedals. Truck is 100% stock, no power chips or other upgrades.
I have a 2002 F350 7.3 Powerstroke with approximately 200,000 miles. Recently I have been having an issue with what I am told is my airbag control module heating up to the point it is too warm to touch when I am pulling a heavier load. It is located just under the dash on the center hump. I removed the black plastic cover revealing the module itself in order to determine that indeed is where the heat and smell of hot electrical equipment is originating from. It gets too hot to touch when pulling a heavy load and making the motor work...once I lighten up on it or am not pulling it immediately cools back down. If it is an option I would just disconnect it but I havent yet for fear of creating more of a problem.
View 1 RepliesI have been trying to hunt down the issue with my 4wd. I have thus far done the following:
- Check and clean all fuses under dash
- Checked the underhood relays
- Check for proper operation at switch
- Opened relays under how and manually switch them, transfer case motor and lights on dash work as they should.
So my though is that I have power going everywhere. Something is not sending the signal to the relays. I would narrow this down to the 4wd control module behind the glove box. Is there any way to test this for sure? I'm about ready to just buy on and slap it in. Spending way too much time on this issue.
I need to replace, its either a brake pressure sensor or speed control deactivation switch . Would like to know which it is and can I get a generic one from other auto parts beside a ford dealer Can post a pic of part as soon as I figure out how to do that exactly. 2002 f250 super duty....
View 8 RepliesMy father-in-law has a 2008 f-250 with the 5.4. as he was driving a while back all the gauges of the dash quit. The engine still kept running without any noticeable difference but when he shut the engine off and tried to restart, it wouldn't even crank but the security light was flashing. He tried starting it again a few hours later and it started just like normal and ran fine.
He has had this problem occur several times in the last few months, but the other day it repeated the problem again and would not restart for about 5 days. He has tried charging the batteries, changing relays, checking all fuses and finding none blown, scanned it with his code reader, and checked the steering column for bare or rubbed wires.
2010 F250 Lariat, cab and a half, PSD. 5600 miles.
Sunday I started the pickup and received "trailer brake module fault" in the message center. I wasn't pulling so wasn't too concerned - hit the reset and continued on.
Sunday night I started the pickup again and received the same message followed by "check brake system". I also lost illuminated gear selection, the traction control active symbol was displayed and the traction control "off" (PB) was illuminated. After several attempts it reset, everything returned to normal and I was able to get home without incident.
Monday morning it wouldn't start. It indicated "trailer brake module fault", "check brake system", traction control active and off, no gear indication, the odometer indicated "-------" and it did not react to the key in the start position.
Tuesday morning I attempted to start and it was the same as the previous attempt. I noticed that the theft prevention appeared active (flashing) so I removed the key, locked the doors, unlocked the doors, tried again - no joy.
I kept trying while holding my mouth in different positions and finally by the grace of God it fired. I delivered it to the dealer.
The dealer called yesterday afternoon and reported that everything is a result of a bad trailer brake module. The new one is to arrive today, they will install and everything will be peachy.
I asked if they could just unplug it and reprogram the truck to believe it never had one - the service writer said it can't be done, different piece parts on trucks with or without trailer brakes.
I really have no choice but to push the "I believe" button and carry on but I am slightly concerned. The fact that the trailer brake module can cause catastrophic failure doesn't seem too cool, I don't have a real warm and fuzzy feeling associated with venturing far from pavement, reliable communication or alternative transportation.
In the meantime I suggest that no one take "trailer brake module failure" lightly.
2009 Ford F350 Diesel ....
I am trying to find my ABS controller because I have an intermittent ABS light on the dash and the code says something about signal loss on more than one wheel. So I assume I have bad wiring or a loose plug somewhere.
I found this (pic attached) on the left hand side under (or a little behind) drivers seat mounted under truck on the frame rail. I think it is the control module but when I tested wiring I found no continuity to any of the ABS wheel sensors.
Is this the control module?
Trying to find ground wire location on my 99 f250 super duty with the 5.4 triton I didn't unbolt it myself. Going to be doing the big 3 upgrade soon and would like to use the factory ground spots.
View 13 RepliesMy 2005 F250 started stuttering, lurching, having wild swings in rpms, nearly dying at stop signs, no pickup when stepping on the gas, then taking off like a bat outta hell. After reading many, many posts here and on other sites, I have concluded that the most likely culprit is the ICP sensor, so I picked one up today (along with a EBP sensor - another story). It appears from the many posts that I have read that Ford/Navistar have frequently changed the location of these sensors. My question is: Where are the ICP and EBP sensors located on the 2005s (actual manufacture date is 07/2004)?
View 6 RepliesI have a 2005 f250 with a 5.4l 3v. Where the pcv valve is located is it in the valve cover or attached to the intake and what does it look like? I have pulled the hoses off both sides but I have not found it let.
View 3 RepliesWhere to find the PCM 4 digit code on 2001 F250 superduty/v10- Lariat?
View 3 RepliesI have a 1999 ford f250 superduty extended cab and am trying to find possible subwoofer locations (not wanting to lose floor space) but I can't find any pre-made boxes. Any pictures I can use as reference. Really wanting to install subwoofers. What can I do?
View 10 Replies2006 F-250 'family Cadillac' ... Where exactly is the door buzzer? I am looking all around under the dash but can't find it. I want to disconnect it.
View 13 RepliesWhere this box is located?
View 1 RepliesWhere this sensor is? I am trying to mount a front bar and need to know if I can drill thru the tube behind the bumper ( this is the one that is right behind the plastic trim piece.)
View 2 Replies