I have a 2002 ford f250 superduty and when I have my headlight switch set to auto to come on when it gets dark they will for awhile and then my headlights will turn off for no reason.
View 2 RepliesI have a 2002 F250 diesel, the key will turn to acc. but not on. It feels like it is hitting something in the column. I tried moving the shifting lever back and forth with my foot on the break, as I turned the key but it would not turn. I am thinking the tumblers are OK because it goes into acc. It feels like their is some lever that is not releasing the shift lever, because if I turn the key hard the shift lever jumps. What is wrong, or how the interface between the lock tumbler and the shift lever works?
View 4 RepliesI just replaced the head lights on my 2001 f250 it had the sealed beam one-piece glass headlights and I replaced those with regular headlights and when I went to get bulbs I found out after I get home the connector is different from the new bulbs. the new bulbs fit correctly but I can not hook plug them the plug has 3 connectors that have two connectors level and one is higher than the other two and the new bulbs the three prongs are level.
My question is. is there another bulb that will fit and plugin and if so what is the part number? is there a adapter that I can get that will allow the factory plug to work? or will I need to cut the old plug off and splice a new connector on?
I bought an hid kit for my 2005 f250 the dog lights work fine but the headlights won't stay on. They come on for about 30 seconds then shut off. How to fix this. I've swapped the ballast with the fog light ballast and it does the same thing.
View 3 Repliesi have a 2002 f250 i drove it lat night parked it came home from work at about 3 and noticed my head lights were on and just headlights. I open the door and see that the switch is in the off position too. WEIRD HUH ? they wont go off. I tried to unplug the switch and nothing.
View 6 RepliesOk i have a 99 f250 with a 6.8 v10 that is not turning over at all. I have checked the battery and its good. I have replaced the starter and the starter relay and have tested the starter and its good too. I have also used a volt meter on the batter, starter, and relay and looked at the relevant info and they are all in the correct volt range. I have also taken the starter off and looked at the flywheel and it has good teeth so thats not an issue. I am completely stumped now as to what it could be?
View 5 Replies2009 F250 lariat. While driving down the highway my wipers came on when stalk was in the off position. They would not shut off. Had to remove the relay to get them to shut off. Also, during middle of a sunny day the headlights would temporarily come on and shut off when it was in the automatic position. They would not come on if I put it in the off position though. Since both the wipers and high beams are part of the multifunction switch is it likely that the switch has gone bad vs. a more major issue with the computers. No other issues identified.
View 1 RepliesI just bought a 2004 f-250 checked everything out except for the headlights ... when I tried them the didn't work except on flash to pass ... I searched around and found some possible solutions and tried them .... first I checked the bulbs and all the fuss they are good then I bought a headlight switch ....that fixed the problem for about two days then they quit working again... so I took it back and got a new one ... when I first put it the new one in it didn't work then it started working a day or so later and I hadn't done anything to make it work... then a couple days later it went out again ... I have swapped the switch out several times and have had no luck I replaced the multi function switch and still no low beams ...
All the fuses are still good I have checked the wiring visually as much as I can see and see nothing... buddy of mine checked the pins on the headlight switch connector they are all good .. Read something last night about a guy whos alternator was going bad and caused his not to work checked mine its putting out around 13.4 at idle .. is there a relay somewhere ... my book doesn't show the function of any of the relays so I don't know ...not a mechanic but a pretty decent parts changer. Trying to fix this myself . Next week have to take the truck to pull the camper ..
I have a 2002 F350 V10 and one night I turned the headlights on and when the ignition switch was turned to the off position the lights would go off. When the ignition switch is turned off the lights come back on. I changed the ignition switch but the problem still exists.
View 3 RepliesMy trouble is upon turning key to start everything goes dead (no power to anything). Does not always happen, sometimes she starts just fine.
After the power cut out if I turn key off, wait a minute, then back to on position she will sometimes come back as normal or sometimes the on "ding" will chatter and dash lights will be dim.
I have checked batt connections, starter/solenoid connections, block ground connection. All seems fine. Get same problem when I jump starter with screwdriver. Been suggested to me ignition switch to blame.
I have a 2004 f250 with some front end troubles. When turning right once in a while it will make a hard CLUNK noise and then trying to drive down the street it drifts over to the left and I pull the wheel back to the right and when I turn the wheel it feels like I like theres something hitting somthing else in the front end. I have checked ball joints and tie rods and they are all nice and tight. Some stuff I have done that probably isn't related to my problem is shocks and sway bar end links. What this could be? Hopefully not the steering box!
View 7 RepliesMy 01 F-250's wipers would not shut off. As soon as the key was turned on they would come on. No delay but high and low only. Had to pull the fuse to drive it. I replaced the multi function switch as well as the relay with no fix. I did some reading on this problem and it is related to the "park" switch in the wiper motor itself. I took the black plastic cover off the motor which reveals the worm gear driving the plastic gear which acts as the switch.
The contacts for this switch are hard to get to as they are on the backside. I blew compressed air into every little crevice and removed most of the grease. I regreased and put it back together. Sure enough the wipers work just fine now. I am assuming the compressed air trick may be only temporary. Need to reveal the contacts for the park motor switch without destroying the plastic housing?
Headlights work well w/ ignition switch off. High/low/passing all ok. When I turn the ignition switch on, there's a strange wheezing sound for a second.
When the ignition switch is on, there are no headlights.
What's the wheezing sound? Why does the power to the switch quit with the key on? The more I work on modern trucks, the more I like my 1968 f-250.
I have a 2000 F250 SD with the V10 engine. The problem that I am having with it as of late is that whenever I perform a full turn I hear some clunking coming from the front end. The clunking is similar to that heard from cars that use CV joints FWD but of course it sound more "manly"
Anyways, my truck has the full axle on front so I suppose it could be either the u-joint at the hub or the hub itself. I would like some pointers so I can acquire the required parts.
Have an 03 f250 6.0L and the tie rod from pitman arm moves easily and there isn't a steering stabilizer, noise got worse after I put new tires on front but it's a loud clunk that I can feel. I've replaced the sway bar bushings and end links. Would the worn tired rod make that noise or would it be ball joints?
View 1 RepliesI have a '16 F250 4wd with the 6.7 and approx 3k miles. There has been a strange sound coming from the front end when turning left from a stoplight. It sounds like something slides or shifts and it only happens once in a while. The noise isn't loud but you can feel it.
View 2 RepliesJust bought a 2002 F-250. Truck came with 18" Rims with 275/70/18 tires. The turning radius is awful, almost unsafe. The stock rim and tire size should be 16" rims with approximately 265/75/16 tires. Would the larger rims have that big of an effect on turning radius? I have owned two 2006 F-250's, and they turned nothing like this truck. I have not really gotten into the front end to see if the stops have been adjusted and/or if the tires are hitting.
View 10 RepliesI bought a 2004 F250 Crew Cab LB 4x4 with the 5.4 Motor and when I turn left it has some Tight Spots and I can't figure out why, I checked the Drive axles to make sure the locking hubs were unlocked and they spun freely, I Also have a lot of play in the steering wheel, Could this all be Related to the Steering Box? What else should I check for ?
View 3 RepliesOnly got a click when turning key, in Park or Neutral. Made sure I had >12.4V from battery. Jumped starter solenoid with a remote start switch across main power line to starter and the 's' post, crank pulley almost moved, but didn't rotate. Removed belt, all pulleys rotate, but could not budge the crank pulley with a short breaker bar/socket, rotating clockwise from front. Removed starter, that upper bolt is a super pain! Not even sure I'll get it back in. Jumped starter solenoid again on the bench using a battery and jumpers, not the best connections, starter hesitated little bit, but opened up fully a few times, so I'm thinking it's ok (even though the power line from the solenoid to starter motor needs re-taping). Tried rotating flywheel from starter hole, no good leverage point, but no movement. Before I re-install the starter, how much torque should I be putting on the front crank pulley? Some say it should move easy enough cause the starter isn't that powerful. Others say remove the spark plugs to reduce compression? This truck is new to me, so I unfortunately have no history.
View 1 RepliesI had some steering issues with my truck so took it for an evaluation at pep boys. They recommended a new steering gear box and tie rod that hooks to the pitman arm so I had them replace them. Steering was improved but now the wheel is canted to the left or right depending on when I make a turn. When I make a left turn, the wheel is canted about 10 o'clock. When I make a right turn, it's canted about 1 o'clock.
I looked under and had my brother turn the wheel and didn't really notice any thing loose. I lifted the front and noticed the left wheel bearings need to be replaced. I also noticed the shocks were shot and replaced them but it didn't make a difference in the crooked wheel.
Do you think it's the wheel bearing that can cause this? How about the ball joints? The truck has 407k miles and I bought it a month ago. Previous owner said he never replaced any steering components. Should I just replace all steering components with the Moog kit? I'd like to hold off on the $600+ kit for now as I just bought a a boat and the boat needs some stuff. I hope to find that one thing (hopefully not more) that's loose.
2002 Excursion 4x4 7.3. I've read about this on here before but I've forgotten what the problem is. When the wheels are turned and the vehicle is going forward at some speed, there is a knocking sound, like a ba-doomp ba-doomp ba-doomp. Does it in both directions, sounds like its in the front hub area. I don't have the time to fix it myself, how much should I expect to pay a dealer and/or independent shop to do it?
View 2 Replies