So one day my 4 wheel drive just stopped working, when I put in 4hi nothing same with low, the light on the dash doesn't even pop up and it doesn't engage. I've done about everything I could think of doing besides replacing the motor for it and the wiring, I hate getting stuck...
View 4 RepliesLove my 03 lariat Super Duty, King Ranch. Just found out 4 wheel drive is not working. Checked fuses, next going to look at the vacuum system, make sure its working. New to the Diesels but going to work at it and learn at the same time. 2003 F-250 4x4 ....
View 5 RepliesI recently picked up a '99 F250 Super Duty with the 6.8L V10 for a song.
The 4 wheel drive hubs are not working with the vacuum. If I use the manual lock on the hubs all is well. I ordered the Innova 31703 CarScan OBD2 + OBD1/ABS/SRS Scan Tool. It says it does Trans codes. I am hoping it will cover the 4 wheel drive too.
Maybe related, the heat is always on. Meaning I feel heat at my feet when the temp dial is cold and fan is off. I can't find the heater control valve to check the vacuum line.
I purchased the truck used last summer and this is the second time I've put it in 4wd. The first time was over the summer, and I had a hard time getting it into 4wd, and it made a "clunk" sound initially but drove fine, then went back into 2wd just fine and had driven fine ever since. Today I put it into 4wd, no clunk or any other noises, very smooth, but it drove very rough, almost as if the wheels were out of sync or something. It seemed almost like the wheels were breaking on and off on their own, very weird. When I put it back into 2wd, it did that for a few seconds until it went away. I only drove it in 4wd in my parking garage as I didn't want to risk any more damage to it on the road.
View 14 Replies1999, F250, SD, v10, Auto, 4x4.
My light on the overdrive is not coming on and the overdrive does not seem to be working. I had a new transmission installed a few weeks back. Wasn't working prior to this.
Checked the EOF vacuum lines and pump but still have a problem. The EOF works and locks the hubs when I switch to 4x4 high, Easy to feel when you turn the wheels but it will not go into low. The light on the dash does not light up the word "low".
View 1 RepliesI have a 1999 f250 7.3 ... l extended cab 4x4 super duty ... ABS light on, over drive light flashing and speedometer has stopped working .. I have replaced abs senor on the rear of transmission and on the rear end.both new and just replaced abs module just the computer not the pump that was used . And abs light, overdrive light are still on and the speedometer is still not working ..
View 14 RepliesI have a 2006 F250 Super Duty w/ turbo Diesel. Took to dealership for "hopping" feeling when turning sharp. Was told that 4 wheel drive solenoid was bad. Where this solenoid is located? I know I can fix but want to know where it is located.
View 6 Replies2012 f250, fog lights stopped working and tried fixing yesterday. I'm getting 12.8v at the plug but as soon as you plug the light in it goes to 0. Ran a new ground from frame and the hot from plug and still nothing. High beams off, truck running and switch pulled out. Bulb is fine, hooked it straight to battery and it comes on. I though it was a faulty ground but by running a separate ground and still nothing. I'm at a lose.
View 2 RepliesI have an F-250 diesel 2004 and about six months ago it started acting really crazy. Basically most all of the dashboard electronics stopped working like the speedometer , odometer, gauges, etc. additionally all of the interior lights, and the radio stopped working. Now it looks a lot like the attached picture when I'm driving the truck. All of the lights are lit up on the dash panel but nothing actually works. I thought at first that a bunch of fuses might be blown but I have replaced nearly every fuse that has anything to do with any of the affected systems. What the issue might be.
View 11 RepliesI have a 2003 F250, 4x4, 5.4L and today my fuel gauge stopped working. I don't know if it had anything to do with a stall, I was on an exit ramp and the truck cut off, I quickly restarted and no issues after that. Other than the fuel gauge not working at this point.
I looked at the fuse panel diagram and there is no fuse for just the fuel gauge. The only thing I see is #35, instrument cluster. The rest of my instruments are working, so what else would cause the fuel gauge to stop working? It had a little over a half of a tank before the stall, after the stall it went down to less than half. I filled up shortly later and it's just stuck at less than half.
A buddy of mine has a 99 F250, and the 4WD stopped working. The 4wd light in the dash does not turn on with the key with the rest of the lights. There is a Low Range light that does turn on. He took it to a shop/dealership and they said the vacuum was good. They also swapped in a different GEM module, which didn't change anything.
I swapped the relays under the hood - no change. I keep reading that there is a two wire plug on the transfer case I can test for voltage or to manually power the motor. Where is it? I see two plugs - the blue one on the left has 4 wires, the black one has more. Or is that not the shift motor I need to be looking for?
My door locks stopped working new battery in fob, I can hear them trying to work. 2000 f250 crew cab .....
View 3 RepliesMy drivers window will not work at all but when I push the button I get a clicking in the fuse box. The other 3 windows partially work but will only go up or down in small increments. I have tried holding the button and slamming the door and this allows the other 3 windows to work. I thought it was the switch so I replaced it and that was not the problem. Fuse and relay seem to be fine. If it was just the driver window I would think it was the lift motor but with the other 3 windows on the fritz I have no clue.
View 1 RepliesI'm hoping this might be a "quick fix". Got in the truck the other day and my power driver's seat had no function what so ever. Not a big deal for me as I drive with the seat all the way back but the complaints are starting from my wife so it's time to find a fix.
This is the first F250 I've had so the wiring is a little new to me. I checked the fuse panel and the fuse seemed okay I swapped #9 out for #22 as they are both 30A and I don't need the trailer at this time but still no luck.
Are there any other systems tied into the driver's power seat, any wiring harnesses I should check or perhaps a fuse that is not shown in the owner's manual? My truck is the 2013 Gas F250.
2002 F250 SD 4x4 crew cab, v10. 4x4 not working. Replaced switch on dash, not the problem. Some of told me it was the vacuum control module. Not sure where to start.
View 4 RepliesI have a 2002 f250 4x4 this snow plowing truck and going to be a pain if i cant figure this out before winter sets in. number 34 fuse (10amp) blows when replaced. cruise stopped working and can not get into gear from park after starting but turn ignition switch to 1 click forward and put into nuetral then start and go on about my business? Cruise recall completed in 06, brake lights work horn works.....
View 7 Replies2002 f350 7.3 diesel automatic. The cruise stopped about a 1/2 year ago and i have done the recall and replaced the steering wheel switch. but it still doesn't work. the horn works and speedometer works.
View 4 RepliesI have a 2001 F250, 5.4, 4X4. My ignition key stuck in the start position and when I pulled it back to the run position, everything seemed ok. As I started down the road, my speedometer stopped working and my overdrive light was flashing. Also my turn signals had stopped working and my A/C clutch didn't engage. Figured I burnt a fuse. I looked in both the under dash and power distribution box and all seemed well. I checked the fuse for the turn signals/flasher and it was fine. The flashers worked. Thought I might have fried something so I replaced the ignition lock and switch. Also my service engine light came on throwing a code for the vehicle speed sensor.
Looking for solutions on this forum and the internet, I learned that the turn signal switch could have gone bad and the VSS sensor is on the top of the rear dif and an easy fix. Well replaced the sensor but nothing changed. So I went back to the fuse box. Examined every fuse, big and small and I found a 10a with a small space. This was #24 under the dash. From the manual, "#24, 10A, A/C clutch, Blend Door Actuator, Trailer Tow Battery Charge Relay Coil, Four Wheel Anti-Lock Brake System (4WABS), Turn Signal." Replaced it and everything went back to normal. Turn signals work, A/C clutch works, no flashing overdrive light and speedometer works. All from a 10A fuse. If you have any of these symptoms examine all the fuses carefully. There's a 20A fuse for turn/hazard lamps and this other one buried that's only 10A.
My father-in-law has a 2008 f-250 with the 5.4. as he was driving a while back all the gauges of the dash quit. The engine still kept running without any noticeable difference but when he shut the engine off and tried to restart, it wouldn't even crank but the security light was flashing. He tried starting it again a few hours later and it started just like normal and ran fine.
He has had this problem occur several times in the last few months, but the other day it repeated the problem again and would not restart for about 5 days. He has tried charging the batteries, changing relays, checking all fuses and finding none blown, scanned it with his code reader, and checked the steering column for bare or rubbed wires.
I just bought this truck and for some reason sometimes the power windows and radio will not work for awhile then it will start working. I replaced the relay on the accessory and I still have power to the dome lights and instrument cluster. I am kind of at a stand still on this matter. I have read that there is quit a few problems like this and not very many explanations to resolve it.
View 5 Replies