Ford Super Duty (1999-2016) :: 2002 F250 - Carrier Bearing Removal And Vibrations
Jul 14, 2014
I started with removing the two bolts that hold the carrier bearing to the crossmember that attaches on each side of the frame, well the clip that basically would hold the "nut part" of the bolt on the top side sheared on both of them due to salt+calcium chloride.
It felt like there was a 6 point head up there so I tried fitting wrenches and sockets up on the other side, I finally got a good hold with an 11/16" wrench but it just kept rounding more and more. Normally I would just torch the heads off but the gas tank is right next to it.
Any tips for getting the carrier bearing bolts out now? I don't care if I destroy it they're easy to replace. Also I'm typing this from my phone so Incase my sig doesn't show this is on my 02 f250 crew short bed 4x4
View 2 Replies
Advertisement
So, my 2004 F250, CCSB, Fx4, 6.0l, truck broke the carrier bearing today. There is an annoying hum that modulates, the drive shaft has a lot of play and there is light visible at the top of the bearing. The problem is that it broke on a 550 mile trip to Franklin, TN and I need to make the return trip. Is there anything catastrophic that can happen running it this way?
View 14 Replies
I am looking to replace the carrier bearing and (u joints while I'm in there) on my 08 F-250. I do not have access to a lift so this will be done while on the ground. Am I asking for trouble by doing this on my back?
View 14 Replies
2002 F250 4 wheel drive manual hubs, 7.3....
My first thought was to have the tires rebalanced and rotated to see if it is tire noise? I am hearing damage on top of the noise from the 7.3, hard to be sure!
View 11 Replies
Need to replace the ac compressor bearing/pulley on my 2001 f350 7.3. My question is do I need a special tool like a pulley puller or is there another way to remove pulley? I already have the clutch assembly removed as well.
View 1 Replies
I have a 2000 F-250 SUperduty with a dana 50 front end , and as most of you know the front hub bearing's are junk, and expensive to replace. I know dynatrac has a kit to convert it to the tapered, cheaper, servicable bearing's. But 2g is a lil out of my price range. I was curious if anybody has tried takin the knuckles and stub shafts off an older dana 60 and putting the knucke's on the front axle to get the older bearing style instead of the hub bearing and the actuall lock outs instead of the POS vaccum style.
View 4 Replies
I dont want to pry on the wrong thing and brake something. I am trying to remove the headlight. I was told that their are some pins that need to be pulled up. I dont see any pins. I do see two plastic clips on each side of the headlight. They are flat on the top with a small slot in them. There is a "T" stamped on the top of it. Are these the pins? I tried to find a shop manual today without much luck. Looking for a picture to show the pins that need to be removed.
View 7 Replies
I own a 1999 F250 super duty and have the front end apart to service the u joints , I noticed that i have bad axle stub needle bearings on one side. I was wondering what is involved in taking those out and replacing them, it looks like they are held in place with some type of spanner nut. My next question :Would it be worth the cost just to replace the whole bearing hub assembly? The truck has 134000 miles on it.
View 10 Replies
I am working on my Dads 01 super duty with a 5.4, automatic, and the pinion bearing has seized up due to a lack of fluid from a rusted out rear diff cover. The tag on the diff cover had a 10.5 stamped on it and has 12 bolts. Is this known as a ford 10.5"
I have changed gears and pinion bearings in a Dana 70 before is this the same process? What are part numbers for a new pinion bearing and seal? Gears are in fine shape.
View 2 Replies
So I have to replace the front unit bearings on my 2004 f250 4wd. My question is, which thread pattern I have, fine or coarse? I have read that the early models, 99-02 have coarse threads. Afterwards they are fine. I am going to order online as they are cheaper than the local parts store. I have the Timken part numbers for either thread pattern.
View 4 Replies
1999 F250 CCSB Lariat 5.4, 2 wheel drive. I plan to replace the Driveshaft Center Bearing in the next few days. What size is the Nut that I have to remove to remove the yoke next to it so I can press the bearing off?
View 4 Replies
I am trying to replace the ball joint on my 2008 f-250. Does the hub assembly come off of the knuckle or do you remove the whole knuckle and hub assembly together? If you have to remove the hub assembly what is the best way?
View 14 Replies
I have an 2003 F250 with a nosiy alternator and need to change the bearings. I would like to have the bearings on hand before i take it apart. What is the part numbers for the bearings I need?
View 3 Replies
I have a 2008 F250 5.4 4x4 supercab long box (68,000 miles) that has a little bit of movement in the front wheel bearing and hub assemblies. Made it through inspection OK but it will need to be changed soon. Just asking for everyone's thoughts on brands they prefer. I have had great luck with Moog brand products in the past. I put SKF hubs on my wife's 2010 Explorer and they I would say are top quality also. Not interested in a conversion kit or cheap junk. I want a good quality unit. What brand has everyone had good results with? Are Moog or SKF the way to go?
View 8 Replies
Well, I've been meaning to get to servicing/re-greasing the front hubs/bearings for a while but somehow it keeps getting moved down the list.
2000 F250SD 4X4 Gas Manual Hubs+Trans
I'm currently going through the many threads that turned up in my search query.
Driving slow with the windows down it seems like a low whine or squeal coming from the left front. Tone changes when working the steering wheel left and right. Haven't detected any grinding sounds. Any other techniques for isolating the problem? It's going up on jack stands tonight and I'm going to see if there is any wobble from the front wheels and I'll listen as I turn each of the front wheels. Oddly, the right front hub is hard to turn. Left front turns easy.
Viewed Rob259956's videos on servicing the hubs. Currently researching accessing the wheel bearings. It seems pretty straightforward. Truck has been off road but not mud bogged or anything like that. I'm guessing a bad bearing will be easy to identify as will a bad o-ring but any other stuff I should look closely at?
View 6 Replies
I have a 2001 F250 Super Duty 5.4 Triton motor with a Transmission Leak. I have drained the Transmission, replaced the Transmission pan gasket and filter. The auto parts store also had me purchase the Torque Converter bearings/seal along with enough transmission fluid and a bottle of Lukas Transmission fix. Do I really need to replace the bearings/seal if I have everything else already ?
View 2 Replies
I am needing to replace the front hub wheel bearing assemblies on my 03 F250 4x4. I know Ford changed the studs from coarse thread to fine thread in between the 02 and 03 model years. Mine has a build date of 08/02 and I haven't been able to find the exact date they switched over. I'm ordering the parts online and want to get it right the first time.
View 3 Replies
I want to know if there are any issues when removing the rear block, also do I have to put a new block in or can I just leave it out ....
View 12 Replies
I tried searching and googling but came to no results, unless its like similar trucks. How do the 4x4 shift remove? I have an 04 F250 and someone decided to put the shift on sideways so the 4HI and etc read upside down before I purchased the truck. Do I just rip the thing off?
View 1 Replies
I would like information how to remove the rear seat back on a 2012 F250. I want to remove the head rests and from what I can find out they are bolted solid to the rear panel. I asked the same question earlier and got a reply for 2011, would that be the same? Is there any place I could get a schematic, a picture is worth a thousand words.
View 5 Replies
I have a 1999 F-250 SRW 4x2. Is there a post that explains how to remove the front brake slide pins?
View 3 Replies
