Ford Super Duty (1999-2016) :: 2002 - 4x4 Not Engaging Only Light Came On
Sep 6, 2013
I have a 2002 Ford Superduty. I recently had installed a BDS 8 inch suspension lift. I also had the upper and lower ball joints replaced. All this work was done by a certified garage. Today i went to pull out my boat from the ramp, turn the switch inside the cab to 4x4 high. The light came on but 4x4 did not engage. As i pulled the boat out of the water the rear tire spun in the sand but the front did not. As i cleared the ramp and on level ground i turn the switch off and back on i heard not but the light can on. With the 4x4 light on i turn the wheel and pulled forward i noticed no hopping as when a truck is in 4x4. Initially when i turn the 4x4 switch on i hear a clunk up front but not after. Drove home drive train appeared fine no noise.
View 3 Replies
Advertisement
My 4x4 on my 2000 model f350 will not engage. The light works, comes on briefly on startup of the engine. When I flip the switch nothing happens. When I jumper the relays nothing happens. I do not have the factory hubs, they r warn hubs and the vacuum line to them is capped off. How to figure this out on why the 4x4 will not engage?
View 13 Replies
2012 6.2 XLT 50,000 miles with manual single zone controls. I haven't had time to work on it yet, but it seems that my AC compressor is not engaging. The dash controls light up normal, fan comes on, etc. I am just looking to see if there are any common failure points. I know it COULD be low on charge, clutch could be bad, etc. I am just checking if there is a common failure with these trucks AC system.
View 10 Replies
Pump works fine. Replaced pvh. Won't go into 4wd hi or lo no matter what I try. Even with them in lock. How do I know if hubs need replaced or just hub locks?
View 2 Replies
2004 Ford F250 CC 4x4 6.0L
Took the family down to the beach today. Had some tough sand to get across in a few areas to move away from the crowds. Got a little dicey and the truck got stuck in 2WD. Switched to 4WD but back tires kept spinning. Couldn't figure out why and the truck started to dig deeper in the sand. Got a little nervous and I didn't want to start the day off with having to get pulled out.
Got out of the truck, locked the hubs in manually and I was out, no problem. Left the hubs locked until we left the beach and back on pavement.
What might be the problem and why the "shift on the fly" switch on the dash didn't seem to engage the 4WD? I even tried to switch into 4L and back to 4H (truck in neutral, break pedal compressed) and still no workie. Only manually locking the hubs would engage the 4WD.
View 14 Replies
Truck was running fine up until now. After the WTS light goes out, I crank it and.... nothing. It doesn't even try. It's not a battery problem. I have 12.6 V from each battery before and after cranking. The lights are bright, the horn works, the dash lights are strong and bright all both before and after cranking. It just doesn't want to engage the starter. I tried my backup key as well, thinking it might be a problem with the PATS. No dice. Where to start looking?
View 6 Replies
I'm trying to figure out why my auto locking hubs do not engage. To isolate the problem shouldn't the hub engage if a vacuum is applied to that hub only? A solid 18 inHg is maintained at that hub for over 10 minutes but the selector will not rotate, which suggests to me the seals are OK. What then might be the problem?
View 13 Replies
2006, ESOF. Noticed the front hubs aren't engaging but the transfer case is. What should I check?
View 3 Replies
this morning my 02 decided to turn the ABS light on, and start bouncing the speedometer. plus, the OD light is flashing when stopped with foot on the brakes, but the trans is shifting fine.
nothing changed on the truck except almost 3 inches of rain fell last night.
will AE tell me if the VSS is going bad?
View 6 Replies
I recently bought a 2002 F350 and so far, the only issue I've had with it is I can't find out why the ABS light is on. I've looked around and found that it's probably caused by the speed sensors. But this is where I run into issues. From what I've seen, a bad sensor will generally give a reading of 0 ohms, but none of mine do. The rear diff sensor gives me ~1800 ohms, which I believe is OK.
The front driver side reads about 700 which is I know is a little lower than it should be, and then my passenger side reads ~42 mega ohms. Both the front sensors kind of threw me off since what I've read says they should all read about 1200-2500 ohms. Any other things I should check or should I just go ahead and replace both front sensors? I've just looked around and have barely been able to find anything about the front sensors.
View 2 Replies
Just completed the rebuild on the front end of my 02 f350 and of course I had to take the abs sensors out, everything is good but now my abs light is on. Is there a method I can use or do i have to hook it up to scanner and erase the code.
View 1 Replies
had a problem with their OD light blinking and shift problems. This past week my od light started blinking and when I shifted into drive, it was stuck in overdrive. When I shift into 1st it would go to 2nd and stay there. So basically I had 2nd and overdrive. I started replacing sensors like the VSS, and checking the wiring warness. Took it to a transmission garage and they told me it was toast. Then I decided to bite the bullet and buy a new tranny. After replacing the tranny it did the same thing with the same codes showing. Then I got smart and checked the fuses. Of course it was as simple as a blown fuse causing all the trouble. In my truck it was fuse 23 under the dash. A 20 amp fuse that was listed as engine control. Im not saying that in every case if the OD light starts blinking it's as simple as a fuse but in my case it was, so lesson learned. Always check the fuses first.
View 13 Replies
Got in my truck this morning and everything worked fine, no problems. Arrived at my destination and parked. Come out about two hours later start the truck and my A/C wont blow air, My truck is an 05 lariat so it has the climate control A/C. Everything was working fine it just wont blow air, When i turned the A/C on and off i could hear/feel the small thump of the clutch engaging on the compressor. I am thinking the blower fan just went south? or maybe something stupid that controls the blower fan? Summer is in full swing here in central florida, temps are 95+ not including the humidity...
View 14 Replies
My 2011 F350 is not engaging 4wheel drive from the dash switch. When I turn it to either hi or lo it says "shift in process" but no 4 WD. It will engage manually from the hub lock, no problem. I know very little about 4wheel drive but am otherwise mechanically knowledgeable.
View 5 Replies
I have a 2001 F250 4x4 and the ESOF switch not engaging hubs, currently I have no 4x4 lights coming on in the cluster when i turn the switch. I am not experiencing any of the vaccum symptoms that most people are suggesting. I When I turn the switch i also do not hear any relays clicking. Relays have been tested, and i waited for the 45 second transfer delay that the manual mentions. ESOF switch has power, and is working properly (I know because I bought a new one in attempt to fix the problem) Basically I have no responses from any of my 4x4 indicators or parts.
View 14 Replies
I have a 2000 f250 CCSB 4x4 with the ESOF auto hubs. The auto hubs won't engage automatically. They work fine manually. The transfer case is engaging and correct lights are coming on. There is a little bit of vacuum coming from the vacuum switch but it doesn't seem like much to me. All the dash HVAC controls work fine though. I Lubed and cleaned inside the hubs according to Guzzles directions.
While torn down, I blew through the vacuum port on the outside of the hub and there was little to no restriction. I don't think there is enough vacuum to pull the hubs, but is that possible if all the dash controls work fine? What pressure should it take to engage them? My next step is to pick up a vacuum pump and see if I can engage them with it.
View 6 Replies
Parking brake light stays doesn't come on when the parking brake is engaged. The light DOES come on when starting the vehicle and the gauge cluster cycles through its start up procedure. Couldn't find a fuse that would fix my issue...does one exist?
Truck is an '02 F250 w/ 7.3TD and 6 speed manual.
View 2 Replies
My 2002 f350 diesel recently started acting up, the first sign was when my park brake light came on and the chime came on. I mucked around with a few things but still wont go away, while I was doing this a buddy noticed i had no brake lights at all and under further inspection no signals either, not even the clicking noise you usually hear also the cruise control has stopped working as well as the little screen mounted to the roof near the rear view mirror. I am fairly clueless with electrics (I don't even own a multi meter) but i do want to figure this out, i have noticed that fuse 20 was burnt and after replacing it it pops pretty much right when i push my foot on the breaks or signal.
View 10 Replies
My buddy has a 2002 F350 CC Longbed with a 7.3. Last night the overdrive light started blinking. He said he drove it today and it takes about a mile or so for the light to come on but then it is a steady blinking. Truck has about 254K miles on it. He said other than the blinking light everything seems normal. How to figure out what this issue may be?
I got AE hooked up on his rig.
When I pull (ALL) codes this is what I get:
When I pull (Current) codes I get this:
I tried to clear the code and the light stopped blinking, but he said it started blinking again on the way home.
View 2 Replies
2002 F250 SD 4X4 5.4L. 4.5 inch pro comp lift tire size 305/75/R16. K&N cold air set up. 208,000kms
I know the truck does horrible on gas but lately is been getting worse, maybe I am getting 350km to a tank. Mixed highway city driving. Sounds like I might have a vacuum leak somewhere but I have no engine light. I've had the truck since last year and put about 10,000km. on it done regular oil changes .. brake maintenance no motor work so far.
View 2 Replies
Today I purchased a 2002 f250 GAS super duty 5.4. The first thing I've noticed wrong is: The driver door doesn't lock with the remote control but the passenger door does. I also noticed: when I shut the driver door, the dome light comes on and stays on but when i open the driver door, it shuts off (as if something's reversed). Do you think these two situations are related, and how can I fix it?
View 9 Replies
