Ford Super Duty (1999-2016) :: 2001 V10 - Sudden Power Loss After Sitting In Long Traffic Jam
Jun 26, 2015
My excursion suddenly lost power after sitting in a long traffic jam. I have a scan gauge II set up and didn't see any signs of over heating however when I went to accelerate back up to highway speed my motor revved up to 3000 rpm and just lost power I ended creeping on the side of the road at about 15 mph and barely maintaining that. The motor was not willing to revv up. I reached a spot to pull over and shut it down for about 15 minutes and started back up and drove off with no noticable issues. I have 211,000 miles on this motor and I am going to change my coil packs, I think they have been there since the truck was sold new....I changed four of them to address a miss and have six left, I will also be changing my fuel filter. We are about to pull our camper across country....about 1400 miles..
View 5 Replies
Advertisement
I have a 2001 f250 super duty extended cab with the v10. Over the past week it has been running fine and it will all of a sudden lose power and dies. I've been able to start it back up once right away and a few times it started up after a few hours of messing with it.
So, after the truck dies it will crank and crank but will not start. We have checked fuel pressure and nothing. Then we applied direct current to the fuel pump and it turns on. Then we applied direct current to the fuel pump slot in the fuse box and got a fuel pressure reading of 40 psi. But when we crank we have no pressure.
When we apply direct current to the fuel pump slot in the fuse box the truck will only crank and not start.
View 11 Replies
Last night was getting down to freezing. I drove out of my buddy's driveway, stopped to close the gate behind me, put it in gear and started to drive away, about 5-10mph. I left off the gas as I rounded a gentle curve, then got back on the pedal as I exited the curve. All I got was a revving engine, as if I was in neutral. Checked to make sure I was in gear, and same result. I stopped, engine running, and put it in park, and then back into gear. Nothing. Drive, low, Reverse nothing. I did see the rpm change slightly. engine runs normally.
No fluid loss, no mechanical noises indicating something breaking. No weird smells. Fluid level is as good as I could read on that crappy trans dipstick. Truck ran flawlessly up until that moment. the transmission is a BTS with about 100K, so I'm fairly certain it's not the mechanical diode notorious for that year. My problem description does not seem to fit the failed diode anyway. I did run across a post that better matched my problem description and that was the transfer case motor. I have 4WD, but was not in 4WD at the time.
View 5 Replies
I am trying to diagnose a problem with a friends 2002 f350 7.3L truck. the engine has approx. 140,000 miles and is all stock, no programming or aftermarket parts. Anyhow, he said driving down the road the other day the engine all of a sudden lost power and the truck wouldn't go any faster than 45mph. he said taking off from a stop sign, the truck has no power and takes forever to get up to 45mph. after this issue began, he has changed the fuel filter & screen, air filter and fuel pump. The check engine light if OFF, no active fault codes.
View 1 Replies
On the highway doing 100 mph. during af take over, my Ford F-250 6,4 Super Duty 2008, lost nearly all power. (now it is like driving my old hummer h1)
Engine and car runs/starts great, only 10 minutes uptil 60 mph. now.
My mechanic has given up. He checked following:
EGR = OK
HOSES = OK
ERROR CODES = NONE
INTER COOLER = OK
PARTICLE FILTER CLEAN = OK
TEST WITHOUT EXHAUST = NO DIFFERENCE
FLUIDS = OK
Hopefully something I can fix with my hammer. The car has 85.000 miles on the clock.
View 14 Replies
The last couple weeks my excursion had started to have a stumble and smoke white ate the first startup or after I let it sit for a long time. I did get progressively worse. I noticed the hpop line to the driver side head was leaking from the fitting so I rebuilt the boss fitting and now it's not leaking but when I started it up this morning it did the same thing.
If I give it throttle it clears up pretty quickly but if I let it just idle it will put white for probably 5 minutes. I have no codes showing when I looked with the scanner I don't see any other oil leaks and I don't smell a fuel leak.
View 6 Replies
My 2010 F250 V10 120000 mile has a sudden loss of MPG. It usually is around 12 MPG but now I'm at 8 I checked the air filter and its clean I checked the tire pressure and there all up to pressure. I'm probably going to try the fuel filter next.
View 2 Replies
Got a 2001 7.3 crew cab long bed over the winter and over the last week I have some electrical issues.
Leaving work I had a dead battery(s) or so I though. first though the batteries are going or the alternator going. Its a manual so i had a friend pull me to bump start it and everything was as it should. The volt gauge came right up and checked the alternator and it was OK.
Later on while driving the radio turned off and I could not get it to turn back on. At the time I didn't notice if the other cabin accessories were working
(didn't think to take notice). So, turned around a drove straight home. Once in my drive way I shut the truck off and right away turned it back on and the radio came back. I didn't know what to make of it so I just let it be.
The next morning I went to start the truck, Wait to start light went out and when I turned the key. Just a click. and the instrument panel goes dead along with all the other cabin power. when i open the door the turn signal starts clicking. So I took the batteries out (thinking that something is staying on inside the cabin and draining the batteries). I charged them at work came to find that they are holding a charge.
My issue was most definitely the GEM. So i took that out sent it to Florida and got it serviced. When got it back today and ........Same thing. I am at a loss here. Am in looking at the right things? What should I be looking for?
[URL].....
View 3 Replies
My truck is 2001 F250 with the 7.3 I have AFE intake, TS 6 position chip, Stage 1 Auto Tranny, 4in Exhaust all the way down. New glow pugs as of last week as well as uvchs and gp relay. Also has a new hpop line. New compression sleeves for fuel lines, riff-raff fuel banjo bolts and fuel pressure regulator.
I am having a hard start issue no matter what the temp is outside, unless it plugged in. Once it starts its good unless it sits for more than 5 hours.
Batteries have tested good, glow plugs ohm at 1.3, gpr 12.83 at batt side- once on it 11.9. All fuses are good. HPOP res is showing at about 3/4" down from top.
***Wires going to the MAT sensor are showing through at the connector, not sure if this could be a problem...if so why???
****Noticed some oil in the ICP, cleaned and unhooked will check start tomorrow to see if this works with long start as truck is plugged in.
Will also be putting a new fuel filter in and double checking oil level in the am. I do not have a scanner tool and am doing the best I can before I take it in to ford to diagnose.
View 1 Replies
So I was traveling thru the grapevine on the 5 Fwy and no problems. Made it to the top didn't over heat. Then all of a sudden it lost power. Pulled over and it stopped running. Won't start. Fuel is pumping, I took off the fuel filter and turned ignition on and it filled up.
View 2 Replies
I drive an 08 f-350 with 120k no tune or deletes..(yet). I was driving home yesterday when I all of a sudden I have a lack and power. I then notice i have no boost at all. I heard an exhaust leak and instantly checked my boots on inter-cooler pipes....
After farther inspection, the bolt fairy came and I am missing some bolts on my up pipe where it meets turbo. Is this break in vacuum system the reason I'm having no boost? What is easiest way to get to up pipes without removing cab? Where did the bolts go? I got to get this fixed because I need truck to get around town.
View 5 Replies
One of my work trucks is a 99 F-250 5.4L. Up until recently it's been running strong. Then one day it's like someone flipped a switch, and now it runs like it's losing power.
Symptoms: a quick short stumble when you first hit the accelerator. While driving, it takes the entire pedal to accelerate. Even with the pedal to the floor, it won't keep up with traffic. Driving uphill, it will barely maintain 40 mph.
I've checked everything I can think of. Fluids and filters are all good. Battery and alternator are good. There are no trouble codes. I have Autoenginuity with the Ford Bundle, and the truck passes every diagnostic test I throw at it.
There's no smoke. It still idles pretty smooth, although there is a slight and very quick random shudder in the idle that has started at the same time it started losing power.
Transmission is good. The last thing I tried was to change the fuel filter, but that made zero difference. Quick question, does the tank on the 5.4L trucks have a pickup screen like the diesels? If so, I might try blowing some compressed air through the fuel line and see if it dislodges anything.
So that's where I'm at. It has no power, yet I can't find a single thing wrong with it.
View 14 Replies
I have a 99 F-250SD with 5.4 automatic that just all of a sudden started running unevenly at random times, but frequently. There is a pending code P0300 Random/multiple cylinder misfire. I have had the truck for 12 years and it has run perfectly for the last 10+ years and just started this problem, it did not come on slowly but all of a sudden. I have seen on here that some people say that 90% of the time a PO300 is a bad cop. I replaced the plugs 60k miles ago when I had a bad coil on plug 10 years ago that did not set any codes, but this seems very different that more than one cylinder seems affected, like maybe 2 or more cylinders are not firing momentarily.
There is a big power loss momentarily while it happens, but doesn't happen for long. The fuel pressure stays pretty constant (30 psi at rail) even while it happens, and it can affect the idle as well as while accelerating or cruising at speed. I cant imagine more than one coil on plug would be skipping at the same times or fail at the exact same time, but maybe having only one bad cop could cause this much hesitation? Does the code that indicates random/multiple cylinder misfire rule out only one bad cop? It just seems like running on 7 cylinders wouldn't be so noticeable. Could a sticking egr valve cause unevenness at idle and higher rpms and set a P0300 code? Would checking manifold vacuum be they way to see if egr valve is not working correctly.
View 11 Replies
So I'm not sure if I bought a lemon, but i picked up a F-350 6.4 Turbo Diesel two days ago and the check engine light came on yesterday. It's giving me a P0088 Code as well as the P0088pd. It's got 131,000 miles on it so no warranty will cover me.
I'm tracking the TSB put out telling the techs to replace the HPFP, but they mention a loss of power. I've only had the truck for two days, but I've driven them for work before and I can't detect any loss of power. Besides the code, everything seems to be running fine.
What can I can try out before running out and changing the HPFP? I'd rather not cut so deep into my savings if I don't have to.
View 6 Replies
Last night, I left it running while unloading a trailer and come back to notice it was idling abnormal. I jumped in it and tried to move it and there was a noticeable loss of power. I unhooked the trailer and tried to get it home. I only made it 1/2 mile down the road when it started spitting and sputtering (surging ever now and then) to a level that it died completely. I was able to start it back and get it out of the road but had to be pulled into a drive. It got to a point it wouldn't start back at all.
Today it started up however still had a rough idle and really has no power to speak of. The more I messed with it the less power it seem to have.
I have searched the forums and tried these things:
1) Checked the oil and noticed it was on the low end of the operating range. I put some in it to put it back to normal.
2) Disconnected the ICP
3) Changed the crankshaft position sensor
4) I dumped the fuel bowl after it completely died (in case it had any water in the fuel bowl).
The fuel filter was just changed 2 weeks ago. The fuel pump seems to be operating correctly (or it at least refilled the bowl) and started again with a very rough idle.
It doesn't have a engine light on nor do I have anything to read any codes it may be showing.
View 14 Replies
I have a 2004 f250 superduty. I lost all electric to truck. No lights, radio, etc. Turn key and no click or dash lights. I put a charger directly to battery and nothing. Is there a main fuse in power line prior to the fuse box under the dash??
Also, right before this happened, I went to start my truck and my batteries were low, the truck turned over a few times, started dying, so I turned the key off, and the truck kept turning over on its own, as if the circuit remained closed for ignition due to low battery, and it turned over by itself until the battery was completely dead. But putting my battery charger on it now gives me no electric at all.
View 5 Replies
Truck sat for 1 1/2 years. Changed filter and put in 15 gallons of fuel. Had maybe 1/2 gallon old fuel in tank. MAYBE. Fixed fuel line because it wasnt getting fuel and it fired right up and idles great.
Truck has no acceleration over 2500 (or so) RPMs but idles fine. This is depending on how hard you push the pedal of course.
If you drive the truck normally like a grandmother it seems to be ok. As long as you dont need a passing gear or need to accelerate more than 1/4 pedal
If you try to push the pedal to get the next higher gear it will sometimes hit the gear fine. IF you floor the truck it will totally lose acceleration. Then the truck will run like crap even slow for a good while. But then it will clear up for the low end. Then you can drive it normally. Then when I think I can test the upper end I get the same thing again.
View 14 Replies
I have a 2004 F250 Super duty that had a battery die (I left the keys in the ignition switched on overnight) and after jumping the battery off the vehicle started up but now I have no power door lock or window functions. Any reason a dead battery issue might affect the power locks and windows?
View 10 Replies
I bought 08 6.4 113000 on it 4x4 lariet drove 300 miles home. No problem 2 days later runs fine for 45 minutes than loses power and sputters up hills starts no problem every morning every time wait awhile sometimes runs fine was on e when test drove canged both fuel filters oil and drained 8 quarts tranny fluid and replaced it. When problematic rpms wont go over 2 turbo psi seems high seems in sync with rpms dropped...
View 3 Replies
2003 F350 6.0L ... 171,000 miles ... 5,100 since oil change 15W-30 at the shop ...
I was driving on the interstate (50 miles of driving) struggling to maintain 70-75 mph at 2,200RPMs. I would accelerate and RPMs would go up to 3,000 but no speed. Before I could pull off speed slowed to 50 before dying. Sat on the side of the road 30 minutes before I could get it started. Had to give it gas. No misfires just quietly started. Couldn't go over 30 mph. Towed it to my destination 135 miles.
Volts on 7Pin FICM read fine.
Checked the fuel fulters. Air Filter. Tank for debris. Nothing.
My coolant reservoir was lose and I noticed a lot of coolant in the driverside front wheel well and down the left side of the undertruck. Reattached after checking FICM. Hope that was all it was cause I couldn't find any leaks.
I had Planned to have the oil changed before the return trip before this all happened. New to Diesel engines but I like a challenge. Where do I go next?
View 3 Replies
I have an early 03 f350 with a 7.3 liter 298,000 miles on it
Replaced fuel filter
New oil change and filter replacement, New icp sensor .
Deleted the baffle and installed a cone air filter with the air sensor installed in the neck .
I Was driving home one day and the truck just slumped into this huge power loss . Couldn't get over 2200 rpms and barely made it over 30-40 mph.
Truck in park - idles like crap and still won't go over 2200 rpms when holding the pedal to the floor . And it has what sounds like a miss at a struggling "full throttle" (22-2500) rpms - thought it could be my icp sensor - replaced it -- no change
Checked driver side wiring harness -- no damage chafing found -- did a fuel can to pump test no difference - and today after I reinstalled the fuel line right after I ran my can to pump test I let the system prime . Started the truck and it ran for about 40 seconds and died and wound not fire back up and would just miss and spit and sputter -- lots of gray smoke though- but it fired up a few hours later after I let the batteries sit on charger .
Now before all this happened - I noticed the truck had a bit of a gutlessness to it as I would be piddling around around town and it would have this hesitation in power kind of like a slight jerking feeling , now this truck was so gutless since the day I got it ,I couldn't even burn out on a gravel road without the throttle going limp and the check engine.
Light kicking in so I figured I'd give it a bit of hotshots secret and see if It would maybe flush the injectors but it really made no difference...
View 7 Replies
