Ford Super Duty (1999-2016) :: 2001 V10 - Blown Head Gasket?
Feb 17, 2015
Back Story: Ok so in my infinite wisdom I let myself get distracted when I was looking at an 01 F250 V10 Crew Cab. I thought, it needed all new breaks/rotor & 2 calipers. And new carpet and seats, then I would have a good hunting rig.
So I went and looked at the truck in the dark (first mistake). The guy was very honest with me and told me about all the body and interior issues. Even informed me of the caliper that he disconnected because he could not afford to fix it. He informed me that it did burn a little oil and it's been a while since he checked the oil. Well at that point I was going to look under the oil cap to check for any milky residue. Well I got distracted (Second Mistake).
So here we are 2 weeks after getting bringing the truck home. I already replaced the carpet and seats, breaks & rotor & 2 calipers. Well today I decided to go get some new oil and a filter, and do a quick oil change since who knows when it was done last.
Issue:While draining the Oil it seemed like there was an abnormally large amount of oil in this engine. (See photo of bucket full of oil from this rig.) Well didn't think much of it and swapped the filter. And went to add new oil to the engine and found that under the cap was some milky substance.
The V10 has 420K original miles. I have heard that is no big for the V10 but thought it would be good to note this detail. Questions I have: Should I get some kind of test kit to confirm it's a blown head gasket? If so what kind of Kit should I look for? Do you think this truck is worth replacing the head gasket?
Any chance this may just be a known issue for the V10 and I just need to replace some kind of valve? I could not find any you tube videos of a head gasket replacement on a V10 any thoughts where I should look?
My Skills: Just to be clear I don't know anything about the V10 motor. I have a 94 f-250 but have never had to dive in to a head gasket replacement before. I have done a head gasket replacement on smaller engines (IE: car and a jeep) but those were obvious that they had a bad head gasket.
View 10 Replies
Advertisement
2005 FORD F350 Lariat 6.0, 61,000 miles, and in prestine condition. Just got the news the head gasket is blown! HOW DID THIS HAPPEN?!!! My mechanic says to scrap the whole engine because the 6.0 is the worst engine around. This truck should last for years!!!!!
View 14 Replies
how difficult is a in frame head gasket repair?
View 6 Replies
I've been trying to figure out what is going on with my '99 F-250 V10, you can check out this thread for the back story
[URL]....
I did a compression check and the results seem inconclusive to me- see image.
Before I did the compression check I started to take the intake manifold off to change the gasket set and it's about 50% done. I'm at a crossroad now. Do you think I should finish switching out the intake gaskets or do you think it's more than likely a head gasket? I would hate to put it back together, it still smoke and have to take the intake and everything else back off to do the head gaskets.
Someone had mentioned a possible small crack in the cylinder wall that is closing up when the engine gets heat in it and obviously doing the intake and cylinder head gaskets would fix it if that's the problem.
View 14 Replies
I thought I needed a head kit my truck runs and drives great till I run out of coolant no smoke doesn't get hot I run out of coolant I lose my turbo. Pull over fill it up I'm back to normal I just noticed I have sweat marks on my water pump pulley.
View 6 Replies
2001 Ford F250 5.4 gasoline. At the most recent oil change my mechanic said there was an oil leak and he had dyed the new oil and cleaned everything up and to come back in 100 miles.I just did so and he said that it was a leaking head gasket. He said to do the head gasket replacement right or to put in a rebuilt engine would be close to same and he would recommend the replacement. He said it was not a heavy leak and probably ok to drive another 10,000 or so miles first. Just returned from a trip where we drove 15 hours straight (30 degree temps) and the truck ran fine and no overheating.There does not appear to be oil in coolant or vice versa. I took the cap off overflow coolant and cranked and revved and no disturbance whatsoever. I read somewhere where a mechanic was saying it was impossible for this Ford engine to leak oil from a head gasket failure .
View 7 Replies
Have my oil leaking-passenger side head gasket replaced (along with the drivers side for preventative measures).
To ease my mind at such an expensive repair on a truck I just recently bought, I was wondering what else gets replaced with this repair.
Obviously the head gaskets along with head studs, coolant and oil, but anything else? valve cover gaskets? intake gasket?
View 14 Replies
To all those folks that said I had a head gasket putting pressure into my cooling system and causing it to overheat, you were right. It is a 2003 F250 with 80000 5.4 l. I have had to replace mexhaust manifold bolts on left side (horrible job, couldn't get one out). Back fenders are rusted out, under the extended cab rusted, doors are rusting at the bottom. My friend/mechanic said it was time to get rid of it. I don't really have thousands of $$ for a different one, but also, replacing the head gaskets are in the thousands for a repair bill. I have looked at used 2008 250 4 door and they are 20000+++ sheesh, but a new one is out of the question. Do I get the gasket situation repaired?
It does not act up all the time, some times it never overheats, sometimes it will. Somewhat infrequent ( I had one mechanic look at it and he tried 3 different times, and it did not overheat. Temp gage will peg, coolant resevior will overflow, but is not hot (100 degrees). I dont have the really have the money to put into a newer model, but I am worried about being nickeled and dimed to death after dumping a couple of thousand into a head gasket, plus I suppose I need to have the other side manifold gasket/bolts checked too. It seems like low miles to be having issues, yes I realize all will rust, but this year, as evidnet in our area, was really suspect-able to rust.
Not worried about the body, is it worth it to spend 2500 for head gasket repair, or trade up a couple of years, less miles, etc. My worry is, I already had to fix 1 exhaust manifold gasket, know head gasket to fix a cooling issue, do I cut my losses and move to another truck, or spend the money for repairs. I don't really have money for either but want to make a good decision. Truck has not been abused and has been serviced as scheduled. Had to put on new brakes and rotors, as would expect, and ball joints too. Oil looks fine, no contamination, and coolant is clear. Will the head gasket get worse? As I said before, it is intermittent, but I don't trust it for long trips.
View 9 Replies
I am replacing the head gaskets on a 2006 Ford F250 6.0 .... I have heard that I should replace the head bolts with studs. Do I torque the studs just like the bolts?
View 5 Replies
my truck at 210k miles got a new radiator (seeping at seams), thermostat, water pump (bearings shot, leaking), intake manifold (The crossover was leaking). It now has 227k miles. Oil leak in rear at head gasket by starter (bad head gasket?) It overheated the other day( blowing coolant out the expansion tank needle in the red) Replaced thermostat. Drove around for two full hours, seemed fine, Drove to work today it overheated ( same thing, blowing coolant needle pegged) didn't make it to work. There are no external leaks and its not putting steam or white smoke out the exhaust. I read somewhere that a blown head gasket could make the truck overheat, is that possible? What all could cause this problem?
View 6 Replies
After replacing most of the underside of my Super Duty, Complete front end, backing plates, brakes, rotors and shocks, I have a misfire code on cylinder #4. I replaced the plugs, cleaned the MAS and filter and rotated the coil to cylinder #1. Still have a misfire on #4 and noticed the coolant slightly low and some condensation on the oil cap. Could this be the intake gasket? My mechanic is away for 2 weeks and I think the price at the dealer will kill me. I have 63K on the truck, don't tow and plow mostly family members. It's getting a little rusty but is still in good shape.
View 13 Replies
So I've put about 1000 miles on my 03 F250 since buying it, and just the other day it's started leaking from the rear of the passenger head gasket. Enough to drip on the driveway and exhaust, and have some exhaust smell. 126,000 miles, 5.4
I've checked with my local ford dealer, and It also needs passenger exhaust manifold and studs, so the dealer price to tack that on would be a whole lot more too since there are already a couple studs broke. It would be best to get it done when the head is pulled.
I've checked with several local mechanics, and none of them are interested in pulling the head on this engine. That has me concerned about doing it myself too..especially since it fits in my garage with only a few inches to spare..
View 14 Replies
On July 18 my 1999 Ford Windstar van was towed and diagnosed with a blown head gasket. I FINALLY got it back on Sept 4th and was told it was idling a little rough, but it was probably due to water that got in the catalytic converter and would work itself out. The next day we drove it about an hour away it was idling VERY rough and started to stall every time we came to a stop or tried to slowly pull into a parking spot. The following Monday September 8th it wouldn't start and the shop came and towed it back in. It's still there and they are saying they aren't sure what's wrong with it, but are assuring me the problem is unrelated to their repairs. Every time I call they continue to say they are working on it. Where do I go from here?!?!
View 10 Replies
i have a 06 explorer with the 4.0 V6. 4x4 XLT with 106xxx miles. i just bought this thing back in January. of corse, i didn't get an ext warranty. well the past couple months its been loosing power, its got a stumble and seems sluggish. its losing water. no water in oil, no oil in water, don't smell coolant in the exhaust. yesterday i went out and looked and found at front of head on pass side at front cyl, there was coolant from head gasket down the block and also in the valley of the block. i started the engine and once warm, everything was dry. shut it off after about 20 minutes and still nothing wet. this afternoon the only wet spot was in the valley which was dry after running yesterday. is there anything else i can check before tearing it down? with the water in the valley, it looks like it could be coming from the thermo housing.
View 6 Replies
I have read all I could find on replacing a blown head gasket and and after absorbing everything that TigerDan posted on here, I dove in and began. After disassembling all the topside junk I finally got the intake manifold loose and got down to the head. I began undoing the head bolts and found two broken bolts. The head won't budge so I am calling in a cherrypicker. I don't know what kind of mess I'll find when the head comes off. I assume the head will be warped or the block may be damaged.
View 6 Replies
I have the same problem as the gentleman w/ the '97 4x4 4.6. Intermittent overheating. The water pump and t-stat have both been replaced, as well as the radiator. Some one told me a piece of gasket material from the heater core may be floating around and periodically clogging things. Could this happen? and what's the fix? Also, someone told the guy w/ the 4x4, that he could have blown head gasket, and to perform a sniffer test to find out.#1. What is a sniffer test? #2. If the head gasket is blown, wouldn't there be water in the oil?
View 4 Replies
Truck is a 2006 F-350 6.0, ARP studs, Ford Head Gaskets, Bullet Proof Diesel Oil Cooler Kit and EGR with an SCT tuner on tow mode.
Towing approx 15,000 pounds noticed truck started to lose power and misfire. Pulled over and noticed engine oil all over the driver side on engine, looks like it sprayed to top of engine as well. Oil on valve cover, FICM, exhaust manifold. I looked under the truck and saw that oil is all over bottom of the truck, differential covered in oil as well. Looks like blue smoke coming from tailpipe and smells of oil burning. Cannot tell where oil originated from.
I removed the EGR Valve, to see if there was moisture on the valve and when I looked into the intake manifold there is engine oil pooled in the bottom of the intake manifold and on the EGR Valve.
This is not dirty water from soot, it is oil. Truck is misfiring, with no codes being thrown. I noticed a small amount of white residue around the radiator cap however I had just filled up the reservoir, week prior. I unfortunately do not have gauges in the truck and rely on the factory gauges; coolant temps did not rise or move at all when this happened. I am not sure if I blew a head gasket, and really confused on how engine oil got into the intake manifold. I ran the engine with the air filter removed and can see blue smoke coming out of the CCV and oil in residue in front of the turbo inlet.
View 11 Replies
My 97 f150 5.4 started missing on 5,6 it had antifreeze on top of the spark plugs but i cant figure out where its coming from my truck has been loosing coolant and it seems like the system is holding pressure because every time i take the cap off the radiator overfill i can hear it hissing then i see the antifreeze level plummet there's no visible leaks that i have seen when the truck is running an missing it steams out the exhaust but when its no missing it doesn't seem to be there's no milky oil or anything the thermostat doesn't seem to be leaking either the truck has over heated a couple times due to the antifreeze disappearing or the temp wont move at all then it shoots all the way to hot and cools down within seconds to normal i just put a new thermostat in. Also it sometimes misses on 4 and my exhaust smells like straight gas i put 4 gallons in it got 29 miles out of it .
View 10 Replies
I need walked through the take down to replace the head gasket on an 05 mountaineer with a 4.0. I've never worked on one of these so I don't even know. I havent even seen the engine to know where to start.
View 3 Replies
I just bought a used 5.4 for my 99' F150 4X4. My current engine has a blown head gasket. Anyway, I was able to hear the engine run before I bought it, and was able to check it out some. (oil, anti-freeze) I was told that this engine was bought from a salvage yard with 50K, and 50K more put on it before I bought it.
I was also told that the intake manifold is newer, from Autozone, and it has newer Accell coils. My question for you all, is ..... What do YOU think I should do otherwise before I install this engine. Oil pump? water pump? seals? ...
View 3 Replies
I have my 4.6L engine on a stand in the garage. I think I have a blown head gasket. I am ready to remove the heads.
My Haynes book says: "Caution:Use the required camshaft retaining fixtures to lock the camshafts and leave the tools in place."
A google search shows nothing. Why, what does it do?
View 3 Replies
