My wife was using my truck and she felt it lost power and ran rough, so she pulled over can contacted me. We both are deaf, but I can hear some and it sounds really bad. So, I had it towed home and I recorded it.
2001 F250 5.4 V8....
2001 V10- F250.. Runs rough- had the computer put on it and was coming up with P0174 codes (I think that is right)- In any case I replaced the Mass air flow sensor- checked for any vacuum leaks visually- I did not see anything obvious.... still runs like crap.... smells like gas when idling.... anything else I can check??? The check engine light went off finally (probably due to the MAF)- but it's driving me nuts- Any hoses I have not located I need to check?
View 10 RepliesLately my 2001 F250 5.4 engine is running rough when I am accelerating or keeping it certain speed. It feels like it is jerking. Like if the truck lost power for a second. This will go on for few minutes. Where to start to trouble shoot.
View 8 RepliesSo about a month or so ago i had my alternator replaced because my truck wouldnt start and had it checked and replaced well tonite it started rough dont know what to think what/where should i check first?
View 6 RepliesI have an 2003 F250 7.3 Diesel 4wd. Yesterday I knew I was low on fuel but I don't think I ran out of diesel. My gauge was above the "E". 50 miles left on my overhead readout, but you never know. All of a sudden the truck misfires and is running very rough before it dies on me. I get it towed home.
Thinking that it possible I ran out of fuel and screwed up my fuel pump, I bought a new fuel pump and fuel filter, installed them and I have the same symptoms. I am guessing I lost my prime, who knows. I have 180,000 miles on it and haven't ever had engine problems.
V-10 running rough at idle, chugging. a problem has developed with my 2004 E-350 V- 10 after having a new fuel filter installed and the induction service done . Picked it up from a local shop and it was running rough after bringing it in when running great! I figured maybe it fouled a plug or something so I drove it home but it didn't improve so I brought it back and had new plugs installed. It is still running rough and wanting to almost stall when accelerating from a stop and the shop cant figure it out , not showing any codes.
I'm thinking maybe they caused some type of vacuum leak that is so far undetected. The killer is it came to the shop running great !!
No other problems with the vehicle, I drive it every day and have owned since new. 278,000 on it now and it has been the best vehicle I have ever owned.
I bought it and changed the fuel filter and it was dirty. Then ran a tank of gas with seafoam and then with lucas fuel injector cleaner. Still nothing. It idles like its missing and as long as you are light on the pedal it revs up fine but if you're heavy on the throttle its. Its has no codes that's why I haven't replaced the coil packs and plugs but they have been ordered. I just thought there would be an engine code if any of the coils or plugs were bad. Looked for a vacuum leak but couldn't find any. The donut gasket on the pass side is bad would that cause it to run shifty with no code.
View 2 RepliesI have a 2000 Ford F-250 6.8 v10 that is running rough and cutting out when I give it gas but I can turn the key off and turn it back on and it will run right, what it could be?
View 1 Replies1999 F350 & lately if I don't plug it in even if it's like 40 out for like the first 30 sec sounds like its only running on 4 cylinders than it'll just even out & alls good. thinking glow plugs here. I did replace them last fall unfortunately with the cheep ones that I been now reading bad things about.
View 2 RepliesMy brother is having a issue with his 99 F350 diesel 7.3 automatic tranny pu. When in manual 1rst gear the engine stumbles and runs like crap. In drive or 2nd gear it runs fine. He's getting a code for a bad cam sensor. A new OEM and aftermarket sensor has been tried with no solution to the engine problem. What might be going on? Maybe a bad ECM.
View 2 Replies2008 F250 5.4L 150k. My truck has been driving pretty rough in low gears, rough idle, and today the check engine light came on then getting on the interstate the light started blinking. I ran the code it came back 0307,300,308,300. After doing some research on here, I've come to the conclusion to change out the coils on 7 & 8. Questions are, should I change plugs as well? And how important is it to keep all the boots (of all 8) the same color (brown or black)? And should I expect to change all the rest soon?
View 1 Replies2002 7.3 running rough.
This is my symptoms : On cold start ups engine runs rough. Idling it knocks worse than normal on the road she runs really rough. If I get on here she smooths out ( but still runs rough a bit) but normal driving at between 1200 -2000 rpm she runs so rough it shakes the whole truck. It will do this until she gets up to operating temp & then it goes away. The more she warms up the better she runs.
Once up to temp she will run perfectly. The colder it is outside the worse it is & the longer it takes for it to go away. I have replaced the valve cover gaskers and new harnesses, new glow plugs. Still same problems. I have AE and one time it gave me a #2 cylinder code. have not been able to repete this code. What to check next.
2002 F-250 SD V10 Auto Trans 140K miles.....
Engine ran fine until battery died. Vehicle then sat from Nov to May with no battery in it. On start up now after install of new battery, engine initially surged at idle and seemed to miss (run rough) in gear/under load. No CEL or codes. After a single short drive idle and running under load seemed to have improved a bit, but not yet back to what I would call normal.
QUESTIONS:
Is this simply a matter of the computer having to relearn after battery disconnect?
Will driving restore things back to where they were/should be?
How much driving/How far?
I have a 1999 F250 SD V10 4x4. I recently had a transmission installed and the truck is running erratic. I have an engine miss (sometimes when idling, more so when in drive and foot on the brake). I say sometimes because there are times it will not miss and the engine runs smooth. The transmission shifts a little strange and sometimes hard.
I am getting a code reading that says my TPS is faulty, but I installed a new one a few months back.
The engine is running rough (jerky on acceleration) especially when driving. I was wondering if I should take it to a shop and have them flash the computer to reset it?
I also remove the AC compressor a while back (bad clutch). I installed an aftermarket pulley.
I have an 02 f250 V10 with a rough idle (90K Miles). It's not horrible but it's obviously not running perfect. Everything seems ok when I am up and driving, especially at freeway speeds. I recently noticed that if the truck is in park and I run the RPM's to 1500 or 2K and quickly let off the gas it will die. It never throws any codes. So far I have replaced the IAC Valve, fuel filter, O2 Sensors, PCV valve, cleaned the MAF sensor and replaced the air filter. Plugs and boots were replaced 5K miles ago. Fuel trim levels on both banks are running around -3.1 to positive 3.5 based on what the computer is telling me. Also according to the computer the vacuum sits steady around 25 at idle (+ or - .2). I don't have a manual vacuum gauge, just relying on the computer. I've also gone around to every plug and disconnected both the injector wire and the COP wire and they all seem to equally affect the idle as well as the fuel trim levels.
View 11 RepliesI have an 02 f250 5.4. I just did the intake manifold. I also changed the spark plugs and the valve cover gasket. Following this I drained the oil and filled it with fresh oil.
It started right up but it felt like the engine was really vibrating and running rough. The check engine light than came on. I don't have one of those tools to diagnose it.
What could be wrong?
My truck has been doing this for a while now but it has progressively gotten worse from about three months ago when I went through some deep water. I don't believe it had to much to do with the water, I just think that the water is what didn't deal the situation and lead to the problem becoming more prevalent. But continuing, yesterday it got down into the high 20's and my engine started acting up (rumbling coughing, surging while at/leaving complete stops) and then it finally through a code for once and I head over to the neighborhood AutoZone expecting to get a lean code (because when the engine is acting up really badly I can unplug the fourth cylinder fuel injector without the engine acting any differently) but instead I received the p1152 (bank two lack of switching (rich)) code....
At this point I believe it is a faulty fuel pressure regulator, but without a good diagnostic obd2 reader or a fuel pressure gauge I'm not sure what to do. I'm currently in college, money is low, and I'm trying to take an accurate shot at the part that needs to be replaced so that I don't have to buy more than one part. Of course AutoZone says o2 sensor but I changed both about five months ago.. I've been chasing this diagnosis around for way too long now. (It's on a 2002 ford f250 5.4l super duty)
My '99 was running rough - coughing/spitting/sputtering when under a load - especially at lower idle/rpms and going up inclines.
Brought to mechanic and he put it on "the scope" which told him the #1 pack was bad. Replaced. Got it back and it ran better, but, then went back to the coughing/sputtering.
Replaced the spark plugs - OEM Motorcrafts. Seemed perfect for a wee bit, now I notice an occasional cough/spit but all in all not bad.
Curious: was it foolish to not replace ALL coil packs at time of plugs or is it ...acceptable to do just the plugs and then come back and do packs if needed.
So, I have a 2007 f250 with the 6.0. When she's cold she starts fine but runs rough like she has a miss. When she warms up the miss goes away and it runs pretty good. But if I shut it off it won't start for about an hour or so.
ICP sensor has been replaced.
FICM is putting out 50v
Ok just bought this truck ran fine. Put a sct tuner on that the truck came with and some how got the egr turned on. It had a egr delete so it was smoking and finally found it out that it had turned on but fixed it. Now we have another problem, it will start up and run fine and about 45 seconds it will start running rough and go into a limp mode. It will run rough and starts to die slowly and when it starts to die there is no throttle at all.
View 4 RepliesCEL came on last night, OBD code PO420, truck is an 06 f250,5.4? Btw, truck running rough, no power on acceleration, in gear at idle, runs rough....
View 4 Replies