Got a 2001 F350 diesel auto, 295k miles.
It has miss when over 2000rpm. Below 2000 its smooth.
ICP has oil in sensor, ordered new one. Gonna change oil too.
CPS is new (not sure if its black or the other one). Starts idles and drives good otherwise.
Where should I look?
I have a 2000 F350 cab and chassis 4X4 with V10 and a 5 speed manual (actually it's a 4 speed with overdrive). My problem is the engine seems to have a miss in it. When I first start it in the morning it usually runs good for 5+ miles till it warms up then if I am not pulling a load I can hear what sounds like a miss but the truck accelerates fine. If I am pulling a load I can also feel a slight steady consistent shudder and I can tell the truck doesn't have the power it should and the gas mileage SUCKS worse than it use to.
I ran a bottle of Lucas deep clean through a tank of fuel and that seemed to work a little but I will still encounter the problem sometime during the day. When the miss seems to be gone I can hear a very slight pinging noise when I accelerate or pull a hill with and/or with out a load. The pinging noise I hear sounds like an engine with a distributor that is getting to much spark advance if you have ever experienced that before.
I purchased this truck used several years ago and I don't know what the PO did but the check engine light is not coming on and it doesn't throw a code. I put 10 new ford coil packs on it about a year ago so I really don't think it's a coil pack, but I could be wrong. To me it sounds like maybe it an injector problem????? I know there are several sensors on this engine and I am thinking maybe a crank position sensor is not working right but I honestly don't know???? Is there a way to test this sensor?
I have a 2000 F-250 V10 that misses (cylinder 10) at the idle, once you give it gas it runs correctly again. I am at a loss. I have replaced the plug, tried moving coils from one cylinder to another to see if it shifts the miss, and it has new injectors. What this could be?
View 9 RepliesQuestion, my truck started to have a miss under normal acceleration, when I really get on it, it clears up? I also noticed a bad sulfer smell at idle. Im thinking the cat is possibly plugged? Truck had 172000ish on it, and the cat is original. I did do a big tune up this past fall, new plugs, coil packs, air and fuel filter. Should I put a new cat on it? And a new oxygen sensor?
View 9 RepliesOn a 2000 F-350 with 5.4 engine, where does the vacuum line enter the cab? I got a truck in with no vacuum signal to the heat controls, and it has a slight miss at idle. Both of these are signs of a vacuum leak, but i can not find the line going into the cab.
View 5 RepliesMy 5.4 had a bad miss several months back with no cel. It would barely climb hills it never even needed extra throttle on before (3rd gear, wide open, 35 mph, etc). Ford dealer ran a scan and it had two bad coils and plugs. I changed those and it ran much better, but still had a "pfft pfft" exhaust leak type sound at idle. I checked the exhaust studs and they were all good, so I wrote it off as just a normal exhaust leak.
Full throttle in 5th gear to maintain speed limit when normal throttle before was sufficient. I got home and parked it and it sat over night. I went to start it today and it died. Tried again, died again. It only stays running if I am pressing the gas and I hear a fluttering or air sound of some kind coming from the passenger's side of the engine. It doesn't cut out or miss like a bad coil or plugs, but like you choked off the air supply.
All plugs are still in place, exhaust studs look good, tried it with the air box unhooked to see if it got clogged, and going to check intake leak tomorrow...
Having problems with 1999 or later 7.3 missing or dying when you turn on the wiper switch?
View 8 Replies2010 f250 cc 5.4 145000 miles. I bought it last fall have not drove it a lot. When using the cruise control and a load is added grade or hill in the roadway. It jerks hesitates or miss then cleans up and runs fine. When using the accelerator it does not do this. No codes.... Thinking about changing the plugs.
View 5 RepliesI know this is a common code and a common problem. I have had a buzz test and glow plug test done, no codes. Scanner code came up with P0275. I have read about injector change out, to O ring failure, to new EGR style. I have a 05, 6.0 SD SRW auto.
View 1 RepliesI have a E350 5.4 with 200,000 miles and it ran great before winter, this spring I fire it up and it got a miss I drive it anyway it starts to clear up and now the 1289 code. Everything looks fine coolant engine temp. I wonder if you can bypass the Cylinder Head Temp sensor. I am thinking the engine management is causing the miss to cool the engine.
View 3 RepliesI just purchased a 2003 F250 Super Duty with the 6.8L V10 It has really high miles on it as it was a landscaping companies fleet truck. I'm sure that it was pretty well serviced as it has 300K miles on it and it's still running pretty decent.
I picked up the truck and I have to get the smog done soon. It idles with what I can only describe as a slight miss and it runs and drives great. seems to have plenty of power for the miles that's on it.
There is no active CEL on but I scanned the OBDII system and found a P0171 Lean bank 1 code in the pending codes list of the scanner. I guess this year engine doesn't have an EGR Valve or DPFE sensor because I've looked high and low for it and there non existent on this engine.
I've checked for vacuum leaks by spraying brake cleaner or carb cleaner all over the place and it makes no difference and all the vacuum lines and connections look okay.
When it's running It does sound like a vacuum leak right behind the top of the plastic throttle body but I can't find it, I don't know if this big *** engine just sucks that much air or what.
Like I said I need to smog this thing soon and I don't want it to fail if it's missing or has another issue. The fuel injectors look new and one coil pack looks like it's a replacement...
I have a 2003 f250 5.4 with a couple of bad valves and low compression and a dead miss because of it... I just bought what appears to be a 2001 5.4 from an f150... I am worried now this engine wont work and cannot find anything online that can tell me yes or no....
View 12 RepliesHave an intermittent miss I can feel when driving 2006 F250 5.4 l 4x4 stick; Freeze frame from Cen-Tech 60794 (from Harbor Freight) scanner follows.
DTC CNT 0
DTC FRZF P 0352
FUEL SYS1 OL - FAULT?
FUEL SYS2 --
LOAD PCT 25.9
ELT (DEGREES F) 186
SHRTFT 1 0.0
[Code] ....
I can operate the scanner but what these ranges should be. What might be causing the miss? This scan shows 951 rpm, I was idling along in 1st in traffic, but I have also felt the miss at 75-80 mph (about 2300 rpm) on the Interstate and at other times, with light loads in the 1500- 2000 range in town.
This last April I was towing my trailer back from camping approx 125 miles when I detected a loss of power and a slight miss. I managed to make it home. It wasn't until I made it home that the engine finally started coding. Miss on start, a couple of cylinders missing and output shaft speed sensor circuit failure. So naturally, I decided to do what I felt needed done anyways, change all coils and plugs. Oddly the problem got worse to the point where I almost didn't make it home after test driving it, it kept stalling out and was difficult to keep running.
After some research and advice from others, I started replacing some components; MAF sensor,IAC valve, output shaft speed sensor. Nothing. In fact now the truck wont move, I start it up it idles a little rough, but then I put it into gear and with in seconds she shuts her self down. I've replaced the fuel filter, checked the fuel pressure and it is in specs. I've now had it towed to two mechanics neither of which have any solution. They've put expensive computers up to it and still nothing. I really do not know what to do at this point. Lastly the only code that continues to come up is P0720, output shaft speed sensor circuit failure, I really miss my truck!
I got an f-350 drw it is sluggish on take off feels like a miss. Higher speeds when you step on it. It seems o.k I have been told it could be a crank shaft positioning sensor any in put on this. I have changed the fuel filters, cleaned the e.g.r. valve and yes it was pretty clogged,air filter seems to be good. And 1 last thing for now where would c.s.p.s. be located...
View 4 RepliesI know that this horse has been beaten to death but after searching all the posts and web. I have recently aquired an overhead console and wiring harness from a 2000 F250 and want to install it in my 2001 F250 which did not come with one. The connector behind the passenger kickplate is different so I assume I'll be doing some wire splicing. After reading all the previous posts, I'm unable to find old bird. Apparently he's not around anymore. Looking for the template/wiring instructions for this retrofit?
View 3 Repliesi'm looking to upgrade my mirrors. A friend told me to get the 08+ mirrors but I can't find anywhere online that says they will work. I'm hopefully going to be purchasing on Amazon but not sure which ones to get. When I pull up the 08+ they say "Fits Ford 2008-2015 2008 2009 2010 2011 2012 2013 2014 2015 F250 F350 F450 F550 Super Duty"
Ive got the 2000 F250 V10
I have a 00 F250 7.3 4x4 and I am looking to get better mileage out of it since it is now a dedicated work truck for towing. The two options I have in mind I think will work, but just wanted some clarification and if one is even possible.
First I will be taking the lift off and dropping back down to 33 inch tires or so. This should give me a little, but if not it should be easier on the truck for towing.
And this truck mostly see's highway miles, so I was thinking about disengaging the 4wd. I heard 4wd trucks get worse mileage, so this is the one I didn't even know if it was possible. not digging in to the computer and injectors quite yet.
Have a 2000 F-250 V-10 4x4 with 335,000 miles on the clock. Has started hesitating at 40-45. You can't really notice it at idle. Drove it around at lower speeds and just a miss here and there. Take it up to 40-45 and it's quite bad. Hasn't thrown any codes. Hooked it up to the scanner to get no additional info. My gut says coil packs but am kinda confused that I haven't gotten a misfire code yet. What to check?
View 6 RepliesA vibration has just begun on my 00 f250 power stroke it's in the left front and happens when I hit a bump I changed out the wheel bearing assembly and I switched locking hubs with another truck all with no success don't know what else it could be it does go away if I lock in the hubs so idk
View 2 RepliesI have a 2000 I got new in sept of 99 its a good truck and id like to keep it as long as I can its got 173,000 on it I take care of it garaged kept and consistent fluid/filter changes all over top and bottom few minor addons like turbo bak exhaust from Silverline,auto meter gauges so I can monitor temps ,a bigger transmission pan aluminum I did years ago ,a gear vendor 8 speed addon years ago,diablo predator tuner with the 80 horse tune been doing great for a quite a while lately I noticed if I leave it idling in park for a few minutes while in a store r sumpn it won't shift outa 3rd its like overdrive is turned off I have to pull over and kill&restart 7.3 and take off its fine what in the wide wide world a sports is happening my overdrive switch has been out for a couple years I just haven't replaced it yet it gradually got worse when using it id have to pull shift lever in to get it to engage then put in neutral then in park now cant get it to work at all hopefully I can fix it myself but my luck is never that good.
View 5 Replies