I have a 2001 F 350 with a V10 it keeps coming back as a misfire on cylinder 3 and 4.. I replaced all of the coils and plugs and pigtails I have even swapped out the coil packs from side to side and I still keep coming back with the same code. The truck has a bad check around 1500 RPM with a load on the motor mainly doesn't in overdrive and first starting off...
View 14 RepliesMy dads truck started misfiring last week, first thing i did was scan the codes and got p0303, p0304, p0305, p0306, and p0308. Its an 08 F-350 5.4...already changed out the spark plugs and the same codes came back. I decided to do some further testing and so far all coils had spark as well as 12.4 volts going to each. I did check the switching signal and that was present as well.
Moved on to the injectors and i checked each connector with my noid lights and it flashed on all cylinders. Did a resistance check on each injector and they all registered 12.4 ohms. We did switch some coils around and all the same cylinders misfire. My next step is to do a compression test.
My biggest question is if there are any common problems with these engines besides the coils, by the way this truck has the brown coil boots and the spark plugs that dont break in the engine.
I have a 2002 F250 5.4 L with an intermittent Misfire. A little history on the truck in 2011 I replaced the motor with a Ford long block motor, only the block, I used my electronics, intake, etc, this was brand new from Ford. The truck has a total of over 300K miles. Recently it has developed an intermittent misfire. I have changed all the coils and plugs and the misfire is still present. The codes are showing a misfire in cylinder 3 but could be 4 too. The misfire is intermittent because this morning I changed the plugs and truck ran fine, drove to store and it started missing, turned truck off and started up and ran fine again. It has been doing this off and on for a few weeks.
View 10 Repliesmy 03 f250 has a 5.4 and i cant seem to get rid of a misfire in cylinder 3. i had a p0353 code but that no longer shows up. i replaced all the coils with Accel coils, replaced the plugs with motorcraft platinum. i have checked the wire all the way back to the PCM and it checks out. i replaced the pcm with one that has been reprogrammed. i have swapped the injector and coil with another position and still get misfire at #3. Replaced the coil connector with a new one. I have good fuel pressure. I no longer get the code but the misfire is still there, unplug the coil and injector while running and no change. Unplug a different cylinder and you can tell the change. I checked compression and its good. I am lost here!!!!
View 14 RepliesI bought this 2004 V10 Ford truck new.. It was at that time top of the line Ranch King with all the bells and whistles.. I have been trying for some time to figure out the miss I have. I was told yesterday that.. Misfire 2nd cylinder passenger side no compression.. They said I need to have a new Engine installed.. They would look for a rebuilt and would cost with installation around 5 grand.. I then took it to another garage and was told that's not it, but will check it out later in the week.. What I should look for.. No one seems to b able to figure it out.. I cannot afford a new truck at this time and 5 grand for this one to fix is not a reality..
View 8 RepliesMy 5.4 F250 with 200,000 miles having many problems... It all started a few months ago, when the cam needed to be replaced, and a cam phaser was also replaced at the same time. It ran fine after, then threw a code for cylinder 3 misfire. The guy I took it to said it was due to the huge crack in the exhaust manifold and that was messing with the o2 sensor coming up as a cylinder 3 misfire. So, got the new manifold and it was good for a few weeks.
Now, starting the other night, Friday the 13th, it threw a CEL when I was coming into the driveway. It had been throwing a code every once in a while, and I brought it to school to scan it Friday the 13th but there was no code. So, I assume that it is an intermittent problem, no big deal. When I go to get in my truck to go to work a few hours later, the 5.4 cranks... and cranks... and cranks.
I get it to fire up, and it dies again. Run codes, and it says that the cam positioning sensor is broken. Replace both of them, still acts up ie. doesn't start when it does start it runs very rough and stalls. Get it up to my uncles shop, and replace fuel filter.. Still runs like trash. Run codes now, and it says rich/lean in bank 1.. My uncle tells me to move my truck out of the shop, so I start it up, and it runs great. No hiccups, it idles perfect as I move his truck out of the shop first.
I park my truck outside and let it idle for about 10 mins, and when I come back out it is still idling, perfectly fine. I get in, put it in reverse, and get about 20 feet when it dies and will no longer start back up. What could be going wrong?! Sick of throwing money into this thing! At one time while started up in my uncles shop, it was blowing black smoke, as if it was a diesel!
I have a 99 ford super duty with a 5.4 triton that is having a troublesome misfire. When you first fire it up it has a bit of a stutter then runs relatively smooth but the engine does still have a small shake to it and you can hear a bit of a choppy sound in the exhaust. Not completely smooth. When you drive it light footed it seems to run perfectly smooth and nice. But if you go past half throttle (sometimes you can go past that point) it starts to cough and is very slow at picking up.
When you reach between 3,250 and 4,500rpm the coughing stops. But the pick up is a little surgy, not steady. It was doing this for a while before the engine light came on. I got it scanned and it showed a miss fire on cylinder two so I have replaced the spark plug, coil, and injector but still the same issue. I opened up the catalytic converter to see if it was plugged up. Nothing there.
Truck Specs:
2008 f250 super duty 5.4l
78xxx miles
4x4
Automatic
Issue:
P0300 (random misfire detected)
P0307 (cylinder 7 misfire)
Let's start from the beginning...
I was getting the notorious 5.4l ticking sound. After doing research on this issue. I found that it could be a few different issues including:
Cam Phasers
VCT solenoid(s)
Loud injectors
Valves
Exhaust leak
Loose spark plug
The list could possibly go on, but these being top concerns or issues to look into.
I took it to my mechanic and wanted him to research the ticking problem. This was my primary concern due to it was getting worse over time. I didn't want to do more damage than what was possibly already done. I told him to go ahead and change the spark plugs while you're checking into what's going on. (I know those plugs can break and I didn't want to do that.)
At any rate... the plugs got changed to motocraft brand (I know the trucks can be finicky with the parts you put back into them so I went with the motocrafts to avoid any complications.) After the plugs were changed, he told me that the ticking was caused from a blown exhaust manifold gasket (yay me... not internal parts or anything too serious. Sweet!)
I had to reschedule to get the gasket done, but knowing what it was now I wasn't too concerned about driving it. So I did. The new plugs are also in the truck at this time. I drove it the next day and right away.. I noticed a misfire. Thought maybe the plug was bad. I told my mechanic about it and he said... Sounds like a COP to me.
So I get a new COP. Okay.. easy fix. Installed it and still got a misfire. Told my mechanic and he said get another COP. So I'm thinking.. "Okay.. get a new part to fix a new part.. sounds logical.. lol" so I do what he thinks might be best. I replace the COP with another new one and it's still misfiring. The new cops are also motocraft brand as well.
Okay... next step.. he claims it may be a VCT solenoid issue. At this point I don't care.. I just want my truck fixed. So he replaces the driver side solenoid. Still misfiring..
So after doing some research on the scanner... we locate some issues that are the exact symptoms I'm having. Misfire.. at low rpm.. during cruise control.. and a sudden at idle.
This information states for this drivability issue.. to spray injector cleaner/carb cleaner into the engine and possibly clean it out. Makes sense. He did this as well as changed the fuel filter. Also did a pressure test on the injectors to make sure they were good. They were. After spraying and cleaning it out, it was taken for a test drive and it seemed okay... but not perfect. The next day.. the misfire came back.
He said that if the misfire returns, that I need to contact the dealership and see if there is a pcm update. The dealership said there probably is but can't tell me until the computer is hooked up to it. (Of course there is a charge when it's hooked up) again.. whatever.. I just want it fixed. The truck is scheduled to go in next Wednesday for that. If that doesn't fix it, my mechanic said cam phasers possibly bUT still not sure for sure..
My dad gave his 2005 Ford F-350 truck with the gas 5.4L (?) I drove it home. If i floor it it misfires badly, or if the RPM's get over 3000 it misfires then about 3800 it stops and keeps going. but i can't give it to much gas....
The spark plugs where replaced 2 years ago along with the cat converters. I can hear some very fait manifold gasket leak ...
A few days ago it was raining and it had a bad misfire with blinking CEL. but it never threw a solid CLE. can i still put the codes on it to see what cylinder it is? Are these issue related? Where should i start?
I have a 2000 f350 5.4 liter I recently fixed a misfire in cylinder 1 since then every morning the truck runs perfectly fine however at night when I leave work around 6 o'clock the truck has a misfire again I stopped pullover pull the spark plug out put the spark plug back in and it runs perfectly fine all over again I don't know if this matters but when I replace the spark plug I only replaced one and not all 8 same thing with the new coil pack I don't see how that could cause this.
View 14 Replies1995 7.3L f350 400k mi developed 1poss 2 cyl miss does not change after warm up and will die after 10 min .
View 1 RepliesAfter replacing most of the underside of my Super Duty, Complete front end, backing plates, brakes, rotors and shocks, I have a misfire code on cylinder #4. I replaced the plugs, cleaned the MAS and filter and rotated the coil to cylinder #1. Still have a misfire on #4 and noticed the coolant slightly low and some condensation on the oil cap. Could this be the intake gasket? My mechanic is away for 2 weeks and I think the price at the dealer will kill me. I have 63K on the truck, don't tow and plow mostly family members. It's getting a little rusty but is still in good shape.
View 13 RepliesI had a 05 f350 5.4 3v come into my shop with a CEL. Did the usual it had a p0307. So I did the usual again changed plug and coil plug cam out no prob they were done 15k ago. Test drove a few times and it was fine. Few days later customer brought back with same code p0307. thought maybe I got a bad plug or coil so I moved them to #6, misfire stays on #7. When I drive it local its fine when I go to pull on to highway and really put my foot in it CEL flashes (misfire) and it pings like crazy and loses all power. Scan it back at shop and still only p0307!!
View 10 RepliesI have an 04 F350 with Glow Plug errors on cylinder 2, 4 and 8. I have already replaced the harness on that side because the old one was gunked up pretty bad. Still have the same issue. Does this sound like a GPCM issue to ya'll?
AE pulled the following codes:
P0672 Cylinder 2 Glow Plug Circuit
P0674 Cylinder 4 Glow Plug Circuit
P0678 Cylinder 8 Glow Plug Circuit
Not having issues starting but it rarely gets into the 30's here in FL.
I have been having some inconsistency with my transmission in my 2005 F350. I bought it used 2 months ago and have had the low/tow overdrive light blinking. a month ago I removed the pan and changed the filter in the transmission. I had a friend run the diagnostic test and found transmission solenoid code as well as both cat. converters as well as my Number 8 cylinder misfiring... I pulled the transmission pan and filter to find what appears to be 7 solenoids? Where to start?
View 1 RepliesI went out getting firewood in my 2001 F350 4X4 6.8l V10 auto . Backed up to the slash pile, put the truck in 4X4 Low and went to work.
When we finished I flipped the switch to 2WD, but the transfer case would not dis-engage and the IDIOT LIGHT on the dashboard stays on 4X4 Low... I can't get the truck out of 4X4 Low. I turned the hubs from auto to lockand its still stuck in low range.
How to diagnose misfire with no CEL? 2001 F250 5.4. What could cause it?
View 13 Replies2001 f350 w/v10, 6.8. the fender mounted starter solenoid went out so I replaced it, while doing so I also replaced the battery (previous owner had a marine/rv battery installed, I purchased the truck a couple months ago). after replacement the truck still will not start. when attempting to start it barely if at all cranks, long story short I was going to have the starter tested but in the course of removing it the terminal posts broke off so I ended up replacing it too. The truck still would not start or really crank so I dug down with the expectation of finding a bad ground someplace. cleaned up the ground points. Now I have the battery on a charger awaiting it to finish recharging. Something that is likely/remotely likely to be causing the engine not to crank over and start that I have missed?
View 11 RepliesMy abs light is on. The guy I bought it from said he thought it was the sensor but who knows. Is there a way to test the sensors to see if they are working? Also can any other possible issues to look for? 2001 f350 7.3 xlt...
View 3 Replies2001 f250 v10 6.8l runs a little rough at idle, low rpm is ok between 1700 and 3000 rpm but around 3 it starts to shudder while driving let off gas get back on its fine, new plugs 1,000 miles ago has throttle body spacer and cold air intake, stock everything else..
View 8 RepliesBought truck drove it 240 miles on interstate 80 mph no problems---2001 F350 4x4 auto. Next morning backed out drive and trans fluid trail 6 inches wide. Didn't leak in forward gears (at that time) added fluid and drive to town shifted fine.
Next day gonna drive 150 miles to check out leak. (Son was driving it) said it wouldn't go over 40 mph. Revving high. Hauled truck here on trailer and pulled tranny. Rear housing cracked just before 4x4 adapter. (This trans was rebuilt 10k miles ago) ..
Got used 4R100 from friend who replaced only because he built one for his truck. It was shifting fine etc when pulled 6 months ago. Used cracked trans TC and installed. Test drive no 4th or OD. Pulled trans put TC that came with trans in. Still no OD. Put on scanner while driving. Trans is being commanded to shift to OD but not up shifting. 45mph at 2400rpm.
Pulled plug to solenoid pack inside trans ( this should make trans default to OD / limp mode) still no OD and won't go over 45.
Pulled OD button checked wires inside steering column. All looks great. Not even a heavy rub mark.
Should I replace the coil pack in trans? Where do I go from here? Again this trans was known to be good when pulled 6 months ago.