Ford Super Duty (1999-2016) :: 2001 F250 - Cruise Not Working
Jan 8, 2016
I have a 2001 F250 with 7.3.... We swapped the auto for a zf6 manual.... We left the auto's shift position sensor tied to the frame and left in neutral. I did install a pcm from a manual transmission pickup. Also have the clutch position switch hooked up. I have an Edge Evolution CTS2 reprogrammer, and on the display the gear indication always shows P. I suspect that is why my cruise doesn't work. For interests sake, I tried manually adjusting the shift position sensor through all gears, and the reverse lights come on when in reverse but the Edge's display always shows P. My question is with a manual transmission, how does the pcm know that it is in gear? The only sensor that I am aware of is the reverse sensor on the zf6.
View 2 Replies
Advertisement
I've just bought 2001 f-250 crew cab and when I push the cruise control on the steering wheel it does nothing. Maybe a fuse or does my year have one of those master cylinder switches?
View 12 Replies
1999 F250.. What would cause my cruise control to work sometimes and not others. it may work today and not tomorrow.
View 2 Replies
2000 F250 Super Duty cruise control not working. I looked through a lot of threads on this subject and cannot pin point my problem. Cruise control was working, had to slow down wile approaching a town, back on the highway and now it won't turn on.
Looked at the brake pressure switch, it was till good but was the old type but had the recall harness on it. Bought a new one and replaced it anyways. Still nothing. All my brake lights work, I also did the Cruise control diagnostic and it passes everything. No lights on my dash are on, speedometer works, horn works.
The only thing I did not check is the Vehicle speed sensor. Even though my speedometer works and my ABS light is not on, can this still be the problem? If so how do you test it? Do I just remove it and test continuity?
View 10 Replies
Cruise won't power up. Tried entering diagnostics but did not get any flashes. By-passed switch on master cylinder, did not make any difference. Horn honks. Brake lights work correctly.
View 9 Replies
I have a 2003 F250 Super Duty 5.4 crew cab. Cruise light comes on when engaged but does not work. I did some research on why its not working checked wiring at the throttle body it seemed ok, Fuse is ok. Also did the self test and everything passed with just one flash but cruise still does not work. I read about many problems with the brake pressure switch but would it pass the self test if that pressure switch was bad? Also what should a switch cost. Local dealer wanted $125.00 for a new one and I have read where they cost around $15.00 - $20.00.
View 12 Replies
2001 F250 SD 7.3 PSD Was doing a trailer towing road trip too and from Montana. On the way back the cruise control stopped working. Checked fuse #28. Looked fine. Attempted to do a self test on the cruise control. Holding the OFF button did nothing. Never went into diagnostic mode. Button ? A different fuse?
View 14 Replies
Just got a 2001 F-250 Super Duty (crew cab, long bed, 4x4, 7.3L turbo diesel) and have been going through and fixing a lot of little issues. The one that now has me stumped is the interior lighting circuit (which is also the bed light). Here's what I've got so far:
Map/reading lights work, but dome lights do not (neither automatically nor when turning them on via the dimmer switch). Verified all fuses in the PDC as well as the interior fuse panel (behind the driver side knee panel). The interior lighting relay was missing, so I purchased and installed it.
Relay #1 (interior lighting), fuse #4, and fuse #14 are all good - when I pull the fuse with the door open, the relay clicks (and clicks again upon reinstalling the fuse). With the doors closed, the relay clicks when activating the interior lights via the dimmer switch.
The LT GRN/YEL wire is hot, and all related accessories work (map lights, engine bay light, etc).
The BLK/LT BLU wire is not receiving power from the relay from what I can tell.
Before I start trying to pull out the fuse panel to start checking connectivity, anything else to check? The ground at the rear driver corner of the cab is good, and a visual check of the harness running down the driver side of the cab has no visible signs of damage.
Also, given that the relay is audibly actuating the way it should, I'm guessing that the GEM can be ruled out as a possible cause? My next step will be to get a pinout diagram for the relay and crimp a quick jumper to see whether or not it's simply a defective relay... But I doubt it's the case.
View 6 Replies
Funny thing - had the truck in the body shop for several weeks and when it went in, everything worked. Got it back, and some of the radio buttons don't work. These are rocker style buttons, and when I push the AM (left side) that works. Press FM, and it won't go to FM. Press the right side of the tuning button, and it won't go up the dial. Press the left side, and it will go down. Same for cd. Left side of button goes backward through the tracks, but right side won't advance. Bass/treble button: Press bass (left side) and that works. Press treble (right side), and nothing.
View 2 Replies
2001 F-250 7.3. The auto lock hubs are not working on the truck lock hubs in and all works fine. First thought is the vacuum system has a leak or something of the sort. Had truck at the shop they are telling me the GEM module controls the vacuum to engage the auto hubs and the signal is not coming from the GEM and it need to be replaced. It was the GEM causing the problem.
View 6 Replies
I have an 2001 F250 SD with 7.3 Diesel. Headlight switch failed and I replaced it. But now I have no high beams and my dash lights that light the dash up don't work. Gauges, fog light, low beams all work fine. Fuses checked. Multi function switch checked. What to do next?
View 1 Replies
My drivers window will not work at all but when I push the button I get a clicking in the fuse box. The other 3 windows partially work but will only go up or down in small increments. I have tried holding the button and slamming the door and this allows the other 3 windows to work. I thought it was the switch so I replaced it and that was not the problem. Fuse and relay seem to be fine. If it was just the driver window I would think it was the lift motor but with the other 3 windows on the fritz I have no clue.
View 1 Replies
I have a 2001 F250, 5.4, 4X4. My ignition key stuck in the start position and when I pulled it back to the run position, everything seemed ok. As I started down the road, my speedometer stopped working and my overdrive light was flashing. Also my turn signals had stopped working and my A/C clutch didn't engage. Figured I burnt a fuse. I looked in both the under dash and power distribution box and all seemed well. I checked the fuse for the turn signals/flasher and it was fine. The flashers worked. Thought I might have fried something so I replaced the ignition lock and switch. Also my service engine light came on throwing a code for the vehicle speed sensor.
Looking for solutions on this forum and the internet, I learned that the turn signal switch could have gone bad and the VSS sensor is on the top of the rear dif and an easy fix. Well replaced the sensor but nothing changed. So I went back to the fuse box. Examined every fuse, big and small and I found a 10a with a small space. This was #24 under the dash. From the manual, "#24, 10A, A/C clutch, Blend Door Actuator, Trailer Tow Battery Charge Relay Coil, Four Wheel Anti-Lock Brake System (4WABS), Turn Signal." Replaced it and everything went back to normal. Turn signals work, A/C clutch works, no flashing overdrive light and speedometer works. All from a 10A fuse. If you have any of these symptoms examine all the fuses carefully. There's a 20A fuse for turn/hazard lamps and this other one buried that's only 10A.
View 1 Replies
I have a 2003 f-250 5.4l and the cruise control quit. If you press the on and coast it will honk the horn so I am thinking switches on the steering wheel or the clockspring. I need to test those. Everything else works fine....
View 6 Replies
Just bought a 2003 5.4 6 speed 4x4 F250 .. The cruise control does not work at all. The only fuse I can find in the owners manual is a 2 amp one .. it is in good shape .. Where do I look now to solve the problem??
View 8 Replies
The latest addition to the driveway (2012 F250 XL 6.2) is getting ready to be geared up for it's tour of duty. The one thing that was on the would-be-nice but not must-have list was cruise control. This truck doesn't have it, which wasn't a deal breaker because the truck was way inside my budget.
So anyways, while researching hitches, tonneau covers, steps, etc. I came across this : [URL] ....
Is this all I need to install the speed control? I would assume the dealer would have to get into the logic and enable something, but is this switch really all the hardware I need to buy?
View 4 Replies
Just bought the 03 listed in my signature line, and I just found out that the cruise control isn't working, so started trying to troubleshoot anything obvious.
When I switch it on, I get no cluster light that the manual shows to be to the right of the brake light. When I turn the key to run, it never lights up, so am guessing the bulb is bad.
Can't see how a bad bulb would keep the system from activating, so am thinking I have bigger issues. I pulled the fuse panel, but the manual does not have a listing for speed control. Which fuse it is combined into?
Also need the skinny on how to change the bulb. Can I reach my hand behind there? does the cluster have to come out?
Last question. What is the most likely culprit for non functioning cruise? A module? Perhaps the switch in the steering wheel?
View 14 Replies
Our cruise isn't working, I've read through the posts here and tried a few things
2000 F-250 V-10
-First symptom was the cruise light would light with the ON button and go off with the OFF button but I could not set the speed with the SET button. Now the cruise light hardly comes on at all any more.
- I've run the cruise self-test diagnostics and all the switch presses passed with no additional light blinks. After the static test the speed control servo makes a sound but does not move the throttle at all.
-The horn works
-Fuses are good
-Truck was taken to the dealer several years back for the cruise update. The pigtail with the green label is installed at the master cylinder. I've disconnected both connections and sprayed with contact cleaner.
That's about it. What it could be or what to test next?
View 10 Replies
I have a 2001 F-250 SD XLT with the ABS light on, cruise control doesnt work and the horn only works with the key out. The codes for the ABS is no signal input from the left and right front wheel sensors. No problem there. Also my speedo stops or jumps when I press the horn button while driving down the road. When I quit pressing the horn button the speedo works fine. So after looking over the posts on cruise control, etc. Does the rear speed sensor have anything to do with the cruise, horn not working? All fuses are good so I am thinking the cruise control switch on the master cylinder or a short in the steering wheel column or my ignition switch. What do you all think?
View 7 Replies
For about 6 months the cruise control on our '09 F-250 has been intermittently failing. One time I'll set it and it will work fine, the next time I try to set it and it fails. No particular rhyme or reason to when it fails to set.
Some of the tests that I did indicated it was the brake light switch on the brake pedal arm. It seemed to work perfectly a few times that I drove it after the installation but now it's back to working when it wants to.
I had a problem with the cruise on our '06 Ranger and it turned out to be the module. It acted a bit the same way in that it would set sometimes, other time not. I don't know if the two systems are similar or not.
View 6 Replies
Truck is an 02 F250 Automatic 4X4, 7.3 PSD.
Cruise control will turn on, will sometimes set speed and sometimes will not. If it does set and work it may kick off at any second or it may run fine. I have noticed it seems to kick off mainly after going over a slight bump in the highway or it may just kick off for the hell of it. Truck has 50,000 miles on it, I bought it new. Also having trouble with the throttle position sensor, it seems to have a "dead spot" at about 58 mph that shows up when I romp down on the pedal to pass on 2 lane roads. Can these two symptoms be related? Both are very aggravating. FWIW it does have the power adjust pedals. Truck is 100% stock, no power chips or other upgrades.
View 7 Replies
