Ford Super Duty (1999-2016) :: 2001 F250 V10 Won't Start - Solenoid Located?
Feb 16, 2016
My 2001 F250 will not start (clicks). I verified its not the battery and even tried to jump start it. I have never replaced a starter- but before I do that I read where there is another solenoid under the hood somewhere. I always thought there was just the one on the starter itself.
Two questions:
1. where is that other solenoid located and should I replace that first?
2. How difficult is it to replace the starter? I am pretty handy.
The issue is that I cannot get it towed easily - I just need to get it started at least once since my plow is still installed and it's hooked up to a trailer..
View 1 Replies
Advertisement
99 F250 Super Duty 5.4 has a p7147 error. Traced all wiring cant find any short. Bought reman solenoid pack # are f81p-7g391-cb with green cover my old one in trans is f81p-7g391-ba with blue cover. Are these interchangeable? Have tried to read up on pwm & nonpwm and getting confused.
View 2 Replies
I have a 2010 f 250 super-duty and i cannot get vacuum past the solenoid mounted on top of the radiator. Ford has given me nothing but bad advice. I know i have a vacuum leak after the solenoid and need to replace the lines going to the two hubs but when i switch on the 4wd and hook up a vacuum gauge the vacuum is good up to the solenoid about 12 inches. i constantly have 12 volts going to the center lead but nothing else in the other two leads either in 4 high, 4 low, or 2wd. Am I missing something here? shouldn't there be a voltage change when i turn the switch to 4wd to actuate the vacuum solenoid to let the vacuum pass thru the solenoid? I have tried replacing the solenoid but that did not work. Also use rubber vacuum line and make at down to the hubs?
View 4 Replies
I have a 2006 F250 Super Duty w/ turbo Diesel. Took to dealership for "hopping" feeling when turning sharp. Was told that 4 wheel drive solenoid was bad. Where this solenoid is located? I know I can fix but want to know where it is located.
View 6 Replies
I recently purchased this truck so I don't have any history on it. It's the V10 motor, automatic, 4 wheel drive, with a crew cab. I took it to Advance Auto to have them read codes and it came back with torque converter solenoid fault and 2 other codes related to that part. I didn't get to see the actual code numbers.
I've talked to 2 transmission shops and they said they could throw a solenoid pack into it, but that it might not even fix it. The truck drives fine, shifts fine, the tranny oil looks and smells fine, so I'm tempted to not worry about it until something else happens.
The truck has 217,000 miles on it...
View 10 Replies
I have a 4r100 in my 2000 f250 7.3. I am getting a P1746-EPC Solenoid, open circuit. Does this mean this particular solenoid in the solenoid body has failed and should i replace the solenoid body?
View 3 Replies
My '01 f250 7.3 has gotten hard to start. It seems to maybe be due to cooler weather, but not always. I have been told that there is some sort of valve in the fuel tank that could possibly cause this when the fuel gets around a 1/4 tank or so. But, it's doing it at any fuel level. But it doesn't do it all the time. I do notice it more in cooler weather. Anyway, when I try to crank it, I'll let the "wait to start" light go off and then wait a bit more. I'll turn it over and it almost as if the batteries are weak.
I'll stop and give it a few seconds and turn it again and it will normally start. But sometimes I'll do this 5 or 6 times and it will finally fire. But the more I have to try, it's like fuel builds in the cylinders and it smoke like a coal train for a minute or so. Almost like gas motor that has been flooded. But the smoke burns off and it runs like a top. I was thinking the batteries may be weak , but sometimes the starter will spin the motor with no trouble at all. I'm at a loss. Is it possible for fuel to drain from the system causing it to have to reprime itself? Here lately the smoking has me concerned even though it clears up.
View 7 Replies
I changed the IAC valve 2 months ago because my truck kept stalling when idling down on a cold start and that fixed the problem. A few days days ago when starting it started revving to 2 - 3 K and won't IDLE down now? I changed the IAC again and that didn't work. What else should I be looking at to stop it from revving so high?
2001 F250 5.4 111,000 miles super duty.
View 2 Replies
I have a 2001 F-250 XLT 4x4 with V10. Truck will not start. No fuel pressure. My Haynes manual does not show ignition or fuel delivery wiring. I have found the relay box behind the radio/dash. I need a wiring diagram and info on which relay is the fuel pump relay. Want to know so I can jump relay to see if fuel pump is okay.
Truck had sat for a few weeks being ran very little, so had to jump start yesterday. Ran for about 15 min, the shut off, re-started and ran for 30 min. Truck sat for about 1.5 hours then would not start. Charged battery overnight and it is 100%.
View 3 Replies
Truck was dead- 2001 F250 V10... Has a starter relay (solinoid) behind battery... put a new relay in there- no go- cleaner terminals... then I put key in start and shorted the 2 terminals in the relay and she cranked right up. That would mean the starter is still good correct?? something in the ignition system?
View 1 Replies
I have a 2001 Ford F-250 with the gas v-10. Yesterday it started just fine as always. Today I get into it and it starts to turn over just fine then starts to make a grinding sound and the truck won't start. I have had a fuel issue in the mornings with once it started you had to barely press the gass to keep it running. But never makes a funny sound and always runs fine. This only last for a couple of min and then it runs fine for the rest of the day. The grinding is not the starter. I took it off and had it checked and it was fine.
The truck had been using oil. When I checked the oil level it was low but it was still on the stick. "I know a motor needs oil to run smooth but it's my dads truck and well let's just say he is not the best on maintenance". Also I smelled the oil and it does have a gas smell to it. So it definitely does have some gas in the oil. I tried to light the dipstick with a lighter and it wouldn't light. So not sure how much gas is in it but that's what I did.
So the question is, would something just in mid crank go bad and then not let the motor crank. Truck made no weird noises before this so I find it hard to believe the barrings just went out in mid crank and now it is shot.
Also I just checked compression on front cylinders.
Driver side read 75lbs
passenger side read 100lbs
View 4 Replies
2001 F250 5.4 ... I'm losing my mind chasing a Gremlin. I've been having mostly intermittent starting issues with my truck. I've had the truck for a little over a year, after someone totaled my previous one.
It occasionally wouldn't start on the first attempt, but it got really bad in the last couple weeks.
I first thought it was a faulty inertia switch or wiring in that vicinity, as at one point after manually tripping and resetting the cutoff switch it would start, UNTIL I put the trim panel back. At this point I think that may have been a coincidence.
I eventually probed the switch and it tests as it should electrically.
I put in a new fuel filter and things were fine for several days, but it acted up again. That time was last Saturday. Got it to start and all was good until tonight. Now it won't go, and I've tried so many times that I can see the battery power is dropping.
Last Saturday I pulled the relays from behind the radio and cleaned 'em up real nice. Also, just to check another variable I swapped the two that matched.
I'm about ready to change the fuel pump, but I've heard so many people say they did that but the problem was something else. Not only will it costs hundreds of dollars, its cold out and we'll have to drop the tank in the driveway.
In addition to the relay, inertia switch and fuse, I have found some mention of faulty fuel pressure regulators causing issues. I'll pry the vacuum line off in the morning to see if I can detect fuel residue on the vacuum side. (There is some noticeable corrosion on the fuel rail in that area).
I REALLY want to make sure I rule everything else out before spending hours under the truck in freezing weather dropping the tank and changing the sending unit out.
On key-on there is a noise from the gas tank, but someone else listening described it as a click but no whirring.
I do hear the relay clicking behind the radio. (Also, I pulled them again tonight and put a meter to them. With 12V on the primary side, they click and the other side shows continuity on diode check, and about .2 Ohm on resistance mode.)
I went through a lot of trouble to get my spare out looking for the fuel control module before finding out my truck is about 3 years too old to have one too. What else to check?
View 3 Replies
Been driving my 2001 f250 7.3 4x4 with no problems then started noticing it lacking power so I changed fuel filter and air filter. After a week goes by I was at work and I was leaving to come home so I started truck to let warm up and it cranked longer than normal but started. Let run about 10 minutes idle nicely when I punched it it bogged down and had no power never died. I idled over into parking lot and power came so I took off again loss all power again, still never died. Got it right back to my work sat there a bit and tried again this time I took it easy and was able to get my truck home 30 so miles.
When I got home I ran codes p1211 came up for the icp sensor I changed it did not change anything still had same problem. This was a Saturday afternoon to evening issue. So sunday I played around with it just checking out info online and test driving it seem to run ok but still lacking power. Let it sit till Monday I went out to start it had to cycle key 3 time before it started idle nicely then died would not restart changed ipr valve nothing changed cam sensor nothing changed some how 10 quarts low in oil just changed dec. 30th don't know ? Now will start if I pump throttle and has all its power back?
View 1 Replies
Cold no start goes nowhere. I have a 2001 7.3 that will not start in the cold if I forget to plug it in....like last night. I have to plug in the block hater and give it a while before it will start. I tested the glow plug relay,it works fine. I can not find a test for the fuel bowl hear, and I'm not one to throw parts until I accidentally fix it. Any test procedure for the fuel bowl heater? Why this POS is so bad in the cold? Glow plugs tested fine at diesel shop in December, and this problem has been around since before that.
View 14 Replies
I would like to remove the tray located under the rear sit. I don't want anything installed back in place of it.I want the open space when the rear seats are folded up. I have two large dogs and they hate the tray. Will the rear sit ride okay if i remove the tray or will it loose some support?
View 8 Replies
Okay, so the truck is a 2001 F-250 Crew-Cab 7.3l PSD with about 300k on the clock. For a while now the A/C would start out okay when you started the truck and it would blow cold for about 10 minutes then it would start to fade away and get hot. Then later it might get cold again. You could turn the A/C off for a minute or so and turn it back on and it would be cold again.
Took it to a shop and they drained the system and recharged it and they couldn't find anything wrong with it. Well, it's still doing it. We were starting to thing maybe it was an electrical issue with the cold/hot switch on the dash until a recently noticed a pattern. If it had gone hot and I got heavy on the accelerator (revving above 2500 RPM), it would get cold and keep blowing cold for 3-5 minutes. So the trick to staying cool as of now is just to hammer down every few minutes.
I read the HVAC FAQs, and it seems like the issue maybe with a slipping compressor clutch. Sound right? Also if that's the issue, it says the solution is: Excessive A/C clutch gap due to clutch wear. Usually, the problem can be resolved by removing a shim from the clutch to bring the gap back into the desired .014-.030 gap. What exactly do I have to do? Where and what are these shims?
View 11 Replies
My starter solenoid keeps dying. I can't use a retail chain part. They burn up in a day. Always Motorcraft and it only lasts a year or so.
Any way to test this thing to see why it burns out prematurely?
View 9 Replies
I had a bad starter solenoid on the fender in my truck I swapped it out and then my starter went so I swapped it now it is not disengaging the starter If I turn the key to the run position it starts cranking and fires right up before I an let the glow plugs cycle or anything and it won't disengage the starter I turn off the truck and the starter is spinning loud for a couple seconds till it stops no matter if it just start the truck or start it and run it for a couple minutes then shut it off. 99 7.3L ....
View 6 Replies
My truck: 2001 F250 V8 Triton Automatic 4x4
Problem: 4x4 won't engage
Symptoms: No dash lights....nothing happens when I turn the 4x4 switch. When I start the truck I hear what sounds like a motor (transfer case motor maybe?) trying to switch (even though my dash switch is on 2WD)... It tries three times and stops.
What I've done: Checked fuses ...they appear ok to me
I don't have a maintenance manual yet ...
The 4x4 used to work up until about 2 weeks ago. Started having a hard time getting it to go into (and out of) 4x4 and then it just stopped all together.
View 3 Replies
I have been leaking oil on one of my work trucks. I do not know what the part is called or named. the leaks seems to be coming from above or behind a part that the driver side motor mount. As you can see in the image, the part has a sensor and a concave dip that runs along the middle of it. Well, I stuck my fingers behind that and it has a dip on the other side too which face up and that dip was puddled with oil. I need to know what that part is called or named or what is directly behind it that can be causing the leak. I hope its just a gasket and it is not cracked.
Part that is leaking behind. 2001 Ford F-250 Super Duty V10
View 1 Replies
I have an 01 f250 superduty bed is rusted what is the difference on a 04 f350 superduty dually bed to mine? Are they finished under the dually fenders?
View 3 Replies
