Ford Super Duty (1999-2016) :: 2001 F250 Powerstroke Will Not Engage When ESOF Switched To 4hi Or 4lo
Dec 18, 2010
The transfer case on my 2001 F250 Powerstroke will not engage when the ESOF is switched to 4hi or 4lo. I checked the fuses and they are good. I removed the electric motor on the side of the transfer case and while it was hanging down with the two plugs attached I did not see any movement when the dash switch was moved to the 4hi position. I used a wrench to manually shift the transfer case and still did not get the transfer case to engage. What next?
View 9 Replies
Advertisement
I am having some issues with my 2003 f250 6.0l 4x4. I cannot get the 4x4 to engage. There are no lights on the dash and no power to the switch other than the light. It doesn't matter if I have the hubs in lock or auto. It just seems like i have no power to the system. I have check all the fuses and they all check fine. I also check the transfer case motor and it seemed fine. I must be missing something. This truck is worthless without 4x4.
View 14 Replies
I am in the process of rebuilding my front end and have found that the nipples that screw into the top of the knuckles for the ESOF system are rusted and need replacing. I'd like to keep the system as close to original as possible, but have had no luck in finding a replacement. What the appropriate Ford part number is or where I could pick up a suitable replacement. This would be for a 2001 F-250 4X4 with the V10.
View 2 Replies
I have a 2001 F250 4x4 and the ESOF switch not engaging hubs, currently I have no 4x4 lights coming on in the cluster when i turn the switch. I am not experiencing any of the vaccum symptoms that most people are suggesting. I When I turn the switch i also do not hear any relays clicking. Relays have been tested, and i waited for the 45 second transfer delay that the manual mentions. ESOF switch has power, and is working properly (I know because I bought a new one in attempt to fix the problem) Basically I have no responses from any of my 4x4 indicators or parts.
View 14 Replies
My truck: 2001 F250 V8 Triton Automatic 4x4
Problem: 4x4 won't engage
Symptoms: No dash lights....nothing happens when I turn the 4x4 switch. When I start the truck I hear what sounds like a motor (transfer case motor maybe?) trying to switch (even though my dash switch is on 2WD)... It tries three times and stops.
What I've done: Checked fuses ...they appear ok to me
I don't have a maintenance manual yet ...
The 4x4 used to work up until about 2 weeks ago. Started having a hard time getting it to go into (and out of) 4x4 and then it just stopped all together.
View 3 Replies
I have an 01 f250 with a 4r100. Trans has not been slipping at all and yesterday it started a rough shift between 1st and 2nd. (3-4K Rpms) At the same time 4th gear stopped engaging. Shifts out of 3rd but does not go into 4th. I can hit my od button and it will shift back into 3rd and start pulling. Still no slipping just doesn't want to change 1-2 or engage 4th. I have done a full trans fluid change including new filter and tc. Old fluid looked fine with no metal flakes or garbage in it. So all new fluid still same problem. I was thinking of changing my shift solenoid.
View 9 Replies
A buddy of mine has a 99 F250, and the 4WD stopped working. The 4wd light in the dash does not turn on with the key with the rest of the lights. There is a Low Range light that does turn on. He took it to a shop/dealership and they said the vacuum was good. They also swapped in a different GEM module, which didn't change anything.
I swapped the relays under the hood - no change. I keep reading that there is a two wire plug on the transfer case I can test for voltage or to manually power the motor. Where is it? I see two plugs - the blue one on the left has 4 wires, the black one has more. Or is that not the shift motor I need to be looking for?
View 6 Replies
I have a 2000 f250 CCSB 4x4 with the ESOF auto hubs. The auto hubs won't engage automatically. They work fine manually. The transfer case is engaging and correct lights are coming on. There is a little bit of vacuum coming from the vacuum switch but it doesn't seem like much to me. All the dash HVAC controls work fine though. I Lubed and cleaned inside the hubs according to Guzzles directions.
While torn down, I blew through the vacuum port on the outside of the hub and there was little to no restriction. I don't think there is enough vacuum to pull the hubs, but is that possible if all the dash controls work fine? What pressure should it take to engage them? My next step is to pick up a vacuum pump and see if I can engage them with it.
View 6 Replies
A few months ago I had a battery go bad. When I started the 2004 F250 6.0 it barely started. After that my transmission gauge became the engine coolant gauge and the engine coolant gauge became the transmission gauge. I tried disconnecting batteries but that did not work. I have the Scan Gauge tool and confirm the gauges are reading correctly but just swapped. So I'm wondering if the is a reset procedure for instrument panel.
View 7 Replies
My 6.0 powerstroke will not start at all. I changed the rail fuel filter and the oil and oil filter. All oem for caps and filters. But the fuel filter in the engine bay is stuck. I didn't change the filter and I don't think I put diesel on the o ring to lube it. Could this be why it's not starting. I tried using starting fluid aswell no good
View 2 Replies
Can I take the tranny out of a v10 and put it in my 7.3L Powerstroke?
Both are 1999 f250's.
From what I've read they should both be 4r100's.
View 6 Replies
[URL] .....
Just got this truck a few weeks ago... cannot trace the oil leak. Is this common?
View 4 Replies
2005 F-250 King Ranch Diesel ... My truck when I got it the 4x4 wouldn't engage. I replace the front inner seals, and the lock outs. Still wouldn't work. Took the shift motor off and freed it up and it worked fin till today. Changed the shift motor and still nothing. This truck has been nothing but problems since I have had it and now this ... Truck is going on the market soon and would sell better if the 4x4 worked ...
View 13 Replies
F-250 2005 XLT 5.4L 4X4. Had ford for a few years now (Escape as a personal vehicle and econoline as business vehicle). Now I'm having a little problem with 4x4. It wont engage. Worked fine last week and now nothing! I did check all the fuses and when i switch to either 4Lo or 4Hi I can hear a clicking sound behind the switch but feel like it's getting blocked or something. Tries a few time then stop...
View 14 Replies
I have a 04 ford f250 superduty... I tried to use my 4x4 today and the front wheels would not engage using the ESOF. The light comes on in the dash saying its in 4x4. i do not believe i have a vacuum leak because it doesn't switch over to the automatic setting for defrost. what else could it possibly be I'm stumped at this point.
View 14 Replies
4x4 will not engage. 4x4 light on dash does not come on. Can not hear motor switching into 4x4. Check fuses under dash all looked good.
Truck is a 2004 F250SD V10 ....
View 3 Replies
I have a problem on my F250 4x4. The 4x4 doesn't engage from inside. I tested for vacuum on the pipe that leads out of the solenoid. There seems to be no vacuum building on the outlet line. This is the line that go to the wheels. Is my solenoid stuffed. the pump works well and vents do not default to defrost.
View 14 Replies
Basically I have a 2008 f250 (6.4l if that makes any difference) That wont engage into 4x4. When you go to turn the switch to engage the 4x4 all you get is a click click click click click. Is that a problem with the 4x4 shifting solenoid on the transfer case? Anything else to look for? The truck has 95k miles on it....
View 2 Replies
Starts fine most of the time. Then suddenly key will turn but not engage ignition. Power OK to everything but ignition. Have replaced starter & ignition module. Still does the same thing. Leave for a while & truck starts fine. 2006 F250 6 litre diesel ...
View 1 Replies
About a month ago I bought a 2004 F-250 160xxx from a reputable Ford dealer here in town. The dealer performed a safety and emissions inspection, and spent about a grand on other repairs, as a condition of my purchase. Today I had it in the shop for an instrument cluster issue (at a different Ford dealer, closer to my house), and was told the vacuum lines were all messed up. Their write up is below:
"Check 4x4 operation. Transfer case shifts to 4x4 and 4x4 low. Front hubs do not engage automatically. Check vacuum at the hubs. No vacuum. Check the vacuum at the solenoid. No vacuum. Perform visual of the engine vacuum lines. There is no vacuum to the reservoir. Vacuum line is routed wrong from the fuel pressure regulator to the vapor management valve. There is other vacuum concerns. All of the vacuum line routing needs to be inspected and corrected."
The service rep told me it is questionable whether the 4x4 ever worked, although during the few weeks I've owned it, I could hear gears or other mechanical parts making noise which seemed to me to be in response to me turning the 4x4 electronic switch. She also said there was a vacuum line dangling loose with a screw in the end of it.
Before I contact the dealer where I bought the truck, I am planning my going-in position. But I wanted to get a sense of a) how serious of a problem this might be? and b) how reasonable it is that the dealer didn't catch this issue before I bought the truck while they were in their fixing other things?
The dealer who sold me the truck made it very clear that the sale was as-is, and I took it to my mechanic prior to purchase, though unfortunately he only had time for a cursory look at the engine. Obviously he didn't look closely enough to find this issue.
I'm not sure if I should ask the dealer who sold it to me to fix it, or ask them to allow me to return it, or sell it back to them, or if I should eat the cost of fixing it. How wrong would it be to try to trade it in for something else?
View 3 Replies
I have a 2000 f250, 5.4l triton v8 that cranks like crazy, but won't start. When I spray a little starter fluid in it it will run until the spray wears off. Brand new battery and full gas tank. it does have check engine light on dash, probably from the o2 sensor as the exhaust has almost completely rusted out. Also on a side note the cruise control will not engage.
View 6 Replies
