Ford Super Duty (1999-2016) :: 2001 F250 - Engine Will Not Warm Up
Apr 8, 2014
Its a 2001 f250 with a 5,4. I just recently put a new shot block in it, the short block is a svt short block for an 01 lightning. every thing off old motor went on new svt block just fine, and it drop in just fine. only it will not warm up i let it run for 45 min the other day and on the gauge it would not come past the c. and i do believe the gauge to be accurate because the heat in the cab sucks and the top rad hose is just warm, not as hot as it should be. I've already put 2 new thermostats in it so I don't believe that to be the issue either.
View 14 Replies
Advertisement
Sunday I bought a 2001 f250/5.4 to replace my 91 f250. I didnt drive it yesterday, but this morning on my drive to work the heater was very weak, it seemed to blow warm for the most part, but was barely pushing air even on high. I flipped it over to A/C to see if it blew any harder and it did. Does the blower motor need replace? if so why does the AC blow harder than the heater?
View 14 Replies
Truck is a 1999 F-250 with manual climate control with A/C.
Heater core issue:
Heat is not very warm after engine is fully up to temp. Would like to back flush the heater core without damaging or making it leak. How should I do this safely?
Secondly, if I do make it leak, how hard is it to change out?
View 4 Replies
I can't seem to get the engine temp to middle range on the marker, but yet my heater blows "to me" hot air. Even while sitting in idle for extended amounts of time I cannot get it to "operating" temperature. I would think if my thermostat was stuck open my heater would blow either cold or slightly warm air. I have the 5.4L engine with knn air filter and no cats.
View 14 Replies
2001 f250 5.4L v8. Engine temp seems really low. The gauge is reading barely above the cold in normal range. The heater is only blowing out 75 degree air at the warmest. It gets to its normal temperature with in 15 minutes even when its real cold out. I live in Minnesota and its been a really cold winter so having hot heat would be nice. I just bought this truck at the beginning of the winter. Whats going on?
View 14 Replies
I have a 2001 f250 with the 5.4 I replaced the belt because of belt squeal and after replacing it the squeal is gone. now after the truck gets to its normal temp and I stop at a gas station for dip I will leave it running and when I come out it has this loud chirping noise it kinda sounds mechanical but it very well could be something on the belt drive. I am stumped it goes away after I start driving but I am kind of nervous about what it could be.
And the only time I hear it is while the truck is at normal temp and in park I have rolled the windows down and can not hear it while driving or at traffic lights. a part of me says it could be the fan clutch and now that it has a good belt on it I am hearing a sound of maybe the clutch going out or a pulley bearing starting to go out. Where I should go from here?
View 11 Replies
I have an 2001 F-250 5.4L.
It has the Triton engine and the problem with spark plugs blowing out. I have a kit with thick inserts that I'm going to install. I need to drill and tap the heads, but first I need to get the piston in the cylinder I'm working on to get close to the bottom and have all the valves shut. But I can't manually turn the engine over. I tried using a long ratchet with a socket that fits the nut on the crankshaft pully, but the nut just seems to tighten more, instead of turning the engine over.
And trying to turn the fan pulley doesn't do it either. Also, using the electric start for a split second at a time still seems to turn the engine over too quickly for me to get the piston where I need it. Do I need to pull all the spark plugs to do this? I really just wanted to work on one cylinder for now, instead of opening up a can of worms.
View 6 Replies
I have a 1999 F250 7.3 Diesel and my AC isn't working properly. On Max AC as you're driving it would be ok and then it would be warm and then cold and then warm and then cold and so on. I've noticed that the clutch stays engaged as well. I've never seen it disengage. The freon is at the level it needs to be. Then just a few days ago, if you have it on Max and High the air disappears from the vents and you hear a noise somewhere in the dash on the passenger side. I think something might have come off?? What's wrong with my AC with it going from cold to warm constantly? I heard that maybe clutch has too big of a gap?? I have almost 200,000 miles on it.
View 6 Replies
I have 1700 miles on my truck and the A/C cycles between cold and warm air. I have taken it to 2 Ford dealers and they agree there is something wrong but their tests are apparently up to Ford specs. They logged complaints with Ford and they were told this was by design with the new trucks and it was normal for the compressor to constantly cycle. New 2013??
View 2 Replies
2004 F250 V10, runs good until it warms up whether it's hot or cold outside. While on freeway, it really shakes while cruising, but of you get in the gas enough for a kick down, seems to be pretty smooth. I've changed the coils, and 9 plugs (one wouldn't budge, but the others I took out looked fine) to no effect. Where else should I look? Also, no CEL, and no codes, which seems odd as bad as it feels...
View 11 Replies
My idle goes real fast 2500 rpm special when is warm can't get idle to go down for nothing took truck to camping on dirt road with the vibration idle came back to normal and stay for while and over the soon start again. No code...
View 1 Replies
I am the proud owner of a 2002 F250 Super Duty 4x4, which has 158K miles on it. I live in South Florida and use the truck as my daily driver and also from trips up into the Blue Ridge Mountains.
Recently, I noticed that when I have the A/C on it blows nice and cold for about 15 minutes, but then the air gets really warm. I had the system checked and the Freon levels are right where they should be. A bit of experimenting reveals that if I turn off the A/C for about 10 or 15 minutes after it starts to blow warm air, the systems blows cool air as it is supposed to.
Therefore, I suspect that something is freezing under the hood and preventing the system from operating properly. Since A/C is pretty well essential for us in south Florida, this is a problem, when I have the family or customers in the truck.
View 2 Replies
The truck is in my Sig 01 F250 5.4
Just got back from a long trip with it. Parked it for 3 days, all was running fine. Went to dinner Sat night and all was great, left the restaurant and as soon as I started the engine I noticed a slight vibration. As soon as I hit 42 miles per hour, it started shaking pretty good. I pulled over and checked under the truck to make sure I did not have anything I was not supposed to hanging down.
Driveshaft looked good, nothing leaking from rear end or tranny. When it does vibrate, the Tach shows the unhappiness as well. This a.m. driving to work it was vibrating at all speeds and shifting was very rough, had a hard time deciding if it wanted to be in second or third gear. I don't think this is drive train issue... When it shutters and sputters at 40ish MPH, its almost like it loses power and I have to let off the gas. and then under power it shakes badly.
I had the super chip settings for performance tow when this started and then I changed it back to stock settings, thinking it might work, which it only got worse. Changing the settings with the Superchip you have to disable the fuel system and I do this by pulling the fuel pump fuse under the hood in the power distro box.
I think the ujoints are still good, the oil and tranny fluid are spot on. Hubs are locked but in 2WD. Had all the front end replaced 15K miles ago. Brand new tires and wheels in Sept, front end alignment done at same time, front brakes were 90% and rear brakes at 20%.
View 10 Replies
I have a 2006 Ford F-250 5.4l the symptoms are when it's warm it has half power and it will stall at idle. What I have done with the truck is.
New cam phasers
new chain
new tensioners
new vct solenoids
new oil pump
new plugs
new ignition coils
new stock cam shafts
new rockers
new lash adjusters
new exhaust manifolds both sides
new muffler
oil change with the right oil
ran it with sea foam in the crankcase before oil change
new fuel pump module
new evap vent control
new abs speed sensor
I cleaned throttle body with brake cleaner ... Scanned it after a 15 min ride of having to use 2 feet to drive it. The engine codes that came up are p0022 iacv short to ground and p1000 readiness test not complete. I also got p1804 4 wheel drive high indicator circuit failure p1808 4 wheel drive low indicator circuit failure .... Not sure what else to try.
View 7 Replies
Okay, so the truck is a 2001 F-250 Crew-Cab 7.3l PSD with about 300k on the clock. For a while now the A/C would start out okay when you started the truck and it would blow cold for about 10 minutes then it would start to fade away and get hot. Then later it might get cold again. You could turn the A/C off for a minute or so and turn it back on and it would be cold again.
Took it to a shop and they drained the system and recharged it and they couldn't find anything wrong with it. Well, it's still doing it. We were starting to thing maybe it was an electrical issue with the cold/hot switch on the dash until a recently noticed a pattern. If it had gone hot and I got heavy on the accelerator (revving above 2500 RPM), it would get cold and keep blowing cold for 3-5 minutes. So the trick to staying cool as of now is just to hammer down every few minutes.
I read the HVAC FAQs, and it seems like the issue maybe with a slipping compressor clutch. Sound right? Also if that's the issue, it says the solution is: Excessive A/C clutch gap due to clutch wear. Usually, the problem can be resolved by removing a shim from the clutch to bring the gap back into the desired .014-.030 gap. What exactly do I have to do? Where and what are these shims?
View 11 Replies
My truck: 2001 F250 V8 Triton Automatic 4x4
Problem: 4x4 won't engage
Symptoms: No dash lights....nothing happens when I turn the 4x4 switch. When I start the truck I hear what sounds like a motor (transfer case motor maybe?) trying to switch (even though my dash switch is on 2WD)... It tries three times and stops.
What I've done: Checked fuses ...they appear ok to me
I don't have a maintenance manual yet ...
The 4x4 used to work up until about 2 weeks ago. Started having a hard time getting it to go into (and out of) 4x4 and then it just stopped all together.
View 3 Replies
I have been leaking oil on one of my work trucks. I do not know what the part is called or named. the leaks seems to be coming from above or behind a part that the driver side motor mount. As you can see in the image, the part has a sensor and a concave dip that runs along the middle of it. Well, I stuck my fingers behind that and it has a dip on the other side too which face up and that dip was puddled with oil. I need to know what that part is called or named or what is directly behind it that can be causing the leak. I hope its just a gasket and it is not cracked.
Part that is leaking behind. 2001 Ford F-250 Super Duty V10
View 1 Replies
I have an 01 f250 superduty bed is rusted what is the difference on a 04 f350 superduty dually bed to mine? Are they finished under the dually fenders?
View 3 Replies
Having trouble with the truck going into gear. It started by having to put the truck in first and manually shift until in drive, once it finally engaged and would drive normal. But now im having trouble with going into gear at all. What could be the issue????
View 8 Replies
2001, F250, Lariat, Super Duty, 7.3 engine with towing package.
It ran seemingly perfect when I parked it and it sat for maybe 10 days to 2 weeks and wouldn't crank. Battery is fine and fully charged. Glow plug heaters work OK. Engine spins really fast, almost like it had no compression. (Not sure though) Temperature in the 30's -50's. I did some research on line and decided to change the Cam Positioning Sensor (CPS). Didn't work, still won't crank. I originally tried my Cheap Harbor Freight OBDII . (Don't waste your money, IMO). What should I troubleshoot next/ or try.
View 5 Replies
I have a vibration in my 2001 f250. At about 45 to 55 it vibrates. I have changed u joints in the rear drive shaft. Pulled it again tonight. U joints look good, no play. I am going to pull the front shaft and see if it makes a difference. I did notice some play on the rear shaft where it slides. Could this be causing the problem?
View 4 Replies
