Ford Super Duty (1999-2016) :: 2001 F250 - Driver Side Window Stopped Working?
Aug 24, 2015
My drivers window will not work at all but when I push the button I get a clicking in the fuse box. The other 3 windows partially work but will only go up or down in small increments. I have tried holding the button and slamming the door and this allows the other 3 windows to work. I thought it was the switch so I replaced it and that was not the problem. Fuse and relay seem to be fine. If it was just the driver window I would think it was the lift motor but with the other 3 windows on the fritz I have no clue.
View 1 Replies
Advertisement
I have a 1999 f250 crew cab. About 6 months ago my drivers side window quit working in the up position(lucky me) and last week I got around to fixing it . I just ordered a new window motor instead of the whole regulator and installed it and it worked perfect for 4 days and today it suddenly quit again. What would cause a window motor to go out again so quick? Everything else seems to be fine and there is power to it so I'm assuming it's the motor.
View 2 Replies
here's the problem. The driver side front power window will only go down and not up. I checked the motor and the master switch with a multimeter and both work just fine. the motor is receiving power and the master switch is sending power. However when i plug the motor back in and re-install it, the window will not go up. Is there some sort of relay that might have gone bad that is not letting the motor raise the window up???
View 5 Replies
I'm hoping this might be a "quick fix". Got in the truck the other day and my power driver's seat had no function what so ever. Not a big deal for me as I drive with the seat all the way back but the complaints are starting from my wife so it's time to find a fix.
This is the first F250 I've had so the wiring is a little new to me. I checked the fuse panel and the fuse seemed okay I swapped #9 out for #22 as they are both 30A and I don't need the trailer at this time but still no luck.
Are there any other systems tied into the driver's power seat, any wiring harnesses I should check or perhaps a fuse that is not shown in the owner's manual? My truck is the 2013 Gas F250.
View 2 Replies
On my way home today I heard wind coming in around my drivers side power window. Its not seating itself straight in the weather stripping. The window is tilted toward the front of the truck. Do I need a new regulator? Or maybe re- epoxy glass to bracket? The window still operates, its just crooked. Also I haven't had those door panels off before..
View 1 Replies
I have a 2001 F250, 5.4, 4X4. My ignition key stuck in the start position and when I pulled it back to the run position, everything seemed ok. As I started down the road, my speedometer stopped working and my overdrive light was flashing. Also my turn signals had stopped working and my A/C clutch didn't engage. Figured I burnt a fuse. I looked in both the under dash and power distribution box and all seemed well. I checked the fuse for the turn signals/flasher and it was fine. The flashers worked. Thought I might have fried something so I replaced the ignition lock and switch. Also my service engine light came on throwing a code for the vehicle speed sensor.
Looking for solutions on this forum and the internet, I learned that the turn signal switch could have gone bad and the VSS sensor is on the top of the rear dif and an easy fix. Well replaced the sensor but nothing changed. So I went back to the fuse box. Examined every fuse, big and small and I found a 10a with a small space. This was #24 under the dash. From the manual, "#24, 10A, A/C clutch, Blend Door Actuator, Trailer Tow Battery Charge Relay Coil, Four Wheel Anti-Lock Brake System (4WABS), Turn Signal." Replaced it and everything went back to normal. Turn signals work, A/C clutch works, no flashing overdrive light and speedometer works. All from a 10A fuse. If you have any of these symptoms examine all the fuses carefully. There's a 20A fuse for turn/hazard lamps and this other one buried that's only 10A.
View 1 Replies
Here's the deal. I have a 2001 F250 4x4 and I am getting a noise in the front drivers side wheel. The noise is not a grind or clunk, but its like a u-joint is rubbing inside an empty cylinder kind of. Anyways, it seems like it does it only with small bumps. I took off my oem hubs and re-installed them and the noise went away for about a week. Now I replaced them with manual locking hubs and the noise is back. One other thing I notice is if i put the switch to 4x4 the noise goes away. I checked all major components for the steering and suspension and nothing was loose. The front end is tight. Is there anything inside the axle that would cause this? I dont know what to check for anymore. Where else to check?
View 4 Replies
I have a '01 F250 with a frozen u-joint in the driver side front axle. My question is can I put it together without the axle and drive it?
View 2 Replies
1999 f250 passenger window went down but will not go up. Neither switch will make it go up. I was wonder if both switch could have went bad? Any way to test a switch?
View 4 Replies
2012 f250, fog lights stopped working and tried fixing yesterday. I'm getting 12.8v at the plug but as soon as you plug the light in it goes to 0. Ran a new ground from frame and the hot from plug and still nothing. High beams off, truck running and switch pulled out. Bulb is fine, hooked it straight to battery and it comes on. I though it was a faulty ground but by running a separate ground and still nothing. I'm at a lose.
View 2 Replies
Just picked up a 2001 Gas F250 4X4 XLT. Everything seems to work except for the electric windows and ABS. I pulled both window switches and cannot find any voltage on the Blue/black cables. I jumped 12v to the drivers side switch and the windows work up and down even in auto. I have voltage at the 30a circuit breaker in the PDB but nothing at fuse #7 in the PCFP. I've checked for voltage at another connector with a Blue/black cable and found nothing. I'm thinking bad cable or GEM. I have noticed that the bell system doesn't sound when you have the key in the off position with the door open if that matters.
View 14 Replies
I have an F-250 diesel 2004 and about six months ago it started acting really crazy. Basically most all of the dashboard electronics stopped working like the speedometer , odometer, gauges, etc. additionally all of the interior lights, and the radio stopped working. Now it looks a lot like the attached picture when I'm driving the truck. All of the lights are lit up on the dash panel but nothing actually works. I thought at first that a bunch of fuses might be blown but I have replaced nearly every fuse that has anything to do with any of the affected systems. What the issue might be.
View 11 Replies
I have a 2003 F250, 4x4, 5.4L and today my fuel gauge stopped working. I don't know if it had anything to do with a stall, I was on an exit ramp and the truck cut off, I quickly restarted and no issues after that. Other than the fuel gauge not working at this point.
I looked at the fuse panel diagram and there is no fuse for just the fuel gauge. The only thing I see is #35, instrument cluster. The rest of my instruments are working, so what else would cause the fuel gauge to stop working? It had a little over a half of a tank before the stall, after the stall it went down to less than half. I filled up shortly later and it's just stuck at less than half.
View 1 Replies
A buddy of mine has a 99 F250, and the 4WD stopped working. The 4wd light in the dash does not turn on with the key with the rest of the lights. There is a Low Range light that does turn on. He took it to a shop/dealership and they said the vacuum was good. They also swapped in a different GEM module, which didn't change anything.
I swapped the relays under the hood - no change. I keep reading that there is a two wire plug on the transfer case I can test for voltage or to manually power the motor. Where is it? I see two plugs - the blue one on the left has 4 wires, the black one has more. Or is that not the shift motor I need to be looking for?
View 6 Replies
My door locks stopped working new battery in fob, I can hear them trying to work. 2000 f250 crew cab .....
View 3 Replies
As the title says, I have an intermittent issue with the power window in the driver's door. It always works, with the exception of when it gets really damp during the night. In that case when I get in the truck first thing, the window will go down, but not always up the first few tries.
View 1 Replies
So one day my 4 wheel drive just stopped working, when I put in 4hi nothing same with low, the light on the dash doesn't even pop up and it doesn't engage. I've done about everything I could think of doing besides replacing the motor for it and the wiring, I hate getting stuck...
View 4 Replies
On the F250 trucks, if I changed the mounting frame under the seat, will the passenger side seat fit on the drivers side? Basically, can I turn a passenger seat into a drivers seat?
View 4 Replies
2001 F250 SD 7.3 PSD Was doing a trailer towing road trip too and from Montana. On the way back the cruise control stopped working. Checked fuse #28. Looked fine. Attempted to do a self test on the cruise control. Holding the OFF button did nothing. Never went into diagnostic mode. Button ? A different fuse?
View 14 Replies
My father-in-law has a 2008 f-250 with the 5.4. as he was driving a while back all the gauges of the dash quit. The engine still kept running without any noticeable difference but when he shut the engine off and tried to restart, it wouldn't even crank but the security light was flashing. He tried starting it again a few hours later and it started just like normal and ran fine.
He has had this problem occur several times in the last few months, but the other day it repeated the problem again and would not restart for about 5 days. He has tried charging the batteries, changing relays, checking all fuses and finding none blown, scanned it with his code reader, and checked the steering column for bare or rubbed wires.
View 10 Replies
I have a 2001 F250 with 7.3.... We swapped the auto for a zf6 manual.... We left the auto's shift position sensor tied to the frame and left in neutral. I did install a pcm from a manual transmission pickup. Also have the clutch position switch hooked up. I have an Edge Evolution CTS2 reprogrammer, and on the display the gear indication always shows P. I suspect that is why my cruise doesn't work. For interests sake, I tried manually adjusting the shift position sensor through all gears, and the reverse lights come on when in reverse but the Edge's display always shows P. My question is with a manual transmission, how does the pcm know that it is in gear? The only sensor that I am aware of is the reverse sensor on the zf6.
View 2 Replies
