I've just bought 2001 f-250 crew cab and when I push the cruise control on the steering wheel it does nothing. Maybe a fuse or does my year have one of those master cylinder switches?
View 12 Replies1999 F250.. What would cause my cruise control to work sometimes and not others. it may work today and not tomorrow.
View 2 Replies2000 F250 Super Duty cruise control not working. I looked through a lot of threads on this subject and cannot pin point my problem. Cruise control was working, had to slow down wile approaching a town, back on the highway and now it won't turn on.
Looked at the brake pressure switch, it was till good but was the old type but had the recall harness on it. Bought a new one and replaced it anyways. Still nothing. All my brake lights work, I also did the Cruise control diagnostic and it passes everything. No lights on my dash are on, speedometer works, horn works.
The only thing I did not check is the Vehicle speed sensor. Even though my speedometer works and my ABS light is not on, can this still be the problem? If so how do you test it? Do I just remove it and test continuity?
I have a 2003 F250 Super Duty 5.4 crew cab. Cruise light comes on when engaged but does not work. I did some research on why its not working checked wiring at the throttle body it seemed ok, Fuse is ok. Also did the self test and everything passed with just one flash but cruise still does not work. I read about many problems with the brake pressure switch but would it pass the self test if that pressure switch was bad? Also what should a switch cost. Local dealer wanted $125.00 for a new one and I have read where they cost around $15.00 - $20.00.
View 12 Replies2001 F250 SD 7.3 PSD Was doing a trailer towing road trip too and from Montana. On the way back the cruise control stopped working. Checked fuse #28. Looked fine. Attempted to do a self test on the cruise control. Holding the OFF button did nothing. Never went into diagnostic mode. Button ? A different fuse?
View 14 RepliesI have a 2001 F250 with 7.3.... We swapped the auto for a zf6 manual.... We left the auto's shift position sensor tied to the frame and left in neutral. I did install a pcm from a manual transmission pickup. Also have the clutch position switch hooked up. I have an Edge Evolution CTS2 reprogrammer, and on the display the gear indication always shows P. I suspect that is why my cruise doesn't work. For interests sake, I tried manually adjusting the shift position sensor through all gears, and the reverse lights come on when in reverse but the Edge's display always shows P. My question is with a manual transmission, how does the pcm know that it is in gear? The only sensor that I am aware of is the reverse sensor on the zf6.
View 2 RepliesJust bought the 03 listed in my signature line, and I just found out that the cruise control isn't working, so started trying to troubleshoot anything obvious.
When I switch it on, I get no cluster light that the manual shows to be to the right of the brake light. When I turn the key to run, it never lights up, so am guessing the bulb is bad.
Can't see how a bad bulb would keep the system from activating, so am thinking I have bigger issues. I pulled the fuse panel, but the manual does not have a listing for speed control. Which fuse it is combined into?
Also need the skinny on how to change the bulb. Can I reach my hand behind there? does the cluster have to come out?
Last question. What is the most likely culprit for non functioning cruise? A module? Perhaps the switch in the steering wheel?
Our cruise isn't working, I've read through the posts here and tried a few things
2000 F-250 V-10
-First symptom was the cruise light would light with the ON button and go off with the OFF button but I could not set the speed with the SET button. Now the cruise light hardly comes on at all any more.
- I've run the cruise self-test diagnostics and all the switch presses passed with no additional light blinks. After the static test the speed control servo makes a sound but does not move the throttle at all.
-The horn works
-Fuses are good
-Truck was taken to the dealer several years back for the cruise update. The pigtail with the green label is installed at the master cylinder. I've disconnected both connections and sprayed with contact cleaner.
That's about it. What it could be or what to test next?
I have a 2001 F-250 SD XLT with the ABS light on, cruise control doesnt work and the horn only works with the key out. The codes for the ABS is no signal input from the left and right front wheel sensors. No problem there. Also my speedo stops or jumps when I press the horn button while driving down the road. When I quit pressing the horn button the speedo works fine. So after looking over the posts on cruise control, etc. Does the rear speed sensor have anything to do with the cruise, horn not working? All fuses are good so I am thinking the cruise control switch on the master cylinder or a short in the steering wheel column or my ignition switch. What do you all think?
View 7 RepliesI have a 2003 f-250 5.4l and the cruise control quit. If you press the on and coast it will honk the horn so I am thinking switches on the steering wheel or the clockspring. I need to test those. Everything else works fine....
View 6 RepliesJust bought a 2003 5.4 6 speed 4x4 F250 .. The cruise control does not work at all. The only fuse I can find in the owners manual is a 2 amp one .. it is in good shape .. Where do I look now to solve the problem??
View 8 RepliesThe latest addition to the driveway (2012 F250 XL 6.2) is getting ready to be geared up for it's tour of duty. The one thing that was on the would-be-nice but not must-have list was cruise control. This truck doesn't have it, which wasn't a deal breaker because the truck was way inside my budget.
So anyways, while researching hitches, tonneau covers, steps, etc. I came across this : [URL] ....
Is this all I need to install the speed control? I would assume the dealer would have to get into the logic and enable something, but is this switch really all the hardware I need to buy?
Was hoping to get confirmation on a fix I intend to repair.
2000 F350 SuperDuty 7.3l Diesel 4x4
Cruise isn't working...... lights won't even come on and nothing happens at the switches.
This morning I put in a new airbag clockspring ...... just requires patience but not too hard to do.
That didn't resolve. Was going to put in new cruise switch at the brake master cylinder.
My question is would that part prevent the cruise control from even turning on at the steering wheel controls? I don't get any light or anything when I hit "on".
I checked literally every fuse in the under dash and under hood boxes. All are good. Is it likely it's the cruise switch?
2004 F-350 6.0 4X4 Manual transmission. When I drive on the freeway I can turn on the cruise system w/ the On switch. When I then use the Set button the green dash light comes on but immediately goes off when I release the button. Hold the button, the green light flashes until the button is released.
If I push in the clutch peddle while coasting down a hill and attempt to turn on the CC the light does not come on. Similarly with the brake peddle depressed. Periodically the ABS light comes on and I can tell by the brake peddle feel there is an issue with the ABS.
Additionally, the speedo is not accurate. I have an aftermarket GPS. When driving with traffic in a 65 I am reading about 55. My GPS confirms the speed of 65. The speedo flutters with about a 5 MPH span.
Yes, I have tried the Cruise Control Self diagnosis. It does not work on my truck. Key on w/Off button depressed and nothing.
I have checked for codes w/ Auto Enginuity. C1229 & C1184 both come up.
I have replaced the Vehicle Speed Sensor at the top/front of the rear differential.
I have replaced the Cruise Control Cut out Switch on the master brake cylinder.
Both parts are from Ford parts department.
So... What now?
For about 6 months the cruise control on our '09 F-250 has been intermittently failing. One time I'll set it and it will work fine, the next time I try to set it and it fails. No particular rhyme or reason to when it fails to set.
Some of the tests that I did indicated it was the brake light switch on the brake pedal arm. It seemed to work perfectly a few times that I drove it after the installation but now it's back to working when it wants to.
I had a problem with the cruise on our '06 Ranger and it turned out to be the module. It acted a bit the same way in that it would set sometimes, other time not. I don't know if the two systems are similar or not.
Truck is an 02 F250 Automatic 4X4, 7.3 PSD.
Cruise control will turn on, will sometimes set speed and sometimes will not. If it does set and work it may kick off at any second or it may run fine. I have noticed it seems to kick off mainly after going over a slight bump in the highway or it may just kick off for the hell of it. Truck has 50,000 miles on it, I bought it new. Also having trouble with the throttle position sensor, it seems to have a "dead spot" at about 58 mph that shows up when I romp down on the pedal to pass on 2 lane roads. Can these two symptoms be related? Both are very aggravating. FWIW it does have the power adjust pedals. Truck is 100% stock, no power chips or other upgrades.
I have an early 1999 f250 diesel. I originally googled having the airbag light on and loss of cruise control and came up with it more than likely being a bad clock spring. So I replaced the clock spring, and it was definitely blown. I have a horn now, not sure if I did before or not, but still the light is on and no cruise control. The airbag light is flashing code 27 which I believe means the passenger airbag has issues.
So I tried turning the key in the switch for the passenger airbag to deactivate it, but it only lets me turn it 45 degrees and no light comes on. It looks like the key should turn 90 degrees but maybe I'm just an idiot. I see a lot of people with the bulbs dying and running into issues but that wouldn't explain the inability to turn the key 90 degrees. Also would the airbag light being on deactivate the cruise or is that just some other issue? For what its worth, I plugged in a code reader and no codes came up, just the flashing airbag light.
I have a 1999 Super Duty 5.4l Manual transmission 4x4 105,000 miles the cruise control stopped working a month ago, I didn't think much of it because I frankly don't use cruise as this vehicle is usually used to tow and I don't run cruise towing.
Long story short I went to tow my camp trailer and noticed my brake controller was not actuating the trailer brakes when I braked, the controller is showing connected and when I manually actuate the controller its working, so I knew I had a brake light issue, I checked the brakes and sure enough I have no functioning brake lights.
I bought a Motorcraft OEM brake pedal switch and replaced it to no avail,I have also checked the applicable fuses they are fine. I have a master cylinder cruise control switch to change but have my doubts this is the issue since the brake lights and cruise are non functional.
2002 f350 7.3 diesel automatic. The cruise stopped about a 1/2 year ago and i have done the recall and replaced the steering wheel switch. but it still doesn't work. the horn works and speedometer works.
View 4 RepliesI have a 2000 f250, 5.4l triton v8 that cranks like crazy, but won't start. When I spray a little starter fluid in it it will run until the spray wears off. Brand new battery and full gas tank. it does have check engine light on dash, probably from the o2 sensor as the exhaust has almost completely rusted out. Also on a side note the cruise control will not engage.
View 6 RepliesCruise won't power up. Tried entering diagnostics but did not get any flashes. By-passed switch on master cylinder, did not make any difference. Horn honks. Brake lights work correctly.
View 9 Replies