Ford Super Duty (1999-2016) :: 2001 F250 4x4 - Getting Noise In The Front Driver Side Wheel
Apr 11, 2013
Here's the deal. I have a 2001 F250 4x4 and I am getting a noise in the front drivers side wheel. The noise is not a grind or clunk, but its like a u-joint is rubbing inside an empty cylinder kind of. Anyways, it seems like it does it only with small bumps. I took off my oem hubs and re-installed them and the noise went away for about a week. Now I replaced them with manual locking hubs and the noise is back. One other thing I notice is if i put the switch to 4x4 the noise goes away. I checked all major components for the steering and suspension and nothing was loose. The front end is tight. Is there anything inside the axle that would cause this? I dont know what to check for anymore. Where else to check?
View 4 Replies
Advertisement
I have a '01 F250 with a frozen u-joint in the driver side front axle. My question is can I put it together without the axle and drive it?
View 2 Replies
My front driver side wheel is making a clunk noise when I hit a bump. I replaced the wheel bearing hub assembly and discovered both axle seals were bad.
View 10 Replies
Got off the freeway today, driving along about 40 or so thought I smelled something hot like something burning. Stopped in a parking lot and smoke was rolling out from drivers side rear wheel. Look under and oil is dripping from inside of the wheel. Figure the caliper was hung up and got so hot it took the seal out. I can't get to it right now and the shop says I can't get in until next week, need my truck now. How long could I get by the way it is IF I take it real easy.
View 9 Replies
Cat like noises coming from front driver side tire .. honestly sounds like a cat ..it gets louder the faster I go ... what it could be ?
View 7 Replies
here's the problem. The driver side front power window will only go down and not up. I checked the motor and the master switch with a multimeter and both work just fine. the motor is receiving power and the master switch is sending power. However when i plug the motor back in and re-install it, the window will not go up. Is there some sort of relay that might have gone bad that is not letting the motor raise the window up???
View 5 Replies
Had the death wobble a couple of months ago. Changed all shocks, steering stabilizer to bilsteins; new tires (stock), ready lift stabilizer(stock, no lift) had it digitally aligned. All was perfect. Until my new intermittent steering issues. It appears to happen when making a 90 degree turn, say a right or left onto a perpendicular roadway. As truck straightens out, you'd think the front drivers side wheel is going to fall off(you'd think the lugs are missing).
Pull int a parking lot, drive in a few circles, and all back to normal. Can't replicate every time, force for s few days with no issues, then it might happen again. Other intermittent issue is sometimes, again out of no where, truck will pull and track to the right or left. Pull the steering wheel the opposite direction, it'll track the other way. Again, pull int parking lot, do a few figure eight circles and back to normal. Alignment shop and regular mechanic say everything is tight, ball joint look fine.
View 3 Replies
I have a 2003 F350 srw 6.0. 4x4. Front driver side wheel bearing went out. Went to the auto parts store got a replacement. Got it all tore apart, put the new one on and the lockout didn't seem to fit right. Is there a difference in wheel bearing assemblies for electronic shift on the fly and regular lockout? I have the electronic shift on the fly lockouts and it had just a little bit of play in it when I put the snap ring back in.
View 3 Replies
My drivers window will not work at all but when I push the button I get a clicking in the fuse box. The other 3 windows partially work but will only go up or down in small increments. I have tried holding the button and slamming the door and this allows the other 3 windows to work. I thought it was the switch so I replaced it and that was not the problem. Fuse and relay seem to be fine. If it was just the driver window I would think it was the lift motor but with the other 3 windows on the fritz I have no clue.
View 1 Replies
So I'm away from home on vacation also away from my tools. Any ways my front drivers side line busted almost causing me to crash earlier today in my 2006 F250 6.0 diesel 4x4. So basically my question is: what tools are needed to do this job? I've already picked up the part now tomorrow morning I will be changing the part...
View 2 Replies
I need to replace the front passenger side wheel hub unit on my 2012 F250 4x4 120,000 mile reg cab truck. Its been a while but I did one on my 2000 F250 without any problems. There should be a few clips inside the hub that hold the looking hub and shaft together, right? Do I need any special tools for this job? What do the bolts need to be torqued to?
View 2 Replies
2002 F250 4 wheel drive manual hubs, 7.3....
My first thought was to have the tires rebalanced and rotated to see if it is tire noise? I am hearing damage on top of the noise from the 7.3, hard to be sure!
View 11 Replies
My 99 F250 has just recently started making a "rattling" noise. The noise sounds like its coming from the front left wheel area. The noise is constant while driving down the road, its NOT created by bumps or anything, its a constant noise while moving.
View 3 Replies
2004 F-250 FX4 SB 5.4 V8 140k
Issue: rattling/clicking noise from passenger front wheel area at speeds lower than 15MPH, made worse under light braking and/or turns to the right.
Clicking sound is speed dependant.
Spindle? Hub? Balljoint? Sway joint? Rotor Issue?
View 14 Replies
2001 f350 4x4 dually 7.3 powerstroke, I recently replaced the hub assembly, stub shaft and seal, u joint, ball joints on the front drivers side and now periodically the truck makes a grinding growling vibration coming from front drivers side and stops after hitting a bump...
View 3 Replies
I have a 2003 F-250 6.0L 2WD and I recently noticed a rattling thumping noise under the front end on the passenger side. I noticed the rattle shortly after I got new tires, which are a hair bigger than the tires I had on it before. I thought it might be my new tires rubbing since they were bigger but then I noticed the rattle when I had my wheel straight and also when not moving at all. I've been driving it for a couple of weeks now with this rattle and I've been able to determine that it rattles most when I am going downhill and turning to the left putting more of the weight of the truck on the front right suspension components.
After reading several threads my first attempt to find the problem lead me to the discovery of a worn sway bar bushing. I thought this was for sure the problem and replaced both bushings and end links. But the rattle didn't go away. Then I thought maybe it was a bad wheel bearing so I replaced the wheel bearings in both front wheels. Still no change. Lastly, I happened to find a loose ABS line in the front right wheel well that was no longer secured and was banging against plastic. I secured that and still no change. All the bushings seem to be in good shape so I am considering taking it to a mechanic since I don't want to just replace everything hoping that it solves the problem piece by piece.
View 12 Replies
I got a 2001 f350 got a noise in my left front wheel i know its not the wheel bearings, it only makes the noice when the locking hub is unlocked i did jack the the truck up and spun the wheel got a faint grinding noises form what seems like the locking hub so my question is bad locking hub or needle bearing holding the axle shaft??
View 3 Replies
I bought a 2000 F250 V10 Super Cab. Oddly after a few weeks it has grown on me. There has been a clunking noise out of the right front over bumps. I traced it to a bad axle bearing. The u joint moves up and down about a 1/2 inch. Besides pulling the hub/bearing assembly out and removing the axle are there any surprises getting the old bearing out?
View 1 Replies
I have a really loud whining kind of noise found that its the wheel seal rubbing on the inner part of the wheel bearing. I was just curious if its safe to drive with the spindle removed from the axle?
View 5 Replies
On the F250 trucks, if I changed the mounting frame under the seat, will the passenger side seat fit on the drivers side? Basically, can I turn a passenger seat into a drivers seat?
View 4 Replies
99 F-250 Ext cab 4x4 7.3 285,000 miles.
I got home today opened my door and got snaked in the face with the smell of brakes. I got out of the truck then I heard the drivers side rear brakes popping as they are cooling down. I reached down to touched the wheel and it's crazy hot. Opened the garage and went to retrieve the infared thermometer. The rotor/caliper was 350 degrees, hub was 150 degrees, axle tube was 90 degrees.
I took the wheel off and inspected stuff. The rotors do have some heat spots, the caliper visibly looks okay but not 100%. The pads look like even wear. I am guessing that the caliper either is hanging up or I have a wheel bearing going? The passenger side was like 80 degrees on everything. There is a slight shimmy while driving which to me feels to me like the beginning of warped rotors. I don't hear anything to me that screams wheel bearing noise wise.Brakes or bearings?
View 7 Replies
