Ford Super Duty (1999-2016) :: 2000 V10 - Truck Started Smoking Under The Hood At The Top Of Drive
May 3, 2014
2000 Excursion 4x4 v10 auto. Pulling the boat last weekend up the driveway from the lake and the truck started smoking under the hood at the top of the drive. Jump out and saw a fire under the pass floorboard. Go the hose and put it out in 30 sec. Thought i blew a trans line and it sprayed on the cat. Took it to the shop and he said lines are good it's not leaking. He said it is possible that the trans over heated and built up pressure and blew it out past the front seal.? What happened or how to prevent it from happening again?
View 13 Replies
Advertisement
All week the truck was acting like the clutch was slight depressed when first taking off and then today i was driving and the underside of truck started smoking like crazy and slowly lost all the gears could put it in any gear and nothing just was acting like it was being revved. does this mean clutch is bad?
View 10 Replies
So I went to start the truck this morning around 8:00 and it was 7 degrees outside, when the truck started the oil light came on and oil gauge was on low? So I turned it off right away. few hours later I tried it again and still nothing I thought maybe the oil was frozen. After I started the truck the oil was higher on the dipstick so I am assuming the oil pump is functional. What could be causing this? Could it be the the gauge is not working? The truck is a 2000 F-350 V-8 5.4 gas. I'm hoping it is something simple I am suppose to work this afternoon
View 14 Replies
2007 f350. About 2 weeks ago my truck started smoking really bad, and I took it in to have it diagnosed. It was 4 injectors that were bad, so I had them replace all 8 and also install a bullet proof oil cooler. From the moment I got the truck back, it did not seem to idle as well as it used to, and over the next week, it began to blow a good amount of white smoke and run very rough.
But the weird thing is when I took it back to the shop to have it diagnosed, the minute I pulled into their driveway, it ran perfect, and they were unable to pull up anything. The next morning, I started my truck for work and as I drove down the street, the truck ran extremely rough, and seemed to be running in 2 cylinders. I shut the truck down, restarted it and it ran a little better, as I limped it back to the shop.
View 6 Replies
Question, my truck started to have a miss under normal acceleration, when I really get on it, it clears up? I also noticed a bad sulfer smell at idle. Im thinking the cat is possibly plugged? Truck had 172000ish on it, and the cat is original. I did do a big tune up this past fall, new plugs, coil packs, air and fuel filter. Should I put a new cat on it? And a new oxygen sensor?
View 9 Replies
Does it need a diesel fuel injector?
View 2 Replies
I've got 330 miles on my new 2013 F550. I'm getting ready to take a 2200 mile trip. So I'm giving the truck a quick once over I pop the hood and to my amazement the inter hood has started separating from the outer shell. I would think its going to vibrate now.
View 12 Replies
I have searched and tried everything that was suggested to open the hood on my 2000 and nothing works. When looking form the front you can see the hood release operate, but nothing happens. What part of the release do I need to operate to get the hood to open?
View 5 Replies
2005 F-350 6L diesel .... Put new batteries in it a week ago.
Been running good then the radio quit a couple of times. It came back on after truck was restarted. This morning I go to town and the battery light comes on. I stopped and started about 5 times and on the 6th it wouldn't start.
I got a boost and started home it , started to try and quit when I was almost home. Was so dead the power windows wouldn't even work. Have it on the battery charger now and it starts right up but the battery light is still on and the ABS light is on.
View 6 Replies
My 2002 7.3 will go dead when driving then not start up until after it has sat for a good hour. Then only run for about 10 minutes before dying again. The truck will stay running if left in park idling. It only stalls when it is driving.
I replaced the Camshaft Position Sensor and Alternator with Genuine Motorcraft parts. My next assumption is the ICP Sensor? Maybe. I do have a kill switch on the truck that I thought might be loose--but I'm not sure.
View 3 Replies
I replaced a rear rusted brake line a couple of years ago. It rusted where the line met the bracket. I'd never done this before but bought a flare (flaring?) tool and fixed it.
This week the longer line that runs down the length of the truck started leaking. It looks like the line was once held in place by a small bracket just in front of the rear wheel but it wasn't in that bracket anymore. I guess it rubbed against the metal and water/sand rusted it out.
A local garage said they'd need to drop the fuel tank and estimated that it would be several hours (and hundreds of dollars) to do the job. It looks like I might be able to cut the old one out and then fish the new line up through there and replace it.
Also, what is the diameter of the line? It is a 2004 F350. I can certainly cut it out first and then take a piece of it to the local auto parts place to get the replacement line.
View 9 Replies
So a few months ago I would occasionally hear what appeared to be a slight squealing noise from a pulley when I started my truck. It was very intermittent, so I didn't think much of it.
After a few weeks, I realized I was only hearing it on colder mornings - it would also go away rather quickly. I bought a mechanic's stethoscope, and figured I'd get to it on a slow day.
Today, I finally broke out the scope and tried to figure out the source. Didn't really find any pulleys making noise, and I did notice that when I shut the truck off, it squeaks for a second or two as it comes to a complete stop.
My dream of finding a bad pulley or perhaps a power steering pump was crushed. I had hoped to do a little Easter wrenching and put this noise to rest. So, I did what any good mechanic would do - I Googled the issue.
I'm reading that it could be the belt. Certainly wouldn't bother me too much as that is an easy fix. The belt isn't too old - about 4 years and 20 - 30K on it.
I took a few pics of the belt and can take a video of start/stop ....
View 7 Replies
I had a can of fuel at home that had been siting around a while but I put it in my 02 F350 with the 7.3. hind site being 20/20 I shouldn't have done that. The truck only made it about 2 miles then started chugging and eventually quit. So I pulled the truck home and this is what I have done so far. I assumed that I had bad fuel so I started with a new fuel filter. I did notice that the fuel in the bowl was a milky white color. Not sure what that means. But the new filter did not work as the truck will not start. So after reading some other posts I decided to drop the fuel tank and clean everything.
I did that including cleaning out the 2 screens in the fuel pick up. After re installing the tank I put new clean fuel in the tank and primed the truck. But before starting it I drained the first amount of fuel out of the filter bowl just to make sure I got all of the bad fuel out of the lines. So after doing this I put a new filter in and primed the motor again. I appear to be getting good fuel pressure and the fuel looks very clean now at the bowl. But the truck does not even attempt to start. It turns over just fine but will not start. Some advice I can get before I have it towed to a shop. Also, the truck currently has 305,000 on it and has run great up till now.
View 5 Replies
2002 5.4 super duty. My truck had started to ping, and knock worse over time. I did some research on this site, and I decided to remove my K&N air filter. Replace it with a traditional paper filter. Then I cleaned my mass air flow sensor. The results were great, no more knock and ping.I will check the MPG next to see if I get any improvements.
View 1 Replies
I have an 03 with a 6.0 diesel, going down the road and started losing power and then died. Won't start, and I don't have a scan gauge. Several sources said ipr valve, and from videos on youtube I thought may be a good place to start. I bought a socket and pulled the valve, to check the screen. There is no screen whatsoever on the ipr. The oils clean, as I had changed it about 200 miles ago, and I ran a magnet in the hole looking for a screen, couldn't find anything so I used my fluid pump in the hole. No trash, screen or anything. Do some ipr valves not have screens? What would be my next step??
View 2 Replies
I'm getting a really choppy low RPM drive. If I'm above 2-2.5k rpm it runs okay but as soon as it drops under 2.5k it starts to run very choppy and loses power and Boggs in and out of power regardless of how much throttle input I give it. I had a tune up done last year and a recent oil change...
View 1 Replies
Here's what I have 2000 F350 XLT 105000 miles and a 4R100 tranny, was coming home from work no issues, stopped at my mailbox to retrieve mail.
when applying brake, it lunged forward a bit and stalled, I started back up put in drive, stalled again. started back up put in reverse, no issues.
I put in neutral revved it somewhat and it moved forward enough to start the roll down the small slope at my drive, I then started in neutral again as was rolling and then put into drive and drove 1/2 mile down my lane to house. backed up in my parking spot, no problems then shifted to drive and stalled.
Today I dropped the pan and checked the filter as I have read that sometimes they will fall out and cause same symptoms, filter was where it was supposed to be, no easy cure here.
View 1 Replies
I recently purchased a 00 F250 psd 4x4. Other than doing all of the fixes it needs to make it ride better I have been questioning the trucks "get up and go" and the EXTREMELY sensitive skinny pedal. Truck seems to pull very hard and puts out some black smoke under hard throttle but nothing like the really tuned trucks I have seen. But the skinny is so sensitive its hard to drive under 40mph in 3rd and once it gets up to 55 or so its real sharp getting on and off the throttle. Trans shifts great, TC locks and unlocks, truck runs awesome IMO but just a bit harsh. Is there a way to find out if it was tuned prior to me buying it other than inspecting for a chip, or is this the way they are and I just have to get used to it more...?
View 9 Replies
2001 F450/6.8 gasser. Auto trans. This strange thing just appeared from nowhere. Start the truck, put it gear. As soon as the truck starts to roll, the chime begins to sound. If I continue on, it'll beep 80 or 90 times before stopping. As soon as brakes are applied and the wheels stop turning, chime disappears. Happens in forward or reverse. No lights appear in the cluster. A check with an Actron scanner shows no codes or MIL. Seat belts are buckled.
View 4 Replies
I have a 2000 f350 xlt and it has been very good until now. I can be driving normal and stop and park, when I get in and try and start it , it acts like the neutral safety switch is not working. the key turns and all my dash lights work, radio works, everything but the starter. I have to put it into neutral to get it to start. then after I stop again, it works fine. I don't get the problem all the time and I can't find a neutral safety switch.
View 8 Replies
I just bought a 2000 F250 SD, 4x4, 5.4, Quad Cab. I drove it off the lot, stopped to put air in the tires, jumped back in and it wouldn't crank. All of the dash lights worked fine. Tried jumping at the starter solenoid and got nothing. Got under the truck and jumped it off the starter, vroom, fired right up. Replaced the starter solenoid and had no issues for about 2 hours. Then it did it again. This time it wouldn't start at all. I towed it back to the dealer and they had it for 3 weeks.
Then yesterday I called and they said it was done. Picked it up, drove to the barber shop, got my hair cut, came back out and it did the same thing AGAIN. After jacking around with the shifter and turning the wheel back and forth 100 times it started. The key is kind of hard to turn sometimes in the ignition, so I'm thinking that the ignition cylinder needs to be lubed real good, but that shouldn't stop it from cranking the motor over, right? I was going to swap out the ignition switch, but I don't know if that will do any good either.
View 3 Replies
