My daughter has this truck and I was driving it the other day I noticed it misfiring when the trans shifts down under a slight pull and/or going up hills. It looses power and speed when this happens but if you back off, it smooths out when it shifts into overdrive. I haven't had it to a mechanic to check any codes yet.
View 3 RepliesI have 99 f350 v10 4x4 and trans shifts great under light rpms but 2-3 shifts very hard. At wide open from about 35 mph it will shift down and take off like a bullet but wont shift until I lift my foot and then it bangs hard from 2-3. All other gears are smooth. I did some searching and have found some threads saying it could be an accumulator spring that is broken? Truck has 115,000 miles on it. love the truck but want to fix this before it does some damage.
View 1 RepliesI recently purchased a 04 f250 with the 6.0l powerstroke. I drove it for about 3 weeks now, Ive put my trailer behind it with small loads and just today tried to use the tow/haul button. When you go to pull out the tranny never shifts from first gear?? Its pulls and runs fine until you push the buttan and no shifting........
View 6 RepliesWhenever I manually pull my gear selector into first gear it blows one of the 10a fuses (not sure which number). I lose all gauges and accelerator pedal. It's about the fourth fuse from the right on the bottom row.
View 4 RepliesI have a 2000 f350. When idling uo can't really hear the miss. Driving at about 40-50 mph it will shack and shutter real bad. Hooked up spanner and had miss fire codes for cyl. 1,4,9. Changed out all 10 plugs, and boots. Also changed out the coil on all three cyl also. Still have the miss and shutter. Also changed out #9 injector ...
View 12 RepliesMy F350 idles fine but every 10-15 seconds it mis fires. When asking it to go up hill it sputters and seems to loose power. It runs fine until asked to work hard. Not really sure which direction to go in first.
View 9 RepliesI have a 2004 F250 Torqshift trans, 155,000 miles. It has had a slight hesitation when trans is engaged for about 4 years, not a problem the dealer has no fix they said.
Now today for the first time I had a tow haul light come on while driving on the freeway. It would not go into overdrive and the light keep blinking. Later in the day, I let it cool down and it drove fine to the store about 2 miles. When I got in to drive home it had tow haul light go blinking and check engine light came on this time.
I hooked up my code reader and it's giving codes: P0720, P0751 and P0766.
Should I take it to the Ford dealer, a Transmission shop or have a friend who worked at Ford Dealer do the Work? I see that some people have changed out the TFT sensor and corrected the problem. While the pan is down should I just have all the shift solenoid sensors changed?
And if I have to sift through one more "My O/D light is blinking."
I have a 2000 F350 7.3 4x4 SRW CC with several issues but right now I'd like to address the one plaguing my transmission. If I crank the truck and take off it will not shift out of first gear, well it might but it'll take a while, be at high rpms, and a hard shift, throwing the 1-2 shift error code. Now if I disable O/D with the button on the shifter and take off it shifts through all gears fine. I can drive it normally and if I hit the highway, when I'm up to speed I can enable O/D, it shifts into O/D and I can keep on trucking. When I stop I disable O/D and take off normally again. After about 10 minutes of driving and several start/stops even with O/D disabled it will eventually throw the 1-2 shift error code and give me a harder shift into 2nd and I guess enters its limp mode but is still drivable. This appears to be the only code dealing with the transmission.
Due to the fact that it shifts fine with O/D disabled, doesn't skip any gears, and I can manually shift it through 1-2-D I'm guessing it's not the mechanical diode I've heard so much about but an electrical issue. Before I bought this truck it had been abused, at one point the front driveshaft came loose and ripped the wiring harness going to the TRS in half. They soldered it back together but it still looks a little rough. I figure this is a good place to start. What readings I should get at the TRS? Sensor side and plug side. I have the AE enhanced ford bundle and a good DVM. If the TRS can't cause an issue like this where do I go from here, shift solenoid?
TLDR Version
2000 F350 7.3 4x4 SRW CC
Won't shift out of first with O/D enabled.
Shifts fine with O/D disabled.
Can manually shift through all gears.
Eventually throws 1-2 shift error code.
TRS/TRS Harness has been damaged in the past.
Appears to be an electrical issue with the transmission.
Can the TRS cause an issue like this?
How do I test the TRS/Harness?
If not the TRS what could it be, shift solenoid?
I drained the transmission fluid on my 2000 f250. I measured the fluid at about 6 quarts. I refilled with 6 quarts. I drove until the engine was hot and checked the fluid while running in park. Each time I check it I get a different reading on the dipstick. I wipe off the dipstick each time but sometimes I pull it out and it reads low. The next try it shows about 1/2 inch over full on the dipstick. Can't get two consistent readings. Is it harmful if it is a little over or under full?
View 4 RepliesI am in the process of replacing the front hub seals so my ESOF works again. I tested both front hubs with a mityvac and neither one of them holds any vacuum at all. All the lines are good, and the pump and solenoid seem to be working fine.
I have the driver's side apart and I have a couple of questions.
What's a good source for the vacuum seal? I've checked rockauto, riff raff, and diesel o-rings. Diesel o-rings has it, but the description says it's only for 2003+ Excursions so I didn't order it.
There is no yellow o-ring anywhere on the hub. I assume that someone forgot to put this o-ring back in and this is why I don't have ESOF? I guess what I really want to know is that there isn't some 2000-specific thing where there's no o-ring, right?
After I got the hub off, I spun it around on my workbench and it doesn't sound good at all. It makes a slight metallic grinding noise about 1/2 way around. I assume this isn't normal? AFAIK these are all original parts - but the missing o-ring means to me that someone already had it apart.
There was a lot of water intrusion and rusty colored grease but nothing was dry, the needle bearings were intact and the shaft isn't scored at all where the bearing rides. I'm hoping new seals and good cleaning and it should be good as new. And then it's off to the next side.
I purchased a 2000 F250 7.3 4x4 (auto transmission) about 8 months ago. I've noticed recently that when I accelerate there is a slight hesitation like there is slack in the drive line. This does not happen when the truck is moving and I accelerate. There is not audible clunk and the hesitation is not in the motor.
I checked the u-joints and they all feel tight. There is a little slack in transfer case that allows me to turn the drive line slightly back and forth. Is this normal? Should I be planning on a transmission or transfer case rebuild soon?
Update: I was researching the leaf spring isolator pads (mine are warn out or missing) and it sounds like these can cause something similar to what I am experiencing. I am planning on pulling a 28' travel trailer from Colorado to Wisconsin next month and would like to avoid any issues if possible...... Obviously, I know ....
On a 2000 F-350 with 5.4 engine, where does the vacuum line enter the cab? I got a truck in with no vacuum signal to the heat controls, and it has a slight miss at idle. Both of these are signs of a vacuum leak, but i can not find the line going into the cab.
View 5 RepliesHad an issue pop up today while driving. Heard a bit of a wierd soft grind sound under dash while letting off the brake at a light to go. Upon applying brake again it was ok (slowing early to a red). Then lifted foot off and applied again. It was then the pedal was hard (ish) to push but was still safely slowing the eX.
Then as I slowed more, the pedal went a bit further down and I felt the ABS pulse through the pedal. Very light braking by this point. There was also a little bit of a pull to the right. Pulled over. No leaks, visual inspection done.
Held my foot firmly on brake. It didn't move to floor, so I know there wasn't a leak in hose or anything dangerous.
Drove cautiously to my destination, repeating same scenario until I came to the side streets. Having lots of snow here I was able to push pretty hard and have the pedel become hard to push, while still locking the brakes up into a skid. I did, however, notice the rears would lock, NO ABS feedback.
No ABS warning light on dash.
I could drive pretty quick, hit the brakes hard and all was well until 15mph or so, then the pulsing would start. Pedal got hard (er) to push. Quick stops and really slow slow down stops. All with a little pull still to the right. Pedal was always harder to push back down the second brake application (one after the other, not the next stop light). Possible ABS Sensor issue?
Truck pulls to the left while braking, pretty bad. So, pulled the front right wheel off thinking the pins are stuck again as last year. Bottom pin was fine, top pin pretty gummed up but not froze so I cleaned it up good, used thin layer of the good stuff, put back together and test drove........same thing. Pulls left upon braking just as bad as before. Caliper pistons seemed fine, didn't take much to compress them either.
View 8 RepliesHave 2001 F-250 7.3 PSD, automatic, ESOF (had to replace the original hubs with Warns)have kept up the maintenance,oil, grease, ATF fluid & filter, truck has been virtually trouble free. About 2 weeks ago I decided to go across an area of the lawn, as I was going (in 2 wheel drive)I felt the tires spin a little so I stopped got out and locked the hubs, got back in truck turned t-case to 4 high. had to rock the truck out of a damp area but nothing really.
So I got back to where I came in at (in reverse about 100') stopped put it back in 2 wheel drive, tried to go forward, very difficult, sluggish, got back in driveway had to back the truck in, will not go forward at all now. Checked all fuses, rapped the the t-case motor, no codes. So I thought I'd move the ruck, have a winch that will pull it out by the barn, I could not even move the truck forward by pulling it with a winch. As I said have never had any problems with truck. Transmission fluid is good, clean no burnt smell.
I have a 2004 super duty diesel 6 with electrical trouble dash lights stopped working put in new fusses where needed still no dash lights but now truck starts and runs ok but will not shut off unless I pull ignition.
View 2 RepliesI recently took delivery of a new 2012 F250. It was a cab chassis, we had a utility bed and lift gate installed from the upfitter along with heavy rear springs. From day one the truck would pull left when the brakes were applied. The brake pedal also feels mushy, not firm. It will firm up when I pump it. I could also smell burning around the left front of the truck when I would get out of the cab. Hot brake smell. Took it to the dealer with only 400 miles on it and they replaced the front pads and turned the rotors, and gave it back. In relatively few miles the problem was right back again.
Took it back to the same dealer last week with 1200 miles on it now. This time they say they replaced the rotors. I went and picked it up it this morning. Within 5 miles drive of the dealership I can tell the brakes are still bad. Now, it will kind of do a "head fake" when the brakes are applied, pulling slightly left or right, before deciding which way it wants to pull. It will pull right or left now during firm braking. And the brakes were stinking by the time I had it back to them. I turned around and took it right back to them again. Brand new F250?
I'm looking at purchasing a 2003 F-350 from a Ford Dealer, Drove the Vehicle last night and the Gear shiftier was very tight and hard to pull down. Is this a real concern? The Sales guys said its better to be stiff rather than sloppy. But they will say anything, right. The vehicle is a deal and so I'm looking to find out why.
View 1 RepliesI just bought a 99 F250 Super Duty with the V10. When I bought it, I knew it had 2 misfiring cylinders (4 and 10) because it was throwing P0304 and P0310 (only 2 codes), but wasn't concerned as I've had to take care of my wife's Escape with it's misfiring cylinders. I replaced the 2 coils and replaced the plugs with Motorcraft plugs from O'Reilly's, cleared the codes and she ran fine for a couple of days. Now I'm getting an intermittent misfire, it's only occasionally throwing a pending code of P0300 which is "Multiple Random Misfire".
I'm fairly certain it's an issue on the electrical side because if it were an issue with the injector or injectors it would be constant regardless of RPM... right? As it is now, it basically does it between 55-65 while in overdrive trying to pull a hill or slightly accelerate. Once it's shifted out and the RPMs go up to 2k+ it runs like a champ... and it kills my fuel economy. The way it's behaving is just like when a coil is bad, but it's saying it's not identifying a specific cylinder (saying it's multiple) and it doesn't always do it (about 60% of the time).
I checked the MAF and it's very clean (looks almost new), checked the vacuum lines (those I found without a manual) and couldn't find any leaks and when I changed the plugs all the plug wells were dry.
SO this truck came into the shop yesterday with a really bad misfire. pulled the codes and got a misfire codes for cylinders 1-6 and also p1450 (unable to bleed fuel tank vacuum) and p068a (pcm/ecm power relay de-energized too early) i found a TSB related to the issue, TSB 10-25-7 i did as the tsb told me to do and pulled valve covers to check out the rocker shaft rollers and inspect for any signs of surface deformation or fatigue. they were fine on both sides.: ive got spark in all cylinders. fuel pressure was right around 55-60 the gauge was fluctuating pretty good. checked for bad fuel or water in fuel ect. fuel seems to be good. pulled O2s incase of plugged cats still ran like crap.
View 13 Replies2012 F-250 6.2 gas 4X4 SC/SB: when I run WOT, or near that, from a slow speed, I hear a short "hiss" between the 1-2, 2-3, and i think 3-4 shifts. I can also feel that the engine eases up quite a bit during the shift, and it is kind of a slow, soft shift. It has about 2,000 miles on it. I bought it in March 2013 as a leftover (great price!). The door sticker says it was manufactured in 4/2012, so it sat on the lot for quite a while before i bought it. But i don't remember it doing this when it was newer (~500 miles).
With the lite weight of this configuration (it is an XL so it isn't even carrying around 4 speakers ha ha), and me rarely carrying a very heavy load (yet) or towing anything, I rarely have to step on it very much in normal driving... it hardly ever gets above 2,500 rpm unless I am just running it faster for fun.
The hiss and slow shift happen at any transmission temperature. Of course, it never has been above the left side of the "gear" pic on the temp gauge, where it always is after full warm-up. Well, I'm hoping it is just shifting soft like this because it has "learned" my lite-foot driving style (even when I'm in a hurry of course the engine rarely has to work very hard).