All of the sudden ignition stays on aux when the key is removed. Starts and runs fine with key , also shuts off with key. However when key is removed all aux functions still work ie touchscreen reciever will not turn off, and door chime continues to ding. 2000 excursion 4x4
View 1 RepliesI'd like to be able to have the key in the ignition and still have the door open without the incessant dinging of the key alert. Is there any way of shutting it off without having to cut wires, etc.?
View 1 RepliesI bought my 2000 F-250 CCSB a while ago and it came with 2 keys - one for the ignition, and one for the doors/tailgate - may not seem like a big deal, but it annoys me to no end.
From my understanding, the truck had previously been stolen and had the driver's side lock punched, and then something happened to the ignition lock to where it had to be replaced - hence the different key. I finally got around to replacing all the locks so that I'd only have one key. I started with the doors, then moved to the ignition (which I thought would be the easy part). I've replaced several cylinders before and I know it should be simple, but for the life of me I can't get the cylinder out!
I push the detent, turn the key to run, wiggle and pull.... nothing. I can feel the detent push in, and the cylinder will move a little, but it won't come out. I'm not sure if this is something that just happens sometimes and there's a fix for it, or if I'm in a unique circumstance and my column was somehow damaged during the theft and that's what's causing it.
I have a 2000 F-350,7.3, 6 speed. Just the other day I made a turn and my passenger got her feet wet. It had been raining and I also had the ac on. A couple of days later the same thing happened, but it had not rained, just the ac on. What is causing this. I do see condensate discharging under the truck.
View 7 RepliesI have a 2000 F250 SD with the V10 engine. The problem that I am having with it as of late is that whenever I perform a full turn I hear some clunking coming from the front end. The clunking is similar to that heard from cars that use CV joints FWD but of course it sound more "manly"
Anyways, my truck has the full axle on front so I suppose it could be either the u-joint at the hub or the hub itself. I would like some pointers so I can acquire the required parts.
But on my 2000 SD V10 the hubs are worn I just cant find which way to turn them to auto ?
I'm getting popping and such so I think I'm locked while turning.
Also.... IS there a way to check the COPS with a multimeter? I think I got a bad one.
2000 V10 F250 - daughter is using my truck and called to tell me the turn signals weren't working. She called me shortly after and said she adjusted the tilt and hazard lights came on and now she can't turn them off. I had her pull the hazard fuse to stop them. She then noticed the brake light weren't working. I don't know if the brake lights were because she pulled the fuse or she just noticed they weren't working.
A week or two ago, she said she parked the truck, turned it off and took the keys. When she came back out, the truck had rolled across the street. Periodically, over the years, I would go to start the truck and nothing happened. I would shift the gear selector in and out of drive. Then the truck started.
Finally, since I've owned the truck, the when I activated the left turn signal, the selector frequently wouldn't stay "locked" till I turned. So, are these related? Do I have multiple issues going on in the steering column. Where to start looking when she gets the truck home?
First off my trucks a 2000 v10 f250 with four-wheel drive and 2 wheel abs with about 230000 miles on it.
I Recently replaced my unit bearing on my drivers side because I thought it was the cause of a grinding that only happens on hard left turns but I wasnt the cause it was going bad causing play in the half shaft. I didnt seem to notice and wear on the shaft from bad needle bearings but I have to take it all apart again to be sure. Was just wondering what else could be the cause of this noise. I plan to pull the axel shaft and change all the seals.
2005 Ford F250 5.4 ... Having problems with ignition switch or bus bar in that circuit being bad?
View 3 RepliesWhere I should start looking to solve this thing. Got in my truck to drive home at the end of the day today and noticed the radio was on. Started it up, seemed normal. Shortly after the thing started incessantly *BONG-BONG-BONG*-ing at me. Drove home, turned it off. Started pulling fuses, find the culprit, silence it.
It's no longer constantly on and it seems to have flattened out and is only doing it now when the key is in the off position, otherwise silent when running or in the normal on position. I know it's not this contact (the one in the tumbler above the release pin) that's making the problem happen, as mine is disconnected. It's definitely something in the ignition tumbler or similar that's making at least a couple of the circuits think the key is in when it shouldn't be.
I don't even have the factory service manual for this thing yet with all the electrical diagrams to figure it out. Truck is a 2001 F250 PSD Lariat CC, for what it's worth.
2005 F250 superduty 5.4l crewcab. When I shut the truck off and remove the keys from ignition, the chime keeps going off like the keys are still in the ignition until I turn the ignition back to the off position again.(about 1/8 of an inch.)
View 4 RepliesI have a 09 F350 Lariat SuperCrew SRW 4x4, Last night the ignition key would not turn at all. Tried wiggling the steering wheel, (noticed it wasn't locked), wiggled the shift lever (auto trans). After about an hour of "beatn and jiggling, it just started working!?? What caused this, neither does my dealers service dept. It's working fine now.
View 11 RepliesHow do you get the door chime to go away when the key is still in the ignition?
Also, how do stop the driver seat from moving every time the key is removed?
So I have a 99 F250SD, earlier this year my wipers started going on by themselves, switch didn't seem to effect them, wouldn't turn off with the switch but would with the ignition off. Then they stopped working all together along with the washer. Checked fuses and relays, put a new switch in and still no dice. When I move the switch the wiper/washer relays do not click at all.
I've tried tracing the wires but haven't been able to find any issues there. The gem is as clean and new looking as one made yesterday. Is there a pinout test I can run on the plug into the motor? or which color wires coming out of the fuse box to check? I'd really like to get this fixed so I can drive my truck this winter.
I have a 2002 F350 V10 and one night I turned the headlights on and when the ignition switch was turned to the off position the lights would go off. When the ignition switch is turned off the lights come back on. I changed the ignition switch but the problem still exists.
View 3 RepliesOkay, I've done a few topic searches and see some variations on this, but not this specific scenario. 2001 F-250 (5.4L, 4x4, auto). My daughter's truck and I wasn't home so this is the best info I have as relayed by her.
She turned the key off, the engine shut off, but all the "electrics" stayed on -- radio and a/c fan to be specific. She said that morning the truck had a dead battery so she got a jump start, leading one to suspect that the electrics stayed on the previous night as well. (?)
I had her disconnect the battery and let it sit until I got home. Of course, when I got home and reconnected the battery, everything works normally as it should. And has worked normally for a few days.
So.. any words of wisdom out there while we wait for "the next" occurrence?
Since yesterday, every time I turn the key off and remove it from the ignition the truck just keeps running. Engine, radio, according and everything just like the key was still there. When I press the unlock button it shuts everything down. It is a 2014 F250 with 4500 miles on it. I don't know if I did something or what but I am confused.
View 8 Replies1999 5.4L F250 ... When I turn my ignition all my lights come on and I have power to dash and etc, battery is strong, but when I turn the key I get nothing even when I do the shifter trick for the slip we get on most fords nothing took ignition lock cylinder out and blasted it with electronic connection cleaner, when key is turn i loose all power to everything and there is no "click" or i gage from anything under the hood or the starter rally confused!
View 13 RepliesI've noticed that when I insert the key in my 2013 F250 I hear a humming noise, if I pull the key out it goes away. What is this noise? It seems to do it as long as the key is in, but is quiet enough that you can only hear it when there isn't a lot of back round noise.
View 14 RepliesI have a 2004 super duty diesel 6 with electrical trouble dash lights stopped working put in new fusses where needed still no dash lights but now truck starts and runs ok but will not shut off unless I pull ignition.
View 2 RepliesUpgrading ignition coils on 5.4's? Looking to upgrade mine and only came across a few and the reviews are mixed. I am primarily looking to smooth out the idle and gain some minimal power and maybe get a flicker of a gain in mpg.
View 3 Replies