Ford Super Duty (1999-2016) :: 2000 - Getting Code PO303 Due To Deposit?
Mar 22, 2017
I was getting codes on 3,6,8 cylinders. I found a broken wire at the coil on 3 and the bolt was broken that secures the coil. No plugs were blown out. I replaced coils and plugs on those cylinders and rewired at #3. I also checked and cleaned the injectors. The 6 and 8 codes are gone but still getting a code on #3.The coils were out of wrecking yard and I suppose it could be a faulty wiring job. Could I take a well-insulated screwdriver and check for spark from the coil at the spring? The plug was heavily deposited as it had not been firing. Could deposits be causing other issues with raw fuel having been dumped in the cylinder?
View 10 Replies
Advertisement
I plan to be buying a 2000 F250 V10 in a couple of hours.
I had my boss run by and take a picture of the door tag so I could determine the axle code. What he sent me was this:
Other than giving me the knowledge of how bad of a photographer he is, it doesn't tell me much else. The axle code area is blank, what gives? Am I just going to have to crawl under the truck when I get there after work?
View 14 Replies
OD light flashes on my 2000 F450 7.3 but still runs and drives shifts fine. If i turn o/d off before i get going then it won't throw the code and start flashing at all. I am going to check the harness again to see if there are any bad wires. If not is it usually a bad solenoid pack i can just swap it out and fix the problem? I have to replace the pan soon so when I do if I need to replace the pack I'd like to do it then.
View 4 Replies
I have a 4r100 in my 2000 f250 7.3. I am getting a P1746-EPC Solenoid, open circuit. Does this mean this particular solenoid in the solenoid body has failed and should i replace the solenoid body?
View 3 Replies
i'm looking to upgrade my mirrors. A friend told me to get the 08+ mirrors but I can't find anywhere online that says they will work. I'm hopefully going to be purchasing on Amazon but not sure which ones to get. When I pull up the 08+ they say "Fits Ford 2008-2015 2008 2009 2010 2011 2012 2013 2014 2015 F250 F350 F450 F550 Super Duty"
Ive got the 2000 F250 V10
View 14 Replies
Okay I bought this 2005 Excursion with a V-10 in it. Got it home and the CEL came on. PO303, @ first 1000 rev. Okay so I changed all the spark plugs, swapped the number 1 and number 3 coils, same code, and as a last resort changed the injector also. Ran it 65 miles bam lights back on. Same code I'm at a lost of what to do. What are my next steps to take to fix this?
View 14 Replies
What a Brake Code - 4 means for a 1999 Super Duty on the door ID tag?
View 4 Replies
I just purchased a f350 super duty 07 4 dr long bed with the 6.0 liter trying to find the 5 digit code so i can reset key pad on door.
View 2 Replies
Replaced my old sagging leaf springs with new X code springs. Had an almost impossible time centering the axle even with adjustable center link. Even with it totally maxed out it is just barely centered. Now I have a terrible squeak coming from springs. Is this because of the side loading of springs? Is there any fix for it? Not only do they squeak but the drivers side now sags almost an inch even with brand new springs. 2002 F350. Super annoying and irritating
View 1 Replies
I have been trying to find a new sensor after my truck popped a P2285 code. I can't find ICP sensor at any auto parts store. I found this but it was labeled as a fuel pressure sensor on RockAuto: More Information for Standard Motor Products ICP103... Is this the same thing?
View 2 Replies
I have a 00 F250 7.3 4x4 and I am looking to get better mileage out of it since it is now a dedicated work truck for towing. The two options I have in mind I think will work, but just wanted some clarification and if one is even possible.
First I will be taking the lift off and dropping back down to 33 inch tires or so. This should give me a little, but if not it should be easier on the truck for towing.
And this truck mostly see's highway miles, so I was thinking about disengaging the 4wd. I heard 4wd trucks get worse mileage, so this is the one I didn't even know if it was possible. not digging in to the computer and injectors quite yet.
View 7 Replies
Have a 2000 F-250 V-10 4x4 with 335,000 miles on the clock. Has started hesitating at 40-45. You can't really notice it at idle. Drove it around at lower speeds and just a miss here and there. Take it up to 40-45 and it's quite bad. Hasn't thrown any codes. Hooked it up to the scanner to get no additional info. My gut says coil packs but am kinda confused that I haven't gotten a misfire code yet. What to check?
View 6 Replies
A vibration has just begun on my 00 f250 power stroke it's in the left front and happens when I hit a bump I changed out the wheel bearing assembly and I switched locking hubs with another truck all with no success don't know what else it could be it does go away if I lock in the hubs so idk
View 2 Replies
Code was showing for the knock and climbed under the truck and checked to see if it was plugged in grabbed the wire and to my surprise the wire kept coming and so did a piece of the knock sensor, is this going to affect my truck badly?? worst case?? 97 f250 4.6 standard
View 4 Replies
2004 SD ext cab 5.4L Gas ! I have a mis-fire at low RPMs ! Autozone said it kicked out code P0316 Crank Position Sensor ( CPS ) but the CEL was not on ! So I replaced it and Still has the same problem. I checked the coil packs there good according to the autozone diagram "how to" ! I also pulled each wire 2 check the old shade tree way to see if I could tell that way. Now the CEL is on...
View 14 Replies
1999 F250 Super Duty 6.8 V10 4x4 157k miles
On Friday afternoon the ABS light on my dash came up, ran the codes on my SCT Livewire and came up with a "P0500 Vehicle Speed Sensor A"
What should I be going after? Rear speed sensor? Front ABS sensors? Transmission speed sensor?
Speedometer is functioning 90% of the time, twice in the last 48 hours it wouldn't then shift hard and I would pull off to reset.
I have looked over the search results and wondered if there is a way to test the sensor with my multi-meter? Seems quite a bit of people had flashing over-drive light's at the same time, which I do not.
View 6 Replies
99 F350 7.3l with 4R100 trans. About a month ago I took out a monster trans that had about 60k on it and it was burnt up. No warranty. ..customer bought another monster. After the install when going into 4th the torque converter would instantly lock making it feel as though the truck was falling on its face. Monster had me do some data logging and from the info I provided they determined it had a bad solenoid pack. They sent a new one out...when I went to install the new pack I noticed when I dropped the pan that the fluid was iridescent looking...a bolt for the valve body was in the bottom of the pan and lots of material stuck to the magnets....
Needless to say that trans only lasted about 2 weeks after putting the solenoid pack in. Fast forward to today..got trans number 3 from monster under warranty. After the install everything seemed good. About 30 mins into highway driving the od light starts flashing. ..subsequently the P0741 code. I did put 2 new wire pigtails on the front and rear speed sensors. The pigtails were a ford service part but they were a bit different in design. I am pretty sure the wires are correctly oriented..if not would this cause the issue. I really am leaning towards a bad solenoid pack again. My buddy thinks the TC isn't seated properly....where do I start? Also has an edge programmer on it..but it's been on the same map all this time
View 10 Replies
My truck threw a check engine yesterday, P1151 and P1152. What could be the problem? 04 f350 with 5.4 with 142,xxx on her
View 14 Replies
I just ordered '00 F250 SC 4x4 SWB XLT with the factory standard manual hubs. The hubs show up on the vehicle order confirmation as code "21M MAN LOCKING HUB". I can't find this code in the ordering guides anywhere but kbb.com shows this code as "Manual hubs delete. Required with 213 shift-on-the-fly". I want the manual hubs. I think ##### is incorrect. For my piece of mind, could someone who has also ordered the factory standard manual hubs verify that the code is indeed 21M. And for those who ordered shift-on-the-fly, could you verify that 21M does NOT show up on your order confirmation...
View 8 Replies
Ok says injector pressure sensor low first guess was the upgrade to the blue spring. Did that code clear for a day then comes back on looking at the hfcm but kinda unsure? Came on after we got the real cold snap and i had to buy a block heater I don't see one on here i also added diesel 911 to the tank this is a 05 f250 w 6.0l....
View 2 Replies
So I'm not sure if I bought a lemon, but i picked up a F-350 6.4 Turbo Diesel two days ago and the check engine light came on yesterday. It's giving me a P0088 Code as well as the P0088pd. It's got 131,000 miles on it so no warranty will cover me.
I'm tracking the TSB put out telling the techs to replace the HPFP, but they mention a loss of power. I've only had the truck for two days, but I've driven them for work before and I can't detect any loss of power. Besides the code, everything seems to be running fine.
What can I can try out before running out and changing the HPFP? I'd rather not cut so deep into my savings if I don't have to.
View 6 Replies
