I have a 2000 f350. When idling uo can't really hear the miss. Driving at about 40-50 mph it will shack and shutter real bad. Hooked up spanner and had miss fire codes for cyl. 1,4,9. Changed out all 10 plugs, and boots. Also changed out the coil on all three cyl also. Still have the miss and shutter. Also changed out #9 injector ...
View 12 RepliesWhile driving into town during a recent snowstorm, my truck started to misfire quite badly. The check engine light started to flash and then remained on as I went to the auto parts store. The code indicated cylinder two misfire. I don't a few things of dry gas in the tank and let it run for a few minutes which seem to solve the problem.
Since then, however,every time the engine gets even a little bit wet it starts to bark again. It usually lasts a few minutes then goes back to normal. Typically, I would have replace the plug wires. When I lifted the hood of my truck I realize I knew nothing about it.
I have been having some inconsistency with my transmission in my 2005 F350. I bought it used 2 months ago and have had the low/tow overdrive light blinking. a month ago I removed the pan and changed the filter in the transmission. I had a friend run the diagnostic test and found transmission solenoid code as well as both cat. converters as well as my Number 8 cylinder misfiring... I pulled the transmission pan and filter to find what appears to be 7 solenoids? Where to start?
View 1 RepliesMy F350 idles fine but every 10-15 seconds it mis fires. When asking it to go up hill it sputters and seems to loose power. It runs fine until asked to work hard. Not really sure which direction to go in first.
View 9 RepliesI have a 06 f350 with 5.4 140k miles. Recently it has been shaking bad on idle but only in gear and it's hard to start when cold. The exhaust is moist at all times and the fluids never leak. When you floor it it hesitates feels like it's overly rich but if you let off a little it stars to pull again. Also while cruising at 1500-1700 rpms in any gear it will surge and skip. Only time it will miss and the CEL comes on is over 4000 rpms for a random misfire. Just put new coils in new fuel pump and filter. There has always been a cat code but it never effected the drivability. Could it be injectors?
View 3 RepliesMy daughter has this truck and I was driving it the other day I noticed it misfiring when the trans shifts down under a slight pull and/or going up hills. It looses power and speed when this happens but if you back off, it smooths out when it shifts into overdrive. I haven't had it to a mechanic to check any codes yet.
View 3 RepliesI've got a 2000 F350 crew cab with a camper I bought in Chile and I'm going to be driving it from the tip of south america back to the US. It's a 9 month epic family road trip. It'll involve crossing the Andes several times and going over 15,000 ft. There are roads up to 19,500 ft in various places.
My question is am I going to have problems with the altitude? What can i do about it? I've got another truck which is a unimog, it's slow as hell but has a special kind of booster gas you can inject in to the engine to get it started in very cold weather and at high altitude. I chose the F350 for the truck instead of the unimog because a unimog is slow as hell (think 40mph max speed), but it handles extreme conditions well.
I have a 2000 f350 xlt and it has been very good until now. I can be driving normal and stop and park, when I get in and try and start it , it acts like the neutral safety switch is not working. the key turns and all my dash lights work, radio works, everything but the starter. I have to put it into neutral to get it to start. then after I stop again, it works fine. I don't get the problem all the time and I can't find a neutral safety switch.
View 8 RepliesI have a 2000 F350 cab and chassis 4X4 with V10 and a 5 speed manual (actually it's a 4 speed with overdrive). My problem is the engine seems to have a miss in it. When I first start it in the morning it usually runs good for 5+ miles till it warms up then if I am not pulling a load I can hear what sounds like a miss but the truck accelerates fine. If I am pulling a load I can also feel a slight steady consistent shudder and I can tell the truck doesn't have the power it should and the gas mileage SUCKS worse than it use to.
I ran a bottle of Lucas deep clean through a tank of fuel and that seemed to work a little but I will still encounter the problem sometime during the day. When the miss seems to be gone I can hear a very slight pinging noise when I accelerate or pull a hill with and/or with out a load. The pinging noise I hear sounds like an engine with a distributor that is getting to much spark advance if you have ever experienced that before.
I purchased this truck used several years ago and I don't know what the PO did but the check engine light is not coming on and it doesn't throw a code. I put 10 new ford coil packs on it about a year ago so I really don't think it's a coil pack, but I could be wrong. To me it sounds like maybe it an injector problem????? I know there are several sensors on this engine and I am thinking maybe a crank position sensor is not working right but I honestly don't know???? Is there a way to test this sensor?
I have a 2000 f350 5.4 liter I recently fixed a misfire in cylinder 1 since then every morning the truck runs perfectly fine however at night when I leave work around 6 o'clock the truck has a misfire again I stopped pullover pull the spark plug out put the spark plug back in and it runs perfectly fine all over again I don't know if this matters but when I replace the spark plug I only replaced one and not all 8 same thing with the new coil pack I don't see how that could cause this.
View 14 RepliesI recently purchased a 2000 F350 4wd, it's mainly used for plowing my driveway, and hauling larger items. I can truly say I love this truck. When I got it, it was in pretty rough shape, but slowly I've been bringing it back to life.
However, I have this loud front end rattling sound I can't seem to locate. Quick background the truck is 4wd with a v10 in it, and it has 215k miles on it, poorly maintained, so everything is suspect. Only new parts are all new brakes and new u-joints everywhere.
So back to the noise, it's most noticeable whenever I hit a small bump or dip at lower speeds, but the noise is still there at higher mph as well. It's loud and literally sounds like the whole front end will fall off, its a definite rattle, doesn't seem to be from one side or the other, best I can describe is in front of the firewall at it sounds like something is very loose.
But when I crawl underneath the truck, I don't see anything loose, the shocks, look OK, the sway bar links seem to be connected. IDK what else to look for, 4wd works fine and doesn't seem to alter the noise any when engaged.
Truck recently passed inspection, and no mention of anything being loose or worn was mentioned. I'm kinda at a loss, but the sound is so loud and noticeable I feel like it should be obvious as to whats loose underneath.
I'm getting a really choppy low RPM drive. If I'm above 2-2.5k rpm it runs okay but as soon as it drops under 2.5k it starts to run very choppy and loses power and Boggs in and out of power regardless of how much throttle input I give it. I had a tune up done last year and a recent oil change...
View 1 RepliesStarted my truck this morning. 2000 F350, V10, 153000 on the clock. Immediately sounded like a shotgun went off under the hood, now it sounds like it's running a cutoff exhaust. Had a tiny manifold tick prior to this, but can it backfire hard enough to crack/destroy the manifold?
View 5 RepliesThe 4wd on my 2000 f350 has just stopped working? I have used it a few times since getting it a few months ago and then last night I was going to play paintball in the woods and the 4wd would not engage? when i put it in 4wd it would act like the truck is in neutral and then it lurched forward? The front hubs have the option on them to turn, but I never had to turn them before and they do not move when I tried to? What could be causing the 4wd not to function?
View 4 RepliesSo I've got a 2000 F350 7.3. Just replaced all the ball joints, sway bar end links, carrier bearing, balanced the tires... a bunch of stuff to try and eradicate this weird wobble I have and I just can't seem to figure out what it is.
The wobble happens at and around 35mph, and then once I break 70mpis on the speedo (I have a 4" lift and am running 35's so it's not actually 70). I've experienced death wobble before in a jeep I had, and it is nothing like that, and I can't see it being driveline related but I could be wrong.
Here's what I have 2000 F350 XLT 105000 miles and a 4R100 tranny, was coming home from work no issues, stopped at my mailbox to retrieve mail.
when applying brake, it lunged forward a bit and stalled, I started back up put in drive, stalled again. started back up put in reverse, no issues.
I put in neutral revved it somewhat and it moved forward enough to start the roll down the small slope at my drive, I then started in neutral again as was rolling and then put into drive and drove 1/2 mile down my lane to house. backed up in my parking spot, no problems then shifted to drive and stalled.
Today I dropped the pan and checked the filter as I have read that sometimes they will fall out and cause same symptoms, filter was where it was supposed to be, no easy cure here.
I have a 2000 7.3L PSD and the light switch pulls out like the newer Fords do to activate their fog lights, I am just trying to find out if who has hooked up fog lights to this switch on a 2000? If so, how?
View 4 RepliesMy 2000 ford f350 will start and then dies on me when i try to put in gear. I changed air n fuel filter. Adding oil i noticed the stick was still reading dry. Noticed a big oil spot under the hood. What should i try to do? Do not want to put in shop cause every time she goes in I come out broke.
View 1 RepliesSo I went to start the truck this morning around 8:00 and it was 7 degrees outside, when the truck started the oil light came on and oil gauge was on low? So I turned it off right away. few hours later I tried it again and still nothing I thought maybe the oil was frozen. After I started the truck the oil was higher on the dipstick so I am assuming the oil pump is functional. What could be causing this? Could it be the the gauge is not working? The truck is a 2000 F-350 V-8 5.4 gas. I'm hoping it is something simple I am suppose to work this afternoon
View 14 RepliesIn my attempt to remove the auto locking hub on my 2000 F-350 4x4, I found that it would not slide out. I removed the retaing clip and the hub should of be able to come out with a couple wiggles, it seems to have seized inside the hub. I tapped it with a rubber mallet on all sides. Any thoughts as to other alternative methods of removing the hub locker ?
View 14 RepliesI have a 2000 F350. I'm tired of my gauge cluster. No matter what, within a year one of the LEDs has a diode that starts to flicker and flash and makes my gauge cluster dance. I'd like to solder in a series of individual LEDs and do away with the expensive bulbs that always fail. The bulbs I soldered into my HVAC have never given me any issue, so I figured this would be a good fix for that and the awful hotspots.
I have torn down the gauge cluster partially before. when you pull the gauge faces off as a unit (including the various electrical components tied to the back of the gauges), there is a circuit board at the top of the cluster. It has two cables that plug into the main face part that pulls away from the white plastic chassis. Need to successfully unplug the cables in order to separate the gauge assembly from the chassis? I don't like the idea of soldering so close to it while having the chassis part propped up.