I'm getting a really choppy low RPM drive. If I'm above 2-2.5k rpm it runs okay but as soon as it drops under 2.5k it starts to run very choppy and loses power and Boggs in and out of power regardless of how much throttle input I give it. I had a tune up done last year and a recent oil change...
View 1 RepliesHere's what I have 2000 F350 XLT 105000 miles and a 4R100 tranny, was coming home from work no issues, stopped at my mailbox to retrieve mail.
when applying brake, it lunged forward a bit and stalled, I started back up put in drive, stalled again. started back up put in reverse, no issues.
I put in neutral revved it somewhat and it moved forward enough to start the roll down the small slope at my drive, I then started in neutral again as was rolling and then put into drive and drove 1/2 mile down my lane to house. backed up in my parking spot, no problems then shifted to drive and stalled.
Today I dropped the pan and checked the filter as I have read that sometimes they will fall out and cause same symptoms, filter was where it was supposed to be, no easy cure here.
I want to install a new front drive shaft in my 2000 F350. I have the new one, and it has a big nut and it is threaded for length adjustment. My old one has a rubber boot which is missing from the new one. I plan on using red locktite but I do not know the torque specs on the front universal caps. Should I take it to my mechanic? I've never owned a 4x4 before.
View 3 RepliesMy 2000 F-250 6.8L V10 has a choppy idle during the first 30 or so seconds after a cold start up in the morning then it smooths out and drives perfectly. If I were to place the truck in gear during the choppy idle, it would not die and throttle response would be fine.
I cleaned the MAF sensor and checked the PCV elbow for cracks (no cracks). It idles at about a 1000 rpm during a cold startup then drops to about 750 rpm according to the dash tachometer. The truck has 187,000 miles on it.
I have a 2001 F350 7.3 4WD that does not want to shift into drive. When you shift to drive you can feel a slight difference in the trans but it will not move, it will rev freely but not move. If I shift it up and down it will engage after a lag period ranging from 10-15 seconds up to several minutes. Reverse is ok and after forward engages it appears to work as it should, shifts ok through the gears. I don't have much experience working on automatics.
View 4 RepliesSo loving my new to me truck. Only has 140K on it. But one thing that bugs me is that with the doors closed tight, when I drive over bumps, they sound like they are not closed. Makes you feel like they will fly open. But when checked they are closed all the way. Is there an adjustment or something that can correct this?
View 5 RepliesHave a 2001 f350 that runs great until you hook a trailer to it. Once a trailer is hooked to it and you are on a slight incline (and I mean slight) it will not go into D.. It's like it gets stuck in N.. Have to jam it into 1 to get it to go.. Once level again it will go back to D... Truck has 177k miles on it.
View 14 RepliesI have a 99 ford super duty with a 5.4 triton that is having a troublesome misfire. When you first fire it up it has a bit of a stutter then runs relatively smooth but the engine does still have a small shake to it and you can hear a bit of a choppy sound in the exhaust. Not completely smooth. When you drive it light footed it seems to run perfectly smooth and nice. But if you go past half throttle (sometimes you can go past that point) it starts to cough and is very slow at picking up.
When you reach between 3,250 and 4,500rpm the coughing stops. But the pick up is a little surgy, not steady. It was doing this for a while before the engine light came on. I got it scanned and it showed a miss fire on cylinder two so I have replaced the spark plug, coil, and injector but still the same issue. I opened up the catalytic converter to see if it was plugged up. Nothing there.
My F350 4x4 won't go into 4 wheel drive unless I get out and take them out of auto and put them in locked position and when I have it in lock mode it seams to work like it's in auto mode, when I put the switch on the dash in 2wd, it seams like it's only driving the back wheels....
View 14 RepliesI have a 2004 F350 Crew Cab DRW 4WD 6.0L.
The front drive shaft is making a high pitched metallic squeal while the truck is in motion. I thought it might be the universal joints but after lubricating the joints, I can still hear the squeal and it sounds like it is coming from inside the drive shaft. I also hear this squeal when I spin the drive shaft by hand.
I have quite a few questions about these drive shafts:
- What would cause a squeal from within the drive shaft?
- Are there any replaceable parts or do I have to get a new drive shaft?
- How do I identify the correct drive shaft part for my truck? Seems like there are a LOT of different models on the web.
- Are any of the aftermarket drive shafts any good? Any to avoid?
- Is this a DIY job or will I need to take it in to the shop?
One of our trucks, 2004 F350 Powerstroke, my company truck, recently the last snow even we had, my tow haul mode would pop on and off almost evertime I shifted from drive to reverse while plowing. I didn't want it on, it just kept poping on and off. Thought maybe the button was stuck, but it moved like normal. My other thought was there is a loose connection in the shifter or column causing it to go on and off.
View 6 RepliesHave an f350 4x4 diesel that when I drive slow and especially turn to the right it makes a grinding noise. It seems to either go away or just gets muffled by road noise when cruising. The ball joints were bad so I replaced them and I figured with this especially when I turn right it had to be a wheel bearing so I replaced both of them and still same thing. Don't want to throw money at it hoping to fix the issue. Also front duff is full of oil.
View 5 RepliesThis must have been asked before but I couldn't find any thread about it. Have a 2006 F350 that makes a rattling sound when engaged in front wheel drive. Sounds a bit like a loose ball from a ball bearing (or a small stone) rolling around. What might be causing this?
View 3 RepliesI just picked up a 2005 SC LB 4x4 5.4 v8 6mt F-350 yesterday and drove it about 250 miles home. It is my first Super Duty, and I love it so far but... the steering has some issues. There seems to be decent amount of play in the steering wheel when I'm driving straight. Also, the truck drives straight when the steering wheel is turned about 30 degrees to the left, and I would like to fix that and bring it to center. When I was cruising on the highway (65-70 mph), there was also two 20 minute periods of time spaced an hour apart where the steering would get light and the truck would dart to the left (i do not think road conditions were a factor as it did not happen on the worst stretches of highway. The truck has 133,000 miles on it, and has had pretty routines maintenance done on it, as it was owned by a drilling business as a work truck to haul tools. The guy I bought it from said that it needed the steering shock/damper replaced, so I will do that, but what else to you think I need to do to the truck?
View 2 RepliesI have a 2000 f350. When idling uo can't really hear the miss. Driving at about 40-50 mph it will shack and shutter real bad. Hooked up spanner and had miss fire codes for cyl. 1,4,9. Changed out all 10 plugs, and boots. Also changed out the coil on all three cyl also. Still have the miss and shutter. Also changed out #9 injector ...
View 12 RepliesI've got a 2000 F350 crew cab with a camper I bought in Chile and I'm going to be driving it from the tip of south america back to the US. It's a 9 month epic family road trip. It'll involve crossing the Andes several times and going over 15,000 ft. There are roads up to 19,500 ft in various places.
My question is am I going to have problems with the altitude? What can i do about it? I've got another truck which is a unimog, it's slow as hell but has a special kind of booster gas you can inject in to the engine to get it started in very cold weather and at high altitude. I chose the F350 for the truck instead of the unimog because a unimog is slow as hell (think 40mph max speed), but it handles extreme conditions well.
I have a 2000 f350 xlt and it has been very good until now. I can be driving normal and stop and park, when I get in and try and start it , it acts like the neutral safety switch is not working. the key turns and all my dash lights work, radio works, everything but the starter. I have to put it into neutral to get it to start. then after I stop again, it works fine. I don't get the problem all the time and I can't find a neutral safety switch.
View 8 RepliesI have a 2000 F350 cab and chassis 4X4 with V10 and a 5 speed manual (actually it's a 4 speed with overdrive). My problem is the engine seems to have a miss in it. When I first start it in the morning it usually runs good for 5+ miles till it warms up then if I am not pulling a load I can hear what sounds like a miss but the truck accelerates fine. If I am pulling a load I can also feel a slight steady consistent shudder and I can tell the truck doesn't have the power it should and the gas mileage SUCKS worse than it use to.
I ran a bottle of Lucas deep clean through a tank of fuel and that seemed to work a little but I will still encounter the problem sometime during the day. When the miss seems to be gone I can hear a very slight pinging noise when I accelerate or pull a hill with and/or with out a load. The pinging noise I hear sounds like an engine with a distributor that is getting to much spark advance if you have ever experienced that before.
I purchased this truck used several years ago and I don't know what the PO did but the check engine light is not coming on and it doesn't throw a code. I put 10 new ford coil packs on it about a year ago so I really don't think it's a coil pack, but I could be wrong. To me it sounds like maybe it an injector problem????? I know there are several sensors on this engine and I am thinking maybe a crank position sensor is not working right but I honestly don't know???? Is there a way to test this sensor?
I have a 2000 f350 5.4 liter I recently fixed a misfire in cylinder 1 since then every morning the truck runs perfectly fine however at night when I leave work around 6 o'clock the truck has a misfire again I stopped pullover pull the spark plug out put the spark plug back in and it runs perfectly fine all over again I don't know if this matters but when I replace the spark plug I only replaced one and not all 8 same thing with the new coil pack I don't see how that could cause this.
View 14 RepliesI recently purchased a 2000 F350 4wd, it's mainly used for plowing my driveway, and hauling larger items. I can truly say I love this truck. When I got it, it was in pretty rough shape, but slowly I've been bringing it back to life.
However, I have this loud front end rattling sound I can't seem to locate. Quick background the truck is 4wd with a v10 in it, and it has 215k miles on it, poorly maintained, so everything is suspect. Only new parts are all new brakes and new u-joints everywhere.
So back to the noise, it's most noticeable whenever I hit a small bump or dip at lower speeds, but the noise is still there at higher mph as well. It's loud and literally sounds like the whole front end will fall off, its a definite rattle, doesn't seem to be from one side or the other, best I can describe is in front of the firewall at it sounds like something is very loose.
But when I crawl underneath the truck, I don't see anything loose, the shocks, look OK, the sway bar links seem to be connected. IDK what else to look for, 4wd works fine and doesn't seem to alter the noise any when engaged.
Truck recently passed inspection, and no mention of anything being loose or worn was mentioned. I'm kinda at a loss, but the sound is so loud and noticeable I feel like it should be obvious as to whats loose underneath.
Started my truck this morning. 2000 F350, V10, 153000 on the clock. Immediately sounded like a shotgun went off under the hood, now it sounds like it's running a cutoff exhaust. Had a tiny manifold tick prior to this, but can it backfire hard enough to crack/destroy the manifold?
View 5 Replies