Ford Super Duty (1999-2016) :: 2000 F350 Truck Will Crank But Not Start
Oct 10, 2014
We just bought a 2000 F350 knowing it has some issues. The #5 fuse (generator/secondary) under the hood consistently blows fuses the second it's inserted, meaning there's a dead short. Truck will crank but not start. As well, theres a 5 amp fuse under the dash, which when inserted, keeps the instrument cluster on as if the key was on, even with no key in the barrel. We cannot hear the fuel pump running, the fuel reset switch is fine, all ignition wires at the column are showing 12 volts at the right times. What could be wrong? I'm a 12 volt specialist, but not a ford tech.
View 6 Replies
Advertisement
I have a 2000 f350 xlt and it has been very good until now. I can be driving normal and stop and park, when I get in and try and start it , it acts like the neutral safety switch is not working. the key turns and all my dash lights work, radio works, everything but the starter. I have to put it into neutral to get it to start. then after I stop again, it works fine. I don't get the problem all the time and I can't find a neutral safety switch.
View 8 Replies
I have 99 f350 single rear wheels 4x4 . I went to start it this morning and it would crank but not start b/c it was cold. I plugged it in and still wouldn't start then it wouldn't even crank. I checked all fuses swapped relays and I have new batteries. The last thing I did was hit on the starter a few times and it started. So I went and bought a new not remand a new starter and put it on and now it won't crank!? I get 12v at the little wire on the selenoid on the fender. So now what?
View 4 Replies
Last night my truck wouldnt start. Drove fine all day, started up bunch of different times. Went to go home at night. No crank, everything else works, hear the fuel pump prime windows radio everything. smacked the starter a few times but no change. Checked the fuses and relays, all appear good. So im guessing the starter or the starter solenoid, but I cant find one on the truck just something that looks like it could be it attached to the starter.
View 9 Replies
So I went to start the truck this morning around 8:00 and it was 7 degrees outside, when the truck started the oil light came on and oil gauge was on low? So I turned it off right away. few hours later I tried it again and still nothing I thought maybe the oil was frozen. After I started the truck the oil was higher on the dipstick so I am assuming the oil pump is functional. What could be causing this? Could it be the the gauge is not working? The truck is a 2000 F-350 V-8 5.4 gas. I'm hoping it is something simple I am suppose to work this afternoon
View 14 Replies
Having an issue with my 04. Wife got in the truck to move it and no dome lights no crank nothing. Swapped the battery for a new one. Still nothing.
I checked all fuses. I literally was just driving it 10 months prior to her getting in it. Said dome came on for a second then shut off. 2004 F350 5.4 ....
View 3 Replies
So here's the deal, crank no start its getting fuel. Has base oil pressure and i put a ficm on that test good with a voltage meter key on engine off and cranking. I haven't hand any trouble finding info on this issue so. We can keep picking away. Just cant find anything about this.
A buddy of mine who has been trying to figure it out for me, Got it to start using a starting fluid. And it would run if someone was pushing the gas peddle but wouldn't idle. Or start without the starting fluid.
View 2 Replies
Last night it was surging at idle and then just died. It had a code on it about the crank sensor not communicating... no codes this morning and it wont start.
I just bought the damn thing 3 weeks ago and its already not running. Where do I start to diagnose this damn thing..........
View 7 Replies
I have a 2000 f350 v10 ext cab 8 ft bed 4wd,i replaced all 10 plugs all 10 coils at 40 mph the truck violently shakes an vibrates read on a few things that could be crack cylinder or bad pistons,i did a test on it an says low compression in 2 cylinders 1&2 what can I do an what is the best option for me as I just got the truck not even a month ago...
View 3 Replies
2003 f-350 had no dash lights and no start or crank. Found battery cable junction on left fender broken fixed, replaced starter. Drove it sunday, went about 15 mi and just shut off. Towed home was a battery, replaced battery, now I have lights but turn key and nothing? Was starting fine, all summer seems like a cold weather issue. Any relays I should be looking for? I was going to check power to started but raining too hard this am ...
View 4 Replies
I have a 2012 Ford F350 I've been looking to install a compressor on. I've poked a hole in the gasket that runs wires through the firewall and cut the tips off of a couple of the accessory wires. Went to go get some more parts and now the truck won't start! The lights and radio turn on when the car is turned on but the starter doesn't even click when I try to start it. What should I look at?
View 7 Replies
i have a 01 Ford F-350 7.3L quite and won't start I have replaced the ipr valve and sensor and the crank sensor and the truck still won't start...
View 1 Replies
So I 2003 6.0 F350 that is a Dually. Been sitting in my yard for about two years now. I turn the key it just clicks and it doesn't crank. The starter solenoid is not on the firewall so I use the trick with the battery connected positive straight to the starter with the whit The starter solenoid is not on the firewall so I use the trick with the battery connected positive straight to the starter with the wire on the engine bay. It cranked for a while and that started ran rough. Then it just died. I did not start again. I did this during winter so the engine have time to cool off it was about below freezing. Done this multiple times and drove up and down in my backyard but not on the road. What could be wrong with it. Either way I put in diesel 911 and more fuel but and I change the filters with Motorcraft OEM filters. Sure that the caps were right.
View 14 Replies
I'm just a shade tree mechanic try to diagnose a hot crank no start condition on my 2006 F-350 6.0 that I purchased second hand about six months ago. I first took it to a diesel shop to have them fix it and the mechanic told me that the stand pipes and dummy plugs needed changing out but couldn't tell me 100% if that would fix the hot no start problem.. I have been reading a lot about this problem and it seems that the snap to connect fitting on the HPOP is the most common problem on these trucks. It seemed easy enough to do so I went after it only to find it was already replaced with the updated part.
I went ahead and changed it anyway but it obviously didn't work. So today I pressurized the system through the ICP port with my small harbor freight compressor up to 80 psi and forced the IPR valve closed with 12v. I then listened for a leak in the passenger side valve cover with a hose stuck in the oil fill cap, the driver side cover from some drain hole under the air filter housing and in the oil filter housing. I could hear a mild hissing from the driver side and the oil filter housing but it was clearly louder from the oil fill on the passenger side. This leads me to believe I have a top seal leak from one of the injectors on the passenger side, but not 100% sure. Should I be hearing anything at all from the driver side and from the oil filter housing if its a bad seal in the passenger side?
Another problem I just found out I have seems like maybe fuel in the oil. I done a oil change this week after 3500 miles since last change and drained out five gallons of oil!! The oil seemed really thin. My coolant level is still good so the only thing I can think of is fuel dilution. Could this possibly be the same o ring or injector that is causing my hpo leak or something else? Will a bubble or balloon test diagnose this?
I bought a cheap OBD2 reader that works on my Ipad with a app called Dashcommand so I can see what codes were stored. The codes are...
P0401- Exhaust Gas Recirculation A Flow Insufficient Detected (EGR has been deleted)
P0528-Fan Speed Sensor Circuit No Signal
P0670-Glow Plug Control Circuit/Open
P0683-Glow Plug Control Module to PCM Communication Circuit
P2290-Injection Control Pressure Too Low
So far my thoughts are to replace the injector and nipple cup seals to take care of the hpo leak. Once I have the valve cover off, clean the injectors real good and cycle the fuel pump with turning the key on and inspect the injectors for a fuel leak. Is there a better way than this?
View 8 Replies
So I just purchased a 2011 F350 6.7 this week...I've had absolutely no problems until I drove it to the dealer just to get it detailed...I give the salesman my key and he comes back and says it won't start...we tried numerous time to start it...put jump boxes on both batteries and nothing...had full power to all accessories but when attempting to crank it would black out on the dash screen and give me a "stop vehicle" warning....does this deal with security?....also after hassling to get rental for a hour or so,we tried agian and it fired right up?!?...also it started double honking when locking. ..is that due to the hood being up?
View 3 Replies
I recently bought a 2003 f350 7.3, I ordered a tuner for it and tried installing it, at one point while the ECM was still connected I did something and it sparked. Then the powertrain relay (302) started clicking really fast. It clicked in the on position. I switched it with another and it was also clicking. So since I sparke the ECM I figured I messed it up. I ordered another one and it's doing the same thing. Then I pulled fuse 45 (which was good) and put it back in. When I turned truck to on position it wouldn't click anymore, but it still won't start... What it could be? OV ruled out the ECM, powertrain relay (302) and fuse 45, I don't know what else to check.
View 2 Replies
Where the ICP is located on a 2006 f350? I have a no start condition after the truck warms up, everything else is fine. Started fluid works to crank, I suspect the ICP and /or Orings.
View 4 Replies
It's an 04 F350 6.8L This past winter when it was cold I would start it up and it would rock forward and bounce back as is you shifted in to park while rolling. Now that it's warmed up it won't jerk forward but the whole body shakes only at start up. As much as I like the idea of of the raw torque being so powerful the truck twists with power I don't think that's the case.
View 5 Replies
My 2000 ford f350 will start and then dies on me when i try to put in gear. I changed air n fuel filter. Adding oil i noticed the stick was still reading dry. Noticed a big oil spot under the hood. What should i try to do? Do not want to put in shop cause every time she goes in I come out broke.
View 1 Replies
I recently caught up on some maintenance with my truck, changed the turbo pedestal seals, replaced both batteries, brakes, e-brake cable etc and installed new 10k hid headlights. its a single cab 250 with a 7.3 and zf6 4x4 with 133k. a couple days ago I turned on the headlights and the truck died, restarted no problem and would die the next 5 times I tried to turn them on, then it worked fine. yesterday I got in my truck to leave for work and got no wait to start light, no glow plug chatter, no fuel pump running. turns over just fine but no fire.
I got a ride to work and tried it when I got home, fired right up. I pulled the pCM, checked it out, no weird smells and my TS chip wasn't corroded or anything like that, worked fine. drove to 711 to get a 6 pack and it did the headlight thing again. I removed the HIDs because this all started after I installed them and reinstalled my silvanias and it didn't die when I turned them on. this morning went to leave for work, same no start condition. I disconnected both batteries for 30 seconds to reset anything and same problem. I was about ready to light it on fire this morning.
View 1 Replies
I just bought a 2000 F250 SD, 4x4, 5.4, Quad Cab. I drove it off the lot, stopped to put air in the tires, jumped back in and it wouldn't crank. All of the dash lights worked fine. Tried jumping at the starter solenoid and got nothing. Got under the truck and jumped it off the starter, vroom, fired right up. Replaced the starter solenoid and had no issues for about 2 hours. Then it did it again. This time it wouldn't start at all. I towed it back to the dealer and they had it for 3 weeks.
Then yesterday I called and they said it was done. Picked it up, drove to the barber shop, got my hair cut, came back out and it did the same thing AGAIN. After jacking around with the shifter and turning the wheel back and forth 100 times it started. The key is kind of hard to turn sometimes in the ignition, so I'm thinking that the ignition cylinder needs to be lubed real good, but that shouldn't stop it from cranking the motor over, right? I was going to swap out the ignition switch, but I don't know if that will do any good either.
View 3 Replies
