Ford Super Duty (1999-2016) :: 2000 F350 - Gauges / Speedometer And Tach Stopped Working
Mar 5, 2014
I have a 2000 F350 4x4 with 7.3L diesel and a manual transmission. While driving home yesterday my gauges (fuel, temp, volts, oil pres) stopped working. Within a couple min the speedometer and the tach also stopped working, but the truck was still running fine. Within a couple miles the engine stopped running, just like I had turned the engine off.
After having it towed home I checked all the fuses, none are blown, but there is no power to fuse #16 (15A, instrument cluster, high beam head lamp). Also in the fuse box under the hood, again, no fuses are blown, but fuse #9 (left head lamp low beam) and #11 (right head lamp low beam) have no power to them.
View 3 Replies
Advertisement
The 4wd on my 2000 f350 has just stopped working? I have used it a few times since getting it a few months ago and then last night I was going to play paintball in the woods and the 4wd would not engage? when i put it in 4wd it would act like the truck is in neutral and then it lurched forward? The front hubs have the option on them to turn, but I never had to turn them before and they do not move when I tried to? What could be causing the 4wd not to function?
View 4 Replies
I have a 2000 f350 XLT SD v10 gas. The radio works, the heater works and the power windows work too. It's just the cluster. Lights work in the cluster it's the gauges are dead truck starts fine.
View 2 Replies
I have a 1999 f250 7.3 ... l extended cab 4x4 super duty ... ABS light on, over drive light flashing and speedometer has stopped working .. I have replaced abs senor on the rear of transmission and on the rear end.both new and just replaced abs module just the computer not the pump that was used . And abs light, overdrive light are still on and the speedometer is still not working ..
View 14 Replies
2005 6.0 F350 dually, speedometer quit working and the ABS light came on. I replaced the speedo sensor in the diff, but to no avail. Hear a lot about the cluster, however nothing with the ABS light on.
View 3 Replies
My father-in-law has a 2008 f-250 with the 5.4. as he was driving a while back all the gauges of the dash quit. The engine still kept running without any noticeable difference but when he shut the engine off and tried to restart, it wouldn't even crank but the security light was flashing. He tried starting it again a few hours later and it started just like normal and ran fine.
He has had this problem occur several times in the last few months, but the other day it repeated the problem again and would not restart for about 5 days. He has tried charging the batteries, changing relays, checking all fuses and finding none blown, scanned it with his code reader, and checked the steering column for bare or rubbed wires.
View 10 Replies
The interior lights, radio, and power window gauges and the ignition buzzer on my 2002 F350 quit working. What could cause this? Everything else still works.
View 7 Replies
Ihave a 2004 F350 4x4 Dually diesel. While in my hay field I hit a small rut and the truck bounced. About two seconds later all gauges and lights/windows quit working and the truck ran rough. I have a Banks system and it registered a code 33. Maybe 32 error. Book says it is an airbag deployment. They did not deploy. So I drove out of the field and turned it off to see if that would reset the gauges. No, not only that but the gauges all swept the faces from off to full to off and the truck would not start, just chatter.
I disconnected both batteries and waited. Reconnected and it started, but the gauges quit after 10 seconds..... Everything flatlined even the banks IQ. But the truck kept on running. Got back to the ranch and the batteries went flat overnight... Charged them up, starts fine gauges work but alternator puts out 11.5.
View 2 Replies
I have a 2001 F250, 5.4, 4X4. My ignition key stuck in the start position and when I pulled it back to the run position, everything seemed ok. As I started down the road, my speedometer stopped working and my overdrive light was flashing. Also my turn signals had stopped working and my A/C clutch didn't engage. Figured I burnt a fuse. I looked in both the under dash and power distribution box and all seemed well. I checked the fuse for the turn signals/flasher and it was fine. The flashers worked. Thought I might have fried something so I replaced the ignition lock and switch. Also my service engine light came on throwing a code for the vehicle speed sensor.
Looking for solutions on this forum and the internet, I learned that the turn signal switch could have gone bad and the VSS sensor is on the top of the rear dif and an easy fix. Well replaced the sensor but nothing changed. So I went back to the fuse box. Examined every fuse, big and small and I found a 10a with a small space. This was #24 under the dash. From the manual, "#24, 10A, A/C clutch, Blend Door Actuator, Trailer Tow Battery Charge Relay Coil, Four Wheel Anti-Lock Brake System (4WABS), Turn Signal." Replaced it and everything went back to normal. Turn signals work, A/C clutch works, no flashing overdrive light and speedometer works. All from a 10A fuse. If you have any of these symptoms examine all the fuses carefully. There's a 20A fuse for turn/hazard lamps and this other one buried that's only 10A.
View 1 Replies
2002 f350 7.3 diesel automatic. The cruise stopped about a 1/2 year ago and i have done the recall and replaced the steering wheel switch. but it still doesn't work. the horn works and speedometer works.
View 4 Replies
I own a 1999 F350 CC SRW w/ 7.3L PSD engine. My turn signals stopped working suddenly. I've checked the fuse panel under the dash but it doesn't show any fuse for the turn signals.
My hazards do work although I noticed something very strange. When I tilt the steering column down the hazards stop working and when I tilt the column all the way up they work again. Still no turn signals though.
View 1 Replies
I have a 2009 f350 xlt with sync and steering wheel controls that the stereo quit working on and I want to replace and I am having trouble finding the correct one that will work with sync. One of the local auto wreckers has a 2010 f350 lariat with the touch screen that they are willing to let go for a reasonable price. Will that head unit work in my truck without major wiring?
View 1 Replies
I am working on my son's 1997 F-150, 2 wheel drive, 4/6L truck. He was driving it when the gauges and the tach stopped working. I replaced the cluster and it still blows the fuses. The five amp fuse that is specifically for the cluster doesn't blow. It is a twenty five amp fuse that also power the overdrive circuit, etc.
After replacing the gauge cluster I installed a new fuse and the overdrive button on the shifter started smoking. Where I could get a wiring diagram of this circuit so I can see how it is wired.
View 2 Replies
Having a problem with my truck and I'm stuck. About 9 months ago my 4wd stopped working. Turn the switch and no light or noise. I took a look at fuses and everything was good there. I let it go but now I need 4wd. Today I checked every fuse and all of them were good. I moved to the relays checked them and they were good but for the heck of it replaced them. Checked for power at the pins. The one that needed power had power. Next I went to the switch had 12 volts there. Pulled switch and test with a multimeter and ohms were good. Went. Down to the motor and tested for power there not power to the motor. Is there anything else I'm missing Esof not working. 2002 f350 7.3 auto....
View 2 Replies
My windshield wipers aren't working. I can hear the relay click and I've checked the fuse. I found this ground wire, what it goes to?
View 1 Replies
My door locks stopped working new battery in fob, I can hear them trying to work. 2000 f250 crew cab .....
View 3 Replies
I have a 1999(03/98 Production Date) F350 DRW Dump 5.4L Reg Cab. I just replaced the ECM (Drivers side Kick plate) with a used ECM
1. Crank but no start, gauges worked.
2. Replaced the ECM (Drivers side Kick plate) with a used ECM
3. Truck now starts.
4. None of the Instrument gauges work. No gas gauge, no speedo, no tach, no bat no odometer or trip odometer. Not one single gauge works.
Does the ECM need to flashed for the cluster to work or might it be a separate issue?
View 2 Replies
I have a 2000 F-350 Dually. One of the rear fender lights is not working. Is there a way to check the bulb without pulling the inner liner to access it?
View 5 Replies
My prob started with key in ignition warning alarm working with no key, then radio on off at will and interior light not working or delay not turning them off when door closed. Now all gauges and warning lights/alarms go out also. If I open door and key alarm is on all systems work at that moment and without touching truck alarm can stop at will, at that point ignition alarm, interior light, radio and gauges do not work. When I giggle key with truck running the door ajar alarm activates when system working!
View 4 Replies
I have an 2005 F350 4x4, 6.0 with 294000 miles. My gauges recently started to shut down on there own and then recover. at any speed with no effect on the engine. When I park and shut the system down, they all come back on again at start-up. However, they shut down again and then operate at will as I drive. What's causing this?
View 1 Replies
Just got a new-to-me 2006 F350 Super Duty XL with the 5.4L V8 and 5-speed auto. I haven't had a full-size truck in a few years and forgot what I was missing!
When I bought the truck, all gauges were inoperative except for the fuel and oil pressure gauges. The previous owner told me they would work intermittently and at some point just stopped. The usual warning lights - ABS, CEL, and "the wrench" - were all lit, and from Googling and searching this forum, it looked like an easy fix - probably a pinched or frayed shifter wire, or possibly a cluster repair.
I took it home and did a self test on the gauges. The "sweep gauges" made everything swing fine, so I was thinking it might not be a problem in the cluster. I pulled the steering column apart, removed the Tow/Haul overdrive wire from the plastic retainer, re-ran it with some slack, taped the end where it comes out of the shifter (even though I saw no breaks/frays) cleaned the connections, gave it a dollop of dielectric grease in the connector, and put it all back together. VOILA - GAUGES and no warning lights! You can imagine the touchdown dance in the driveway.
Fast forward a few weeks and....back to no gauges and warning lights lit. Figuring the overdrive wire had finally given up, I ordered and installed a replacement shifter figuring it was an easy and cheap fix. No joy - same problem. Tried cleaning and reseating the connection. Nothing. I've searched FTE like mad and it seems like 95% of the problems are with the wire exiting the shifter fraying and/or blowing a fuse, but this is a new shifter. I've also checked fuses #2, #24, #33, #36, #41, and #45 (some referenced #19 but I don't have a fuse there). All were unbroken - just put them back in and reseated firmly. I did a code pull via OBD2 and have a "rear catalytic efficiency degraded" code...not sure if that's related, but figured I just had an exhaust issue.
I may take the dash cover off and try to clean and reset the connections on the gauge cluster, as well as do the same for the PCM. Is it possible that the tow/haul overdrive wire to the PCM (where the shifter connects to) is bad? How to test and/or replace if it comes up bad?
View 14 Replies
