Ford Super Duty (1999-2016) :: 2000 F350 Front End Vibration When Hit A Little Bump On The Road?
Aug 17, 2015
2000 F350. 4x4, V10. 153,xxx miles. Here's the story. Whenever I hit a little bump in the road, I get a vibration directly under my feet and in the gas pedal, NOT in the steering. It will go away pretty quick or when I hit another bump. It only happens when the front driveshaft is not spinning. Hubs locked in in 2WD, it doesn't vibrate. Hubs unlocked and in 4x4 High it doesn't vibrate.
View 8 Replies
Advertisement
Problem: 55-60+ mph hit a bump front end shakes violently. Slow down to 40 mph it stops. DOES NOT happen every time, and may only happen once a week, but when it does my whole front end feels like it will come loose.
Solutions to date that have not worked:
1. Rotate and balance tires. (tire shop)
2. New shocks. (me)
3. New steering stabilizer. (me)
4. Changed ball joint and bushing in track bar. (Dealership)
5. Check ball bearings and seem to be ok. (me)
6. Check tie rod ends and are ok. (Dealership)
The only other options people have given me:
1. Dual Steering Stabilizer. (Have had truck since Jan and hasn't done it in about 19,000 miles. Why would it need it now? Truck has 109,000 miles on it.)
2. New tires. (If it were the tires wouldn't it do it all the time? )
View 14 Replies
So I've got a 2000 F350 7.3. Just replaced all the ball joints, sway bar end links, carrier bearing, balanced the tires... a bunch of stuff to try and eradicate this weird wobble I have and I just can't seem to figure out what it is.
The wobble happens at and around 35mph, and then once I break 70mpis on the speedo (I have a 4" lift and am running 35's so it's not actually 70). I've experienced death wobble before in a jeep I had, and it is nothing like that, and I can't see it being driveline related but I could be wrong.
View 1 Replies
I'm having trouble finding the source of a vibration in the front end if my 1999 f350 super duty 4x4. The vibration is felt all the time but worse when under 40mph, while braking, and especially when turning.
I have replaced the rotors and brakes, tie rods and Drag links since the issue started but no change. In the vibration. What should I check next?
View 4 Replies
I purchased the truck from a used car lot about 3 months ago and after driving for a few thousand miles I am feeling a slight wobble after hitting a bump in the road. Here is my truck set up:
- 2011 Ford Lariat F250 4X4 FX4 6.7 ltr
- 67400 miles
- Tires stock and great tread
- Rancho steering stabilizer kit
- Rancho Shocks
- Rear air bags
It does appear one of the rancho stabilizer dampers is leaking slightly. Why would the previous owner install a rancho stabilizer kit? Is it because of the rear air bags?
View 14 Replies
I recently purchased a 2000 F350 4wd, it's mainly used for plowing my driveway, and hauling larger items. I can truly say I love this truck. When I got it, it was in pretty rough shape, but slowly I've been bringing it back to life.
However, I have this loud front end rattling sound I can't seem to locate. Quick background the truck is 4wd with a v10 in it, and it has 215k miles on it, poorly maintained, so everything is suspect. Only new parts are all new brakes and new u-joints everywhere.
So back to the noise, it's most noticeable whenever I hit a small bump or dip at lower speeds, but the noise is still there at higher mph as well. It's loud and literally sounds like the whole front end will fall off, its a definite rattle, doesn't seem to be from one side or the other, best I can describe is in front of the firewall at it sounds like something is very loose.
But when I crawl underneath the truck, I don't see anything loose, the shocks, look OK, the sway bar links seem to be connected. IDK what else to look for, 4wd works fine and doesn't seem to alter the noise any when engaged.
Truck recently passed inspection, and no mention of anything being loose or worn was mentioned. I'm kinda at a loss, but the sound is so loud and noticeable I feel like it should be obvious as to whats loose underneath.
View 6 Replies
2001 f350 4x4 dually 7.3 powerstroke, I recently replaced the hub assembly, stub shaft and seal, u joint, ball joints on the front drivers side and now periodically the truck makes a grinding growling vibration coming from front drivers side and stops after hitting a bump...
View 3 Replies
I want to install a new front drive shaft in my 2000 F350. I have the new one, and it has a big nut and it is threaded for length adjustment. My old one has a rubber boot which is missing from the new one. I plan on using red locktite but I do not know the torque specs on the front universal caps. Should I take it to my mechanic? I've never owned a 4x4 before.
View 3 Replies
The issue is with my 2000 F350 crew longbed V10. Other than a BTS trans put in a little over a year ago, and FoMoCo motorsports headers, the whole truck is bone stock. Oh, it has that fantastic auto-hub thing with the fake locking hubs and the little switch on the dash (I'd love to convert it to a manual shifter...?). 174k on chassis, so things need to be done, 40k on engine, 3k on BTS 4r100.
Yesterday I was running around town, made a stop, and when I started moving again got a loud grinding from the front axle. Thought maybe I'd picked up a rock in a caliper or something, so I jumped out and checked everything, no joy. Moved forward, there it is again. No vibration, but loud enough (or telegraphing enough) to hear clearly in the cab. Let the truck roll forward, popped in to neutral, noise fades away. Back in to drive, there it is. So, now I know it's trans/t-case/driveshaft/related. I recently put new vacuum lines in, checked all the connections, and pulled, cleaned and lubed the hubs.
And since the trans is a nearly new BTS that is working just find, I'm narrowing the search to the hubs, drive shaft, t-case.
Get home (noise abates above 30mph, or everything else drowns it out), crawl under, and find the front driveshaft is locked. Ok, stuck hub? Pull out both the fake locking hubs, and now the shaft turns. I can turn each front axle by hand at the u-joint, and I kinda hear a faint grinding on the right side (will bad needles make noise only under a load from the trans and not coasting in neutral?), and when I swing the drive shaft around the left axle moves, right doesn't, etc etc.
I'm going to pull the drive shaft today and check the U joints, and drive a bit to see if the noise is still there, but I am thinking I might have some bad needles on the pax side axle...
View 4 Replies
My front passenger leaf spring just broke on my 2000 f-350. My front springs are T code, but I was wondering if a could replace the broken one with a code X spring as a temp fix until I get a leaf spring replacement delivered?
View 1 Replies
01 F350...4R100/V-10/4wd. Sometimes get a vibration driving down the road. First thought of tire out of balance but then the vibration goes away and may not come back for a few days or more. It starts sometimes around 30-40 mph and stays all the way up to around 65 mph. Even slowing down it vibrates or shakes. I can stop and take off again with nothing happening. Would think tires out of balance would do it all the time. And a few times....pulling my 5th wheel...making a right turn out of a parking lot.....it feels like a rumble from the rear.
View 2 Replies
My truck is a 2002 F350 CC dually longbox 4x4 7.3 auto that I bought last fall. On the street it is very well behaved although I suspect it is not giving me as much power as it should be, as compared to my previous 95 powerstroke.
Off road, slow crawling, the throttle is very jerky. Under acceleration it is smooth, but if I try holding a low throttle position, the rpm rises and falls. I am certain this is a bad TPS, and may also be contributing to my perceived low power on the street.
I have googled my brains out and it seems there is a cheap replacement TPS for earlier trucks but the 2002 has the 5 wire combined TPS and IVS, which reportedly is not replaceable without replacing the whole pedal assembly. To complicate matters I have the adjustable pedal assembly
So are there any options other than buying a complete pedal assembly from ford? Can I save some bux and retrofit a non-adjustable pedal assembly? I saw a youtube video where a guy put a newer 6.0 pedal assembly in but he was short on specifics about what exactly he gained doing this.
View 1 Replies
I am installing a set on a '12 F350 for a customer. I already had to go buy an additional hardware in order to get the back bumper on correctly...and now I'm looking at the front bumper and I swear I don't have the parts I need to install it. It appears to be missing some brackets. There were NO instructions with them (apparently a chronic problem with Road Armor) and I can't possibly imagine it bolting to the flimsy brackets that hold the factory bumper (fairing would be a better word for it) in place.
View 6 Replies
I have a 1997 f-350 crew cab 4x4 w/ off road package and 7.5 fuel muncher power package. My engine stalls going down the road w/ no warning. Sometimes it will start back up immediately, and other times not until i cycle the ignition 6 times or so.it seems to be getting worse as time goes by. Since it started i replaced tps, cap, rotor, plugs and wires. I also replaced fuel tank and pump and filter about 1.5 years ago. Some other issues to clear up, but concerned w/ current problem.
View 2 Replies
I have a 2005 king ranch and have a clunk coming from the back over bumps/heaves in the road. It doesn't happen all the time but often enough. I just replaced the shocks, that worked a little but didn't solve the problem. Now thinking rear sway bar end links? Anything I can check/inspect?
View 1 Replies
I put new ball joints on a few months ago and now the truck is starting the death wobbles felling even around slight bends in the road.I jacked it up and the passenger side tire will move 1" side to side scarey.Not sure what I need to replace.
View 9 Replies
Have a 06 f350 just rebuilt the engine. Started up ran it down the road a couple miles and lost low side oil pressure. Got back to the house and will not start again so put a gauge on and it only has 3 lbs after cranking for 10-15 sec. Pulled the balancer and lpop cover and front cover had some deeper scoring then before. No noticeable stuff in the pan or filter. Changed out the front cover and lpop. Still has only about 5 psi.
View 3 Replies
I bought this truck a little over a year ago and have put almost 30,000 miles on it. When I bought it, it had a clunk from the front end, but only when I went over a significant bump. It was most pronounced when I, for example, hit a speed bump at an angle and the body rocked back and forth. It's steadily been getting worse and now it's fairly concerning. It happens on pretty much every bump now. Additionally, I've developed a fairly significant shimmy under braking and a vibration over 65mph. I got into a fairly scary shimmy when trying to slow down as I was going down a mountain a few weeks ago.
The other day I started getting a grinding noise from the front right. It goes away when the brakes are pressed. I don't know if the grinding noise and vibration/shimmy are related to the clunking or if they are the result of a separate issue. I have plenty of brake pad and rotor on all corners and there is no perceptible play in any of the front end components (wheel bearings, ball joints, tie rods, shock mounts, etc.). I suspected the leaf spring bushings, but I supported the truck by the frame and still got no noticeable play when jerking things around by hand.
View 14 Replies
I have a E99 F350 7.3L 4x4 I know some or most of you have already probably replaced this part and or pulled a front axle shaft out. So here is my question...In the pictures provided you can see what I think everyone is calling a "Dust Seal" and as you can see it is bad and making a very terrible noise when i hit a bump...I was wondering what parts I would need to replace this seal? I tried looking it up and just get lost in all of the other things....I have found write-ups for the axle being removed while changing ball joints but none by it self to just replace this seal.
[URL] ....
View 14 Replies
2000 Super Duty 2wd. My truck has a lot of slop and wanders down the road. My rotors are also warped and after they get warm they shake like crazy. So I plan on new rotors, bearings, calipers, pads, dust caps and rear rotors, calipers and pads for the rear. I will also be doing factory wheels and new tires and shocks all the way around.
My questions is to rebuild the front suspension and do it to last what all will I need? I see some moog kits but I do not think they are complete for what I need. I only have 126,000 miles with a sound motor and tranny so I feel she is worth it. I know how to work on the truck but the suspension is my weak spot. At 126,000 miles I feel it is a good investment
View 10 Replies
I'm completely aware a lifted truck will not ride factory and most likely ride harder. But this is ridiculous.
So I bought a 8" super lift for my F250 7.3 2000, although the price is very cheap at that shipped to my door debating if I have messed up either with the brand or somewhere because I feel like I went from a casual ride in my lovely 7.3 to feeling like a horse carriage of a few century's ago.
Lift is setup with lift leaf springs in the front, one add a leaf in the rear with a block, and 4 new shocks and all the other hardware included to do the lift.
I'm wondering if it's possible the springs are installed wrong, or the shocks are just that bad or if there a weird issue I've over looked.
Tire pressure is set to 35-40 psi all around on toyo open country mts, (which I was running before the lift so that hasn't changed) but I mean this is so stiff that when I hit a bump my steering wheel jerks and I feel like my suspension has absolutely no flex in it. Debating on returning to stock or not at this point...
View 13 Replies
