In my attempt to remove the auto locking hub on my 2000 F-350 4x4, I found that it would not slide out. I removed the retaing clip and the hub should of be able to come out with a couple wiggles, it seems to have seized inside the hub. I tapped it with a rubber mallet on all sides. Any thoughts as to other alternative methods of removing the hub locker ?
View 14 RepliesMy F350 4x4 won't go into 4 wheel drive unless I get out and take them out of auto and put them in locked position and when I have it in lock mode it seams to work like it's in auto mode, when I put the switch on the dash in 2wd, it seams like it's only driving the back wheels....
View 14 RepliesMy 2010 F350 shudders when turning right. From what I read it could be the auto locking hubs not dis-engaging or sticking in the locked position. Tutorials show it's pretty easy to pull the auto locking Hub out taking out the three screws holding it in place. My questions is what type of grease do I need to apply to the auto locking hub once I have them out and determine that is what the issue is?
View 13 RepliesMy hubs will not lock when put into 4x4. I disconnected all lines from the solenoid to both hubs and tested them for leaks... All good there. I put a gauge on the lines at both hubs one at a time while the other is still connected and get no reading when switched into 4x4. I checked for vacuum right out of the solenoid, and I get 2inHg when switched into 4x.
The vacuum pump kicks on every time I start the truck, even if I just shut it off and re-start right away. There is no delay when switching my ac/heater controls to different settings or vent locations. So I know there is vacuum. How much vacuum I should be getting out of the solenoid to the hubs?
2004 F350 6.0L....
I'm trying to figure out why my auto locking hubs do not engage. To isolate the problem shouldn't the hub engage if a vacuum is applied to that hub only? A solid 18 inHg is maintained at that hub for over 10 minutes but the selector will not rotate, which suggests to me the seals are OK. What then might be the problem?
View 13 RepliesI just replaced the ball joints on my 02 excursion and I can't get the locking hubs to seat far enough in so that the retaining ring keeps them in place. The ring seats but then works out as I'm driving. There is something keeping the hub from sliding in far enough so that the ring/clip can set deep enough in its groove. What's causing that? Its happening on both sides.
View 10 RepliesI took apart, cleaned and lubed my hubs. My question is: how does the vacuum make the gears work?
Does the vacuum force (suck) the nylon assembly to push the outer gear towards the center of the truck, sliding on the inner gear thus engaging the teeth so that the axle shaft turns the hub?
When the vacuum is gone, does spring pressure pushes the outer gear away from the center of the truck thus disengaging the teeth from the inner gear and allowing the hub to free wheel?
Is this vacuum source constant during 4wd and not present during 2wd or do I not understand how the system works? I have read about a “vacuum pulse” that locks the hubs and another pulse that unlocks the hubs and this confuses me.
BTW, I like the way the Auto lock works. I had a set of Warn Auto Lock hubs on my 78 CJ. They worked on the principle of a set of roller bearings that would lock (pinch) when there was torque coming from the drive shaft. There was no vacuum involved at all. The down side was that when you coasted, the front hubs would be in two wheel drive and so you would not get the engine braking on all 4 wheels. These ESOF seem to have solved this problem.
Oh, I should probably tell you that I just purchased my 04 F250 SuperDuty 4x4 with the 6.0 diesel, just had it a week. It has been 18 years since I owned a 4x4. Before this I owned an 87 F250 2wd with the 6.9 diesel.
I have a piece of a warn locking hub that is stuck in the wheel hub. It is stuck in a Ford F-350 super duty SRW 6.8 V10 with a Dana 50 8 lug front axle. Everything seems stock, but we bought this beast late in its life. I have removed the locking hub cap, the inner locking gear, and the metal retaining ring that holds the outer gear in place. The other side just falls apart as it should at this point.
I have tried building a custom puller utilizing the 6 hex cap screws (that attach the locking hub cap) to pull in on two 1/8" thick c channels held off with a 1/2" bolt pushing in the middle of the c channels on the axle. In one case, I sheared off the bolt, and bent the c channels. I tried it again and that time broke several of the hex cap screws off.
I have ran through penetrating oil, wd-40, propane (for a torch) and carb and brake cleaner as I tried heating up the hub while applying penetrating oil and letting things sit, then spraying out rust and such with carb or brake cleaner to loosen things up, then repeating the process over and over again. I have done this process several times. It worked on the center where the axle goes through the inner gear, so now the inner gear is now loose from the axle. But the outside is still suck like no other.
Lightly hitting on it with a 3lb sledge to crack something lose has done nothing, and left me struggling not to beat it much harder with a bigger hammer with a longer handle.
As a note, it took weeks to get the center locking gear to fall out after doing the oil, heat, and spray cleaner process, then driving with it locked in, and it took two attempts and hours to get the cap off from stuck hex cap screws, several which I had to drill out in the end after even an impact screw driver would not work. The U-Joint is bad, and I can't lock in the 4WD which is problematic at the dump and on job sites when it is muddy especially when we are towing a maxed out 5k single axle trailer that wants to dig in to the mud too.
I have a 2013 F250 which has both the Manual and auto locking hub feature. I tried to plow my driveway this morning and after making one pass I put the truck in reverse and could not back up my steep driveway. The truck is showing locked in 4x4 on the dash, the 4x4 control is in high lock but the front wheels will not turn. It has been very cold here lately (-30) and I'm wondering if the vacuum lines for the auto locking hubs have frozen. I have switched the control out of 4x4 and back in several times, and it does lock in again, but as soon as I put the truck into reverse, they unlock again. The hubs are covered with ice and snow right now so I have not yet tried to manually lock them.
View 14 RepliesOn my 05 350, I noticed the other day that my 4wd wasn't working, when I needed it of course. I quick test this morning and I discovered my PS hub is not locking in. I've read a lot of posts about it being the opposite, the auto portion causing a problem. In my case, it won't lock in in auto or manually turning. I can lock it in, spin the wheel and the axle shaft isn't turning. The pressure is the same as the other side, not too loose or too stiff. Can I pull the hub assembly off and rebuild it? I watched a video about that, but not sure on how my issue would allow me to work on it.
View 4 RepliesI drove my pickup on mostly dry pavement the other day with it in 4WD and the hubs locked. I got a bit of shimmy/vibration which quit after about a mile. When I got back on ice, the 4WD wasn't working. I assumed the transfer case or locking hubs had failed. Today I got it up on jack stands, put it in 4WD, and locked the hubs. Everything seems fine. What might have happened when I couldn't get 4WD to function.
View 2 RepliesI have the dreaded flashing O/D light on my early 99 F350 7.3 4x4 auto. The only one's that seem to be consistently recommended are Snap-On or AutoEnginuity.
View 1 RepliesSo I have an 05 f350 5.4 with the shift on the fly and the auto/manual locking hubs.. I already know I have a leak with the vacuum and I just use the hubs manually, then shift on the fly to activate the transfer case.
I went to use the 4wd the other night in a snow storm and I have no 4wd, light on the dash comes on and i can hear the transfer case clicking in when i hit the switch between 2wd and 4wd.
So I got under the truck while it was on the ground and manually locked the passenger side, Then tried spinning the axle and it wont spin freely, so obviously its locked.
Tried the same thing on the driver side and the axle spins freely while the hub is locked, So obviously the locking part of the hub is no good... So i guess my question is, even with just 1 wheel locking in the front, shouldn't I pretty much get 3wd? or am i missing something...will it not engage at all because both sides arent locked?
Putting in a locking axle to replace there non locking axle? Have a 2015 f350. And found a electric locking for a great price. Can this swap be done?
View 14 RepliesI was using 4x4 High the other day and it was working just fine. Now today, I was at my first parking lot to plow and used the ESOF to shift into 4x4 High and it did not engage with the hubs being in auto mode. The lights on the dash show up indicating that I am, but I am still in 2wd.
If I manually lock the hubs, it engages 4wd high. I tried the same thing using the ESOF to switch over to 4x4 low and it does NOT engage either.
I also noticed that heater blower was switching over to full defrost even though I had it set on the floor setting (manual heat climate *****).
Does this sound like a vacuum leak? I haven't had a chance to test the lines yet. Btw, this is my second work truck and not the one listed in my signature below. It's a 2006 f-350 6.0 xlt.
I have 2014 F350, was previous flood damaged, the steering keep sticking when I turn it to the left, not always in the same spot, but sometimes it just locks and will not turn right, needs lots of jiggling and then it release, as I say in different places but always when turning to the left, never when turning to the right. Does this indicate steering gear fault or something else?
View 9 RepliesI have a 'new to me' 2007 F-350SD super cab and need to run some wiring inside. What I don't know is how the heck the trim pieces are attached and how to remove them without breaking them! If it ain't held on with screws, nuts, bolts...
View 2 Replies2008 F350 hubs wont stay locked in when in auto position. everything stays locked while in manual and 4x4 works fine, but in auto the hubs wont stay locked while spinning. I was trying to find the problem when i noticed that one hub stays locked all the time and the other locks and unlocks as it should but it wont stay locked while spinning. My question is do I have two bad hubs or is their a leak that wont let the hub stay locked? Also on the hub that wont unlock is this a leak problem as well or a internal problem?
View 5 RepliesWent to change the plugs on an 02 f350, the bolt holding the plug wire boot on doesn't seem to fit any standard size socket. 7 is too big, 6 is too small. 1/4 is too small, 9/32 is too big.
View 14 Replies2002 F350 5.4 . I did some plowing today, truck ran Great, but noticed the Auto Shifter starting to get some play in it, 185 k on it. I recall reading about how to tighten it back up.
View 3 Replies2005 Ford 350. I want to change the ball joints on the front axel and I cant remove the axle out of dif. to remove the ball joint housing. I have been prying and pulling and it just moves out a 1/4 inch or so .They tell me there is no ring to remove in dif before you can pull it out but why this trouble?
View 4 Replies