I have a 2000 f 250 that will not start... I have replaced many parts all electronic sensorsm the past week i have spent in the neighborhood of 1800.00 on this truck. Cps, icp, idm, ebps, fuel filter, new oil, hpop level good, gpr, all new need starting........
View 4 RepliesI just bought a 2000 F250 SD, 4x4, 5.4, Quad Cab. I drove it off the lot, stopped to put air in the tires, jumped back in and it wouldn't crank. All of the dash lights worked fine. Tried jumping at the starter solenoid and got nothing. Got under the truck and jumped it off the starter, vroom, fired right up. Replaced the starter solenoid and had no issues for about 2 hours. Then it did it again. This time it wouldn't start at all. I towed it back to the dealer and they had it for 3 weeks.
Then yesterday I called and they said it was done. Picked it up, drove to the barber shop, got my hair cut, came back out and it did the same thing AGAIN. After jacking around with the shifter and turning the wheel back and forth 100 times it started. The key is kind of hard to turn sometimes in the ignition, so I'm thinking that the ignition cylinder needs to be lubed real good, but that shouldn't stop it from cranking the motor over, right? I was going to swap out the ignition switch, but I don't know if that will do any good either.
My 2000 F-250 V10 won't start has a new alternator and new starter all it does is Click when I turn the key?
View 14 Replies2000 f250 V10 ...
Problem: More often than not when the key is turned to run (?), prior to engaging the starter, the fuel pump does not turn on for its 5 seconds. I have installed a fuel pressure tester gauge to watch the fuel line pressure. It was a little shaky to diagnose because if the line had pressure/fuel from the previous run it will start and run a short time and then die from lack of fuel. Unless the fuel pump activates when the key is turned to run, prior to full start, then there will be no fuel coming from the pump. No start. If you work the key to run a few times until the pump engages its good to go. The truck has never died while driving, once it gets that initial pump activation it runs good until the next start up cycle. When the pump does work it builds up to good "book" pressure and holds it at 39 when the engine is shut off.
We have put off changing the fuel pump for obvious reasons but can not see how it could be the problem since it has never quit once after we get it started. Are we wrong? We know the fuel shut off is on as it will run. We have changed the key lock tumblers, the ignition switch and the fuel pump relay. (behind the radio). Next up is to re-seat all the fuses and relays in the main fuse panel box under the hood. I just read that today on FTE. Is there a test we can do or some engine codes we need to look for? This problem is getting old fast.
My 2000 F-250 6.8L V10 has a choppy idle during the first 30 or so seconds after a cold start up in the morning then it smooths out and drives perfectly. If I were to place the truck in gear during the choppy idle, it would not die and throttle response would be fine.
I cleaned the MAF sensor and checked the PCV elbow for cracks (no cracks). It idles at about a 1000 rpm during a cold startup then drops to about 750 rpm according to the dash tachometer. The truck has 187,000 miles on it.
I have a super duty with the 5.4 in it. it just quit while off road n wouldn't start back up. pulled it back to camp, wiggled wires around cam n crank sensors n it fired up n stalled numerous times then just wouldn't even fire back up. loaded on trailer n brought home, buddy put his tester on there n said there was no rpm reading so I replaced the crank sensor, it fired up n stalls still. wires seem to be good to crank n cam sensors. don't have a manual to tell me what relays are what.
View 11 RepliesI recently caught up on some maintenance with my truck, changed the turbo pedestal seals, replaced both batteries, brakes, e-brake cable etc and installed new 10k hid headlights. its a single cab 250 with a 7.3 and zf6 4x4 with 133k. a couple days ago I turned on the headlights and the truck died, restarted no problem and would die the next 5 times I tried to turn them on, then it worked fine. yesterday I got in my truck to leave for work and got no wait to start light, no glow plug chatter, no fuel pump running. turns over just fine but no fire.
I got a ride to work and tried it when I got home, fired right up. I pulled the pCM, checked it out, no weird smells and my TS chip wasn't corroded or anything like that, worked fine. drove to 711 to get a 6 pack and it did the headlight thing again. I removed the HIDs because this all started after I installed them and reinstalled my silvanias and it didn't die when I turned them on. this morning went to leave for work, same no start condition. I disconnected both batteries for 30 seconds to reset anything and same problem. I was about ready to light it on fire this morning.
I have a 2000 f250, 5.4l triton v8 that cranks like crazy, but won't start. When I spray a little starter fluid in it it will run until the spray wears off. Brand new battery and full gas tank. it does have check engine light on dash, probably from the o2 sensor as the exhaust has almost completely rusted out. Also on a side note the cruise control will not engage.
View 6 Replies2000 f250 7.3. Today I tried using the 4x4 and no light or anything. Here is what i have tried so far. Swapped the relays and also swapped them with the towing relays with no change. Not getting any voltage to the t-case shift motor at the selector switch testing between pins 2 and 3 there is 4.3 volts with switch in 2wd 2.4 volts at 4 high and 1.09 volts at 4 low. Where to go from here? it worked fine 3 days ago.
View 2 Repliesmy 00 f250 has the air bag light on all the time. it does not flash it just stays solid. it was like this when i bought the truck @3 months ago. also the passenger air bag switch does not light up when you use it. is this causing my airbag light to stay on?
View 9 RepliesI just bought the truck and the ac was working and now out of nowhere when you turn it on it just blows hot air so I just assumed it was out of free on so I bought an ac pro but that did nothing.
View 5 RepliesI have a 2000 F-250 V10 that misses (cylinder 10) at the idle, once you give it gas it runs correctly again. I am at a loss. I have replaced the plug, tried moving coils from one cylinder to another to see if it shifts the miss, and it has new injectors. What this could be?
View 9 RepliesSo a few week back I noticed my brakes were getting soft. Soft meaning that when braking for any distance, I would hear a kind of "pressure release, squeaking" sound coming from the pedal, and the pedal would sometimes go to the floor and the ABS would kick in. Let me tell ya, its a pretty crappy feeling when your brakes aren't doing what their supposed to! So, I replaced the pads all the way around, replaced the master cylinder (bench primed). I took it out for a drive, and it did the same thing. So thinking maybe the fluid is bad, I flushed new fluid through the lines. Took it for a drive, and it felt good right away, the pedal firmed up a bit, and then it did did it again.
Just so I give as much info as possible, the rotors are looking pretty rough and going to be replaced soon.
So, my question[s] are; What is the next step in identifying the problem? Is there a chance the new master cylinder is bad? Could worn rotors cause the caliper to max out and not apply enough pressure? Even though the calipers seemed fine while replacing the pads, could one or more be bad? If so, how do I know?
I have a 2000 ford f250 5.4 2v that's been having a shaking at idle and no power what so ever. I tried diagnosing it myself and came up with nothing. I finally decided to take it to the dealer and they are telling me that the right side has no compression on 3 cylinders. They want almost 7000 for a new engine. I was wondering if it was possible to get away with just putting a new head on the right side?
View 13 RepliesI have a f250 with 6.8l engine. I can get air thru the defrost and to the floor, but no air thru the dash vents on me. I have traced all vacuum lines and they seem fine.
View 1 RepliesDoes it need a diesel fuel injector?
View 2 RepliesI have a 2000 F250 SD with the V10 engine. The problem that I am having with it as of late is that whenever I perform a full turn I hear some clunking coming from the front end. The clunking is similar to that heard from cars that use CV joints FWD but of course it sound more "manly"
Anyways, my truck has the full axle on front so I suppose it could be either the u-joint at the hub or the hub itself. I would like some pointers so I can acquire the required parts.
We have a 2000 F250 7.3L Diesel. A few years ago we switched out the auto hubs for manual Warn hubs. We've had no problems with 4x4 since that time, until now!! The 4x4 Hi light is on and the transfer case is engaged. Since the hubs are manual we have them unlocked, however we can't get the 4x4 to disengage. At one point, tried changing to low and it hesitated but finally went in to 4 Lo, then we had a hard time getting it out of 4Lo and back to 4 Hi. Here's what we've tried--checked fuses, checked and replaced relays, checked wiring connection at the transfer case. Husband used volt meter to test power at transfer case wiring connector--showed 0.5 volt of power with the key on. No change in reading. Checked power at relay--about 14.5 volts there. Took truck to repair shop but their computer could not communicate with the GEM.
View 7 RepliesI recently purchased a 00 F250 psd 4x4. Other than doing all of the fixes it needs to make it ride better I have been questioning the trucks "get up and go" and the EXTREMELY sensitive skinny pedal. Truck seems to pull very hard and puts out some black smoke under hard throttle but nothing like the really tuned trucks I have seen. But the skinny is so sensitive its hard to drive under 40mph in 3rd and once it gets up to 55 or so its real sharp getting on and off the throttle. Trans shifts great, TC locks and unlocks, truck runs awesome IMO but just a bit harsh. Is there a way to find out if it was tuned prior to me buying it other than inspecting for a chip, or is this the way they are and I just have to get used to it more...?
View 9 RepliesI am scared. The cooling fluid of my 2000 F-250 is brownish. I am not sure if it is Oil, which would be bad. Is there a way that I can find out what it is? I'd like to get an opinion of my own before I take it to a repair shop.
View 11 Replies2000 F250 Super Duty cruise control not working. I looked through a lot of threads on this subject and cannot pin point my problem. Cruise control was working, had to slow down wile approaching a town, back on the highway and now it won't turn on.
Looked at the brake pressure switch, it was till good but was the old type but had the recall harness on it. Bought a new one and replaced it anyways. Still nothing. All my brake lights work, I also did the Cruise control diagnostic and it passes everything. No lights on my dash are on, speedometer works, horn works.
The only thing I did not check is the Vehicle speed sensor. Even though my speedometer works and my ABS light is not on, can this still be the problem? If so how do you test it? Do I just remove it and test continuity?