Ford Super Duty (1999-2016) :: 2000 F250 V10 - Random No Fuel Pressure At Start Up
Dec 21, 2015
2000 f250 V10 ...
Problem: More often than not when the key is turned to run (?), prior to engaging the starter, the fuel pump does not turn on for its 5 seconds. I have installed a fuel pressure tester gauge to watch the fuel line pressure. It was a little shaky to diagnose because if the line had pressure/fuel from the previous run it will start and run a short time and then die from lack of fuel. Unless the fuel pump activates when the key is turned to run, prior to full start, then there will be no fuel coming from the pump. No start. If you work the key to run a few times until the pump engages its good to go. The truck has never died while driving, once it gets that initial pump activation it runs good until the next start up cycle. When the pump does work it builds up to good "book" pressure and holds it at 39 when the engine is shut off.
We have put off changing the fuel pump for obvious reasons but can not see how it could be the problem since it has never quit once after we get it started. Are we wrong? We know the fuel shut off is on as it will run. We have changed the key lock tumblers, the ignition switch and the fuel pump relay. (behind the radio). Next up is to re-seat all the fuses and relays in the main fuse panel box under the hood. I just read that today on FTE. Is there a test we can do or some engine codes we need to look for? This problem is getting old fast.
View 7 Replies
Advertisement
I have a 2001 F-250 XLT 4x4 with V10. Truck will not start. No fuel pressure. My Haynes manual does not show ignition or fuel delivery wiring. I have found the relay box behind the radio/dash. I need a wiring diagram and info on which relay is the fuel pump relay. Want to know so I can jump relay to see if fuel pump is okay.
Truck had sat for a few weeks being ran very little, so had to jump start yesterday. Ran for about 15 min, the shut off, re-started and ran for 30 min. Truck sat for about 1.5 hours then would not start. Charged battery overnight and it is 100%.
View 3 Replies
I have an 02 250 5.4. 103,000 miles. My truck at random times will not start in below freezing temps. Turns over just fine but Acts as if a frozen fuel line. I can get it running by pouring hot water on the fuel rail or a shot of starting fluid or sometimes both. It's been going on about 3 or 4 weeks now and I have ran through 4 bottles of dry gas with about 15 gallons each time. Also have replaced fuel filter and fuel pressure regulator. I'm 99.9% positive the pump is working and there are no leaks in the lines or holes in tank that I can see. My next step is to drop the tank and clean it out but trying to avoid that.
View 14 Replies
I have a 2010 f250 6.4 About two months ago the truck just quite on me. I am a farmer in south jersey and have a decent background in diesel motors. First thing that came to mind was fuel. I assumed I was having a fuel issue (clogged filters, failed pump, etc.) truck only had 45,000 miles on it so I took it to my local dealership for what I assumed would be a warranty job. I dealer service all my trucks while under warranty. Long story short I was told it was a fuel contamination issue which scared the walls of the hpfp throwing metal pieces into the injectors, fouling them.
I would need all new injectors, fuel rails etc. as well as new filter housings, fuel tank cleaning, etc. I had receipts for every drop of fuel put in the vehicle and fought all the way to through the dealership to Ford who sent out a rep and who denied the warranty work. Fortunately my insurance company covered the ordeal and all repairs were completed. I got the truck back and 2 weeks later the truck died on me again. I called the dealership back who supposedly warranted the repairs but there first words were there is no way it is their problem, they would look at it but I have to consent that if they find it is contamination again I am responsible for the repairs which we all know just to diagnose they have to remove the cab etc.
I of course lost my mind and told them this is there issue and there is no way in hell I am that unlucky that I received 2 bad tanks of fuel from 2 different high volume highway side fuel stations in the same 2 months. it is obvious they missed something or there is another issue that was not addressed. They claim there is no way they missed something. I am at a standstill.
View 4 Replies
Started truck it ran about 10 sec. then quit, low oil pressure came up on the dash will not start now.
View 2 Replies
I have a 2000 f 250 that will not start... I have replaced many parts all electronic sensorsm the past week i have spent in the neighborhood of 1800.00 on this truck. Cps, icp, idm, ebps, fuel filter, new oil, hpop level good, gpr, all new need starting........
View 4 Replies
I have a 2000 f250 V10 CC 4x4 long bed. The rubber fuel line that has a quick disconnect to attach to the fuel filter along frame is leaking. This is on the filter side going to engine. Ford tells me fuel line not available. Dorman products tech assist can't tell me which connector of there's will fit my truck.
View 2 Replies
I just bought a 2000 F250 SD, 4x4, 5.4, Quad Cab. I drove it off the lot, stopped to put air in the tires, jumped back in and it wouldn't crank. All of the dash lights worked fine. Tried jumping at the starter solenoid and got nothing. Got under the truck and jumped it off the starter, vroom, fired right up. Replaced the starter solenoid and had no issues for about 2 hours. Then it did it again. This time it wouldn't start at all. I towed it back to the dealer and they had it for 3 weeks.
Then yesterday I called and they said it was done. Picked it up, drove to the barber shop, got my hair cut, came back out and it did the same thing AGAIN. After jacking around with the shifter and turning the wheel back and forth 100 times it started. The key is kind of hard to turn sometimes in the ignition, so I'm thinking that the ignition cylinder needs to be lubed real good, but that shouldn't stop it from cranking the motor over, right? I was going to swap out the ignition switch, but I don't know if that will do any good either.
View 3 Replies
My 2000 F-250 V10 won't start has a new alternator and new starter all it does is Click when I turn the key?
View 14 Replies
my 2014 low fuel light comes on at random milage some times 27, 23 19 no set time it is a diesel dealer says its normal ?
View 1 Replies
I see several threads regarding engines that wont start for no apparent reason. My reason was a failed fuel pump relay. This sucker is hidden in the dash below and to the left of the radio. I got to it by taking out the ash tray. There are three relays under the cover. The upper left is the fuel pump relay. The one to the right is the turn signal relay. I don't know what the bottom left is for.
View 3 Replies
My 2000 F-250 6.8L V10 has a choppy idle during the first 30 or so seconds after a cold start up in the morning then it smooths out and drives perfectly. If I were to place the truck in gear during the choppy idle, it would not die and throttle response would be fine.
I cleaned the MAF sensor and checked the PCV elbow for cracks (no cracks). It idles at about a 1000 rpm during a cold startup then drops to about 750 rpm according to the dash tachometer. The truck has 187,000 miles on it.
View 4 Replies
I have a super duty with the 5.4 in it. it just quit while off road n wouldn't start back up. pulled it back to camp, wiggled wires around cam n crank sensors n it fired up n stalled numerous times then just wouldn't even fire back up. loaded on trailer n brought home, buddy put his tester on there n said there was no rpm reading so I replaced the crank sensor, it fired up n stalls still. wires seem to be good to crank n cam sensors. don't have a manual to tell me what relays are what.
View 11 Replies
I recently caught up on some maintenance with my truck, changed the turbo pedestal seals, replaced both batteries, brakes, e-brake cable etc and installed new 10k hid headlights. its a single cab 250 with a 7.3 and zf6 4x4 with 133k. a couple days ago I turned on the headlights and the truck died, restarted no problem and would die the next 5 times I tried to turn them on, then it worked fine. yesterday I got in my truck to leave for work and got no wait to start light, no glow plug chatter, no fuel pump running. turns over just fine but no fire.
I got a ride to work and tried it when I got home, fired right up. I pulled the pCM, checked it out, no weird smells and my TS chip wasn't corroded or anything like that, worked fine. drove to 711 to get a 6 pack and it did the headlight thing again. I removed the HIDs because this all started after I installed them and reinstalled my silvanias and it didn't die when I turned them on. this morning went to leave for work, same no start condition. I disconnected both batteries for 30 seconds to reset anything and same problem. I was about ready to light it on fire this morning.
View 1 Replies
I have a 2000 f250, 5.4l triton v8 that cranks like crazy, but won't start. When I spray a little starter fluid in it it will run until the spray wears off. Brand new battery and full gas tank. it does have check engine light on dash, probably from the o2 sensor as the exhaust has almost completely rusted out. Also on a side note the cruise control will not engage.
View 6 Replies
Truck Specs:
2008 f250 super duty 5.4l
78xxx miles
4x4
Automatic
Issue:
P0300 (random misfire detected)
P0307 (cylinder 7 misfire)
Let's start from the beginning...
I was getting the notorious 5.4l ticking sound. After doing research on this issue. I found that it could be a few different issues including:
Cam Phasers
VCT solenoid(s)
Loud injectors
Valves
Exhaust leak
Loose spark plug
The list could possibly go on, but these being top concerns or issues to look into.
I took it to my mechanic and wanted him to research the ticking problem. This was my primary concern due to it was getting worse over time. I didn't want to do more damage than what was possibly already done. I told him to go ahead and change the spark plugs while you're checking into what's going on. (I know those plugs can break and I didn't want to do that.)
At any rate... the plugs got changed to motocraft brand (I know the trucks can be finicky with the parts you put back into them so I went with the motocrafts to avoid any complications.) After the plugs were changed, he told me that the ticking was caused from a blown exhaust manifold gasket (yay me... not internal parts or anything too serious. Sweet!)
I had to reschedule to get the gasket done, but knowing what it was now I wasn't too concerned about driving it. So I did. The new plugs are also in the truck at this time. I drove it the next day and right away.. I noticed a misfire. Thought maybe the plug was bad. I told my mechanic about it and he said... Sounds like a COP to me.
So I get a new COP. Okay.. easy fix. Installed it and still got a misfire. Told my mechanic and he said get another COP. So I'm thinking.. "Okay.. get a new part to fix a new part.. sounds logical.. lol" so I do what he thinks might be best. I replace the COP with another new one and it's still misfiring. The new cops are also motocraft brand as well.
Okay... next step.. he claims it may be a VCT solenoid issue. At this point I don't care.. I just want my truck fixed. So he replaces the driver side solenoid. Still misfiring..
So after doing some research on the scanner... we locate some issues that are the exact symptoms I'm having. Misfire.. at low rpm.. during cruise control.. and a sudden at idle.
This information states for this drivability issue.. to spray injector cleaner/carb cleaner into the engine and possibly clean it out. Makes sense. He did this as well as changed the fuel filter. Also did a pressure test on the injectors to make sure they were good. They were. After spraying and cleaning it out, it was taken for a test drive and it seemed okay... but not perfect. The next day.. the misfire came back.
He said that if the misfire returns, that I need to contact the dealership and see if there is a pcm update. The dealership said there probably is but can't tell me until the computer is hooked up to it. (Of course there is a charge when it's hooked up) again.. whatever.. I just want it fixed. The truck is scheduled to go in next Wednesday for that. If that doesn't fix it, my mechanic said cam phasers possibly bUT still not sure for sure..
View 3 Replies
I had my fuel filters changed at the dealership today on my '15, and then I bought fuel and headed home (70 miles). About half way home I got a "Low Fuel Pressure" message and a little while after that "Reduced Engine Power" along with the check engine light.
I pulled over to see if they did something like leave the drain open, thinking it might be sucking air. Of course it was dark and I could not see anything. However I did hear a buzzing sound and could feel a vibration when I touched the fuel line going into the top of engine filter.
While it is possible I got bad fuel, I suspect they did something wrong installing the filters. Even after cycling the fuel pump multiple times they had a hard time getting it started afterwards; I think they finally disconnected the top fuel line to bleed the air out.
I continued home and made it, but not sure what to do now; its 70 miles back to the dealer.
What is the most likely problem? Improper fuel filter installation or bad fuel?
Should I pull the filters in the morning see if there is something obvious like an out-of-place gasket? If so, top or bottom filter?
Is this a tow truck affair or should I drive 70 miles back to the dealer?
What the heck is the buzzing sound?
View 7 Replies
So the first issue is, if the vehicle is cold (regardless of temp outside) it takes forever to start it. It cranks and cranks and cranks and after a couple seconds of cranking I stop, wait a second, then try again. Usually it takes two sometimes three tries to start it. The guy who I bought it off of said it has newer glow plugs (last year I believe) and also I have replaced the batteries. Once its warmed up it does not do this at all.
Secondly and also something that just recently started happening, my water in fuel light keeps kicking in. I drained the water out of the water catcher reservoir under the truck multiple times and the first time water actually came out but every time after that simply diesel fuel comes out. I added a bottle of water remover to the fuel as well and ran it down to a quarter tank. Then filled the truck up completely, added two more bottles of water remover. The light still comes on. I noticed it only comes on when I am going up or down a fill. When I am driving on flat ground it does not kick on.
View 4 Replies
Changing a fuel pressure regulator on one of these? I'm having an issue with it running really lean, like laying down with no power lean.I put the pressure gauge on it and I'm running an even 30 pounds at the rail. Changed the filter in hopes, but no change. Just changed the O2 sensors and they were both white.
View 9 Replies
I have a 2001 Ford F250 V10 with about 70,000 miles on it and now the gauge indicates low pressure when my warmed up truck idles around 1000 RPM.
I went off road the other day into some mud and since then I have had my oil pressure gauge reporting low at idle and normal when moving.
I was a quart and 1/2 low on oil which I filled and the next day I changed the oil. I then had taken it Ford shop who replaced the oil sensor and said all fixed. It wasn't and I took it back in ... now the mechanic indicated it is probably the crankshaft bearing based on his experience and I should replace the engine.
This seems drastic? Wouldnt' the next step to go check/replace the oil pump?
View 6 Replies
I have a few F-250's that have been having steering problems. and they all have the same symptoms.
When taking a long slow curve, the steering wheel will jump back like 6 inches, as if the pressure is going out. like say you had the vehicle turned to about 10 oclock, the wheel would go back and forth between 10 and 11. However, you do not loose much of your turning. It just has more pressure against your hand as if the power steering goes out.
You can also do it a standing stop. Only when you turn your wheel like say to 9, you can just use a finger to hold it there and it will bounce up and down? I have asked the local Dealership, and their answer was "there is something wrong with the power steering." couldn't get much more vague than that I guess.
I have looked for leaks, none. Checked struts, not bent. Checked tires, all brand new and balanced. Checked steering wheel mounts, all good to go... ???? Just lost...
View 2 Replies
