Ford Super Duty (1999-2016) :: 2000 F250 - Sloppy Steering And Noise In Front End When Going Over Bumps
Jan 3, 2015
My 2000 f250 7.3 has pretty sloppy steering and noise in the front end when going over bumps. I have replace the drop links, swap bar bushings, both wheel hubs including new seals and the drag link. The rest of the front end seems to be in good shape. I put it up on jack stands and there is some movement in the front end but it seems to all be in the steering box.
Steering box appears to be original with 220k miles. I went to tighten it and it appears the PO did it at least once already. Is it safe to try tightening it again? Does tightening it increase the risk of failure? I'd like to try tightening it first but not at the risk of losing steering at 65mph with my kids in the truck.
View 14 Replies
Advertisement
I bought a 2000 F250 V10 Super Cab. Oddly after a few weeks it has grown on me. There has been a clunking noise out of the right front over bumps. I traced it to a bad axle bearing. The u joint moves up and down about a 1/2 inch. Besides pulling the hub/bearing assembly out and removing the axle are there any surprises getting the old bearing out?
View 1 Replies
just bought this f250 seems to walk on the road alot, had it looked at has new balljoints, he says everything seems tight except there is lots of play at the gearbox, is it recommended to have it rebuilt or buy a reman, was told that even the reman seems to be the same way
View 14 Replies
I have a 2000 F250 2wd 6spd with a loud banging noise that has been vexing me for quite sometime now. The bang happens when I go over bumps (even small ones like road reflectors) while driving. I don't think it is suspension related since all the ball joints, front/rear swaybar and endlink bushings have been replaced fairly recently. All the springs and bushings also look okay.
The noise seems to come from the rear, and I notice that if I let off the gas when I go over a bump, it does not make a sound. Conversely, if I am accelerating aggressively and hit a bump, the sound is much louder. Also, if I step on the clutch while keeping my foot steady on the gas, it makes a bang. Jumping up and down in the bed while the truck is parked does not recreate the sound. I have already greased the driveshaft spline joint so I'm thinking the sound might be differential or transmission related. What it could be?
View 9 Replies
2002 F-250 7.3 4x4 ...
I have a rattling noise coming from the front suspension (both sides) when going over small bumps. Most people point to ball joints, but I find my case odd because I just replaced
Upper/Lower ball joints
Track bar
Tie rod ends
Shocks
Front U joints
Drag link
I did not touch the leaf springs or the sway bar, except to grease the links, which otherwise looked good.
View 3 Replies
When I go over good size bumps, I hear a clunk in the front tire area when my driver's window is down. It's a metal noise, like something loose.
2011 F-250 with 203K miles. Replaced shocks last year. Did this with stock wheels/tires. Something in the front suspension or axles. What should I be looking at?
View 8 Replies
I replaced my steering gearbox with a remanufactured oem gearbox (no, not the redhead. I wish I'd had the extra money but I didn't.) I replaced the factory sway bar (1.25" diameter) with the Excursion sway bar that came on my axle (1.4" diameter) along with polyurethane bushings and greaseable end links. I replaced wheel bearings, ball joints, track bar bushings, tierods (ends, sleeves, the whole nine yards). Literally everything from the gearbox down, besides the pitman arm, is brand new.
The next day I took it in and got it aligned at Goodyear. The steering is noticeably more responsive, but I still have 1-2" of play either way before I get a response. I'm skeptical about tightening the gearbox. I did that on the old one and it improved steering for a couple years, but this new one shouldn't require any tightening.
I have yet to install new steering stabilizers, but I can recognize bump steer versus this problem on a straight, smooth road. I'm sure the stabilizers won't change the 2 inches of play.
View 13 Replies
I have a noise with my new (2.6k miles) 2000 Diesel F250 Crew Cab. When I make low speed, right turns while crossing any type of depression in the road I hear a loud knock as if the left shock is bottoming out. There's an intersection near my house with runoff depressions across the road, I almost always hear the noise when making that turn. I've occasionally heard it coming from the right side when making a left turn.
View 14 Replies
My 2013 f350 long bed diesel pickup has a noise in the front end when going over a bump such as a curb at low speed. It will also occur if turning onto a side street that is at a downhill grade. The vehicle has 4000 miles and is just at one year old. The noise sounds like a shock housing scraping on the shock or a very dry and rusty bushing. It also sounds similar to the anti-lock pulsing. I have had it to the dealer twice and they can not find a problem. The noise is very loud and easy to hear. I have gotten under the truck and looked around to see if I can find any evidence of rust and do not. Sometimes if I have my foot on the brake pedal when the noise happens I feel the anti-lock pulsing.
View 7 Replies
I have 2004 Super Duty with a noise in the front end when I hit bumps or backing out or entering a driveway with a lip. I don't feel anything in the steering wheel but I feel it on the floor board with my feet? Where to begin?
View 3 Replies
My 2000 F250 4 x 4 just started being almost impossible to steer to right when stopped. To the left it is ok. I was on a trip and when I got where I was going noticed the steering very hard. I checked the fluid level and it was almost empty. I filled the reservoir and let it sit 4 days. I am back on the road now and it is still doing it. Stopped to left is easy to right almost impossible.
My brakes are good. I noticed a couple times when I had to slam on the brakes on the tirp the rear tires chirped. I don't tow anything with it, just a family vehicle with 408000 miles. The power steering pump was replaced a few years ago. Pump, gearbox, etc? I need to get this fixed as I have another trip coming up in a few days.
View 2 Replies
Any link on how to do a flush on the 5.4L power steering pump? I screwed up on installing my new power steering pump and used power steering fluid (new to ford) and it is moaning so I need to flush and get mercon ATF put back in the lines. The write up I found was for the diesel hydroboost and I do not have that setup.
View 3 Replies
I need to know what the name of the part is that the front shock mounts to on my 2000 f250. Its terribly rusted on both sides and id like to learn more about replacing it. Might me called a shock mount? It saddles around the main frame on the truck.
View 3 Replies
As the title says are my front leaf springs bad? I got this truck 2 years ago and replaced all the ball joints, shocks, sway bar links,front hubs, rotors and brakes along with all the seals. I have a clunk in the front and I can't figure out what it's coming from. Could my leaf springs be clacking together? Truck
is a 2000 F250 SD v10.....
Driverside front
Rear spring
View 10 Replies
I have a 02 F250 4x4 5.4. As I drive and when pulling into a driveway I hear a clunk that can be felt in the floor and the steering wheel. I've replaced the wheel bearings and seals, shocks, ball joints, sway bar links and bushings, tie rod ends at the gear box and "right hand inner". The other two tie rods are tight and so is the track bar. I cannot duplicate the sound if I jack it up and move parts around with a pry bar. I can however move the steer box sector shaft upwards about an 1/8. I've adjusted the screw but it didn't do anything. Could it be the steer box or the springs? I've even mounted a GoPro underneath but everything moves and I can't tell why it is.
View 14 Replies
I have a 2000 f250 4x4 with 4 wheel abs. The front passenger side caliper keeps locking up while I'm driving and won't release and when I hit the brakes it pulls hard to the drivers side. I have put two calipers on the passengers side and put new brake lines on.
View 8 Replies
Well, I've been meaning to get to servicing/re-greasing the front hubs/bearings for a while but somehow it keeps getting moved down the list.
2000 F250SD 4X4 Gas Manual Hubs+Trans
I'm currently going through the many threads that turned up in my search query.
Driving slow with the windows down it seems like a low whine or squeal coming from the left front. Tone changes when working the steering wheel left and right. Haven't detected any grinding sounds. Any other techniques for isolating the problem? It's going up on jack stands tonight and I'm going to see if there is any wobble from the front wheels and I'll listen as I turn each of the front wheels. Oddly, the right front hub is hard to turn. Left front turns easy.
Viewed Rob259956's videos on servicing the hubs. Currently researching accessing the wheel bearings. It seems pretty straightforward. Truck has been off road but not mud bogged or anything like that. I'm guessing a bad bearing will be easy to identify as will a bad o-ring but any other stuff I should look closely at?
View 6 Replies
I have a 2000 f250 with auto/manual locking hubs and today the 4x4 quit working. The light comes on the dash and the drive shaft and u joints turn but the front wheels don't turn even when its locked in. I assume its the hubs? And when I am going down the highway about 75 the front starts making a hellacious noise but stops if I slow down is this connected?
View 11 Replies
The other day I was under my truck and noticed electrical plugs behind the front splash guards. What these might be for? I have a 00 F250 superduty XL model with the 5.4.
View 8 Replies
I have a 2000 F250 SD with the V10 engine. The problem that I am having with it as of late is that whenever I perform a full turn I hear some clunking coming from the front end. The clunking is similar to that heard from cars that use CV joints FWD but of course it sound more "manly"
Anyways, my truck has the full axle on front so I suppose it could be either the u-joint at the hub or the hub itself. I would like some pointers so I can acquire the required parts.
View 14 Replies
So, yesterday when I got home I stopped at the barn to unload a few bails of hay and when I got back in to crank it, nothing happened. I turned the key and nothing, so I figured I would just worry about it today. However, when I turned the key back to off and started to take it out all sorts of stuff started to happen. There was a clicking noise and a dinging, not like when the door is open. It was quicker. Also, when I turned my key back on none of my dash lights or radio came on. Nothing happens now, except the strange clicking when the key is off or out. The first thing I thought of was the GEM or fuse box.
View 3 Replies
