Ford Super Duty (1999-2016) :: 2000 F250 - Manual Transmission Noise When First Started
Jul 31, 2014
I am new to being an F250 owner. Just recently purchased a 2000 F250 SD 4x4 with the 5.4 and a 5 speed trans. Got a pretty good deal on it, because I knew some work had to be put into it, and do plan on dropping the trans. Currently, if the truck has been sitting for a little bit, not cool, but not running for a little bit, when I start it, whether it is in gear or in neutral, there is a noise coming from what seems to be the clutch area.
After a couple minutes of driving, this noise goes away and all sounds as it should. A little bit of researching turned up the possibility of the throw out bearing being bad, however, I found other posts online that doubt this. Another symptom that I assume is connected is that if I go to put it in reverse at 0mph from neutral, it grinds.
In order to go into reverse, I have to press in the clutch, put it in first, then put it in reverse, at which point it goes in no problem. I had already planned on replacing the clutch because it seems to me that would be the logical choice as to where the problem originates, so no issue there. But perhaps I'm wrong??
View 13 Replies
Advertisement
I am changing my 99 f250 4x4 from auto to manual tranny. I am just looking for pics of where the hydro line runs. I don't want line rubbing something and ruining line. Like does line run under the cab wiring harness? Like between wiring and firewall? Where on firewall does reservior get mounted usually? Are the holes all ready there for it that I am not seeing?
View 1 Replies
Well, I've been meaning to get to servicing/re-greasing the front hubs/bearings for a while but somehow it keeps getting moved down the list.
2000 F250SD 4X4 Gas Manual Hubs+Trans
I'm currently going through the many threads that turned up in my search query.
Driving slow with the windows down it seems like a low whine or squeal coming from the left front. Tone changes when working the steering wheel left and right. Haven't detected any grinding sounds. Any other techniques for isolating the problem? It's going up on jack stands tonight and I'm going to see if there is any wobble from the front wheels and I'll listen as I turn each of the front wheels. Oddly, the right front hub is hard to turn. Left front turns easy.
Viewed Rob259956's videos on servicing the hubs. Currently researching accessing the wheel bearings. It seems pretty straightforward. Truck has been off road but not mud bogged or anything like that. I'm guessing a bad bearing will be easy to identify as will a bad o-ring but any other stuff I should look closely at?
View 6 Replies
Driving to work the other day my transmission shifted down and the transmission light started blinking. It felt like it geared down like it was in 4x4 I was doing about 55 at about 2600 RPMs. This has happened twice now and lasted around 2 minutes then stopped and ran great.
View 2 Replies
Question, my truck started to have a miss under normal acceleration, when I really get on it, it clears up? I also noticed a bad sulfer smell at idle. Im thinking the cat is possibly plugged? Truck had 172000ish on it, and the cat is original. I did do a big tune up this past fall, new plugs, coil packs, air and fuel filter. Should I put a new cat on it? And a new oxygen sensor?
View 9 Replies
I have a new to me 2000 F250 7.3 diesel with automatic. Truck has 185K miles and tranny is starting to slip occasionally. Do these trucks come with a OEM tranny cooler or do I need to add or upgrade the OEM one. Someone also told that there is something called "bulletproofing" the tranny on these trucks. BTW, what would be a reasonable cost to have a two wheel drive auto tranny done on my truck?
View 7 Replies
I have a 2003 f250 4x4 with a 5.4 motor the automatic trans is shot. I can get a replacement trans from 2000 f250 4x4 with the v10 motor. I tried my best to research it bell housing supposed to be the same so it should fit. But I'm not sure what they changed in those years internally or electronically.
View 2 Replies
I see an oil stain on/surrounding the lower half of what I'm guessing is the PTO cover on the side of my manual transmission. (rectangular plate bolted to side of tranny) I couldn't find a gasket at any autoparts stores. Is there a gasket or did Ford just use a sealer? Would red RTV work ok here instead of a gasket? Or should I use something else?
2004 F250 SuperDuty 4x4 CC, V10, 6 speed manual tran
View 1 Replies
I have a 2000 F250 SD with the V10 engine. The problem that I am having with it as of late is that whenever I perform a full turn I hear some clunking coming from the front end. The clunking is similar to that heard from cars that use CV joints FWD but of course it sound more "manly"
Anyways, my truck has the full axle on front so I suppose it could be either the u-joint at the hub or the hub itself. I would like some pointers so I can acquire the required parts.
View 14 Replies
So, yesterday when I got home I stopped at the barn to unload a few bails of hay and when I got back in to crank it, nothing happened. I turned the key and nothing, so I figured I would just worry about it today. However, when I turned the key back to off and started to take it out all sorts of stuff started to happen. There was a clicking noise and a dinging, not like when the door is open. It was quicker. Also, when I turned my key back on none of my dash lights or radio came on. Nothing happens now, except the strange clicking when the key is off or out. The first thing I thought of was the GEM or fuse box.
View 3 Replies
Changing from manual windows to power? I don't want to swap doors because of the repaint issue but wondered what is involved, if it's even possible. I just read how to convert the rear windows on a Super Cab to power and it got me wondering about the front.
View 2 Replies
I just bought a 2011 F250 Super Duty 6.2L and the manual A/C buttons were stuck on Max A/C and wouldn't change. I fiddled with every switch on the dash thinking it might be a stuck switch and eventually all the buttons started working. This truck has SYNC, which works fine, and I can't find anything else wrong with the truck.
When the buttons are lit, it blows good and cold, in A/C and Max A/C. The problem I'm having now is that they won't light up at all. Visual inspection shows nothing obvious under the hood, and it has a charge of freon. I drove and it id working just fine, but stuck on the Max setting. I'm thinking electrical gremlins, like stuck switch or a relay...
View 1 Replies
My manual hubs on my 2006 f250 have become very hard to rotate so I would like to replace them. I saw that bronco graveyard has Warn hubs for a Dana 60 front axle. Is this what I need? My door sticker with the axle code is illegible, and I want to make sure I get the right hubs.
View 5 Replies
I have a 2000 F250 5.4 that has a ticking/knocking noise. After about 30-60 seconds of first starting the truck in the morning, the ticking/knocking noise appears. It sounds like its coming through the exhaust system and seems to be louder under the front passenger side wheel well. When I rev the engine up, it seems to go away. Does this engine have a cam phaser? Could it be timing chain slap?
View 11 Replies
I have a 2000 F250 2wd 6spd with a loud banging noise that has been vexing me for quite sometime now. The bang happens when I go over bumps (even small ones like road reflectors) while driving. I don't think it is suspension related since all the ball joints, front/rear swaybar and endlink bushings have been replaced fairly recently. All the springs and bushings also look okay.
The noise seems to come from the rear, and I notice that if I let off the gas when I go over a bump, it does not make a sound. Conversely, if I am accelerating aggressively and hit a bump, the sound is much louder. Also, if I step on the clutch while keeping my foot steady on the gas, it makes a bang. Jumping up and down in the bed while the truck is parked does not recreate the sound. I have already greased the driveshaft spline joint so I'm thinking the sound might be differential or transmission related. What it could be?
View 9 Replies
2000 Ford F250 crew cab 4 x 4 with 7.3. 6 speed transmission.
I just had a new clutch installed and now I am have a grinding noise when putting it into 1st gear and when I change from granny to first it will grind also. I did not have this issue before having the clutch replaced.
I have also just had a new hydraulic clutch kit installed.
View 5 Replies
2016 F250 6.7L 4x4
I getting some tranny noise when towing on incline from a complete stop. When I slowly press the gas pedal I hear grinding noise. If i press the gas more my truck starts to move and the noise goes away. It doesnt happen all the time. This started right after my 1000 miles recommended break in before towing per ford manual.
My truck now has 2800 miles and the grinding noise occurs intermediately regular driving. Mostly on steep incline or decline. I haven't taken it to the dealer yet because I cant recreate the issue all the time.
View 6 Replies
My 2000 f250 7.3 has pretty sloppy steering and noise in the front end when going over bumps. I have replace the drop links, swap bar bushings, both wheel hubs including new seals and the drag link. The rest of the front end seems to be in good shape. I put it up on jack stands and there is some movement in the front end but it seems to all be in the steering box.
Steering box appears to be original with 220k miles. I went to tighten it and it appears the PO did it at least once already. Is it safe to try tightening it again? Does tightening it increase the risk of failure? I'd like to try tightening it first but not at the risk of losing steering at 65mph with my kids in the truck.
View 14 Replies
When my truck is parked, I go to the rear tire and shake it back and forth and hear a slight clunking noise from either the tire or rear end. Its like the axle is making the noise?
2000 7.3 Power Strke Super Crew 4x4
View 6 Replies
I bought a 2000 F250 V10 Super Cab. Oddly after a few weeks it has grown on me. There has been a clunking noise out of the right front over bumps. I traced it to a bad axle bearing. The u joint moves up and down about a 1/2 inch. Besides pulling the hub/bearing assembly out and removing the axle are there any surprises getting the old bearing out?
View 1 Replies
I have a noise with my new (2.6k miles) 2000 Diesel F250 Crew Cab. When I make low speed, right turns while crossing any type of depression in the road I hear a loud knock as if the left shock is bottoming out. There's an intersection near my house with runoff depressions across the road, I almost always hear the noise when making that turn. I've occasionally heard it coming from the right side when making a left turn.
View 14 Replies
