I have a leak from the oil pan gasket and oil coolant lines. From the research I have done, it looks like I have to lift the motor to change the oil pan gasket. Any way to get this done without lifting the motor??? 2000 f250 5.4 2wd....
View 4 RepliesI've been trying to figure out what is going on with my '99 F-250 V10, you can check out this thread for the back story
[URL]....
I did a compression check and the results seem inconclusive to me- see image.
Before I did the compression check I started to take the intake manifold off to change the gasket set and it's about 50% done. I'm at a crossroad now. Do you think I should finish switching out the intake gaskets or do you think it's more than likely a head gasket? I would hate to put it back together, it still smoke and have to take the intake and everything else back off to do the head gaskets.
Someone had mentioned a possible small crack in the cylinder wall that is closing up when the engine gets heat in it and obviously doing the intake and cylinder head gaskets would fix it if that's the problem.
1999 f250 with some mild upgrades. Trucks got 189,000 miles. Stole it from an older guy for 4k. In fantastic shape. As the weather got colder I noticed an exhaust leak. Took it to a muffler shop only to find that it's got an aftermarket header on the passenger side only. Is that common to replace only one side?. the gasket has gone bad and needs replacement. I wanna replace both headers?
View 8 RepliesI have a 2006 Ford F-250 coolant leak only when the truck is cold. Ive noticed it in the morning when I leaving for work. It looked liked it was coming from the passenger side yesterday and today it's on the drivers side when I'm sure is because my driveway has a small tilt to it I've looked everywhere I could under the hood and don't see it leaking.
I don't have any temp problems or white smoke and my coolant level has changed that much and for a few days the drip stopped now it's back. I tried to search for the answer but can't find it. I'm just wanted to make sure it's not the head gasket but I'm sure I would have a sign it it was. I will include where I saw it dripping from. It's parked on flat ground here ... That's where I saw a drip coming from driver side ....
I'm trying to troubleshoot a leak on my 08' F250 with a 6.4 powerstroke. It's been dripping coolant when cold pretty aggressively. Once the truck heats up, the coolant leak seems to mostly go away.
Here's a picture of the drip, it's marked by a dart, so you can see the location from the top (second pic). The radiator house connection around the engine seems dry.
Pic from Top ....
What's hidden here that could be causing the leak?
I have a 2000 F250 4x4 7.3 - About a month ago I drove across town and then noticed a strong hot brake smell from the rear of the truck. When I drove home about 2 hours later it was gone and didn't return until today. Today I stopped at a light with my window down and got the same hot brake smell, looked in the mirror and saw smoke coming from my drive's side rear wheel.
I carefully drove home (the smoke was now gone, all i did was cycle the parking brake release a couple of times) and pulled the wheel off. Rotor was really hot but smooth and clean. Brake caliper and pads looked great (no sign of the pads glazing or dragging, dry as a bone). The inside of the rotor was wet with oil. The brake shoes and components were soaked with the same fluid/oil.
Does this sound like a typical hub seal issue? Excuse my ignorance since I haven't had the rear hubs apart before but does the gear oil in the rear diff go into the axle tubes? I know the front tubes are dry but I didn't know if the rears are different. The amount of fluid on the brakes seems to be more than the little bit that is inside the hub. I need to pick up the parts and rent/purchase a couple of tools to replace the seal so I want to be as sure as possible that I'm on the right track...
I just bought a 2000 F250 SD 6.8 v10 and its mixing coolant in the block and leaking oil. I'm debating on just dropping a newer v10 in it but im just not 100% sure that this engine is shot. It runs great when there's oil in it and I can't even tell there's any problems going on for well over a couple hours after i fill it up with oil.
View 8 RepliesI plan on replacing the brake lines on our 1999 Ford F-250 Super Duty. The rear line blew out right by the hose, on the framerail. All five lines, all five hoses. What size lines? Looks like front two are 3/16", rear two over the axle are 3/16", and the rear line in the frame is 1/4".
We are removing the bed (2013 bed) to make things easier. I am thinking fuel lines and parking brake cable while the bed is off. I have stainless steel hoses from KLM performance and I am also planning on replacing the rear rubber hoses. Obviously I'm using nickel copper line. There shouldn't even be an option for other brake line.
[URL].....
I have a 08 f250, my abs is giving me nothing but problems, always have, have any of you's ever ran new brake line and by passed the abs?
View 2 RepliesI have been having non-stop issues with my tranny. After getting it rebuilt (by some BS shop my warranty company told me to go to) it is starting to leak when parked for more than a day. It generally pisses out about 1/2 to 1 qt overnight when this happens. I crawled under the truck and it looked like the fluid was coming from the pan gasket. Rather than taking it back to the mechanic that decided to take 3 months to fix it last time, I swapped out the gasket myself. This did not solve the problem. Where and why else could it be leaking from? It is not over filled, I have checked multiple times. I would prefer not to have to hand my truck back over to the incompetent 'mechanic' that 'fixed' it last time.
View 14 Replies2001 Ford F250 5.4 gasoline. At the most recent oil change my mechanic said there was an oil leak and he had dyed the new oil and cleaned everything up and to come back in 100 miles.I just did so and he said that it was a leaking head gasket. He said to do the head gasket replacement right or to put in a rebuilt engine would be close to same and he would recommend the replacement. He said it was not a heavy leak and probably ok to drive another 10,000 or so miles first. Just returned from a trip where we drove 15 hours straight (30 degree temps) and the truck ran fine and no overheating.There does not appear to be oil in coolant or vice versa. I took the cap off overflow coolant and cranked and revved and no disturbance whatsoever. I read somewhere where a mechanic was saying it was impossible for this Ford engine to leak oil from a head gasket failure .
View 7 RepliesTo all those folks that said I had a head gasket putting pressure into my cooling system and causing it to overheat, you were right. It is a 2003 F250 with 80000 5.4 l. I have had to replace mexhaust manifold bolts on left side (horrible job, couldn't get one out). Back fenders are rusted out, under the extended cab rusted, doors are rusting at the bottom. My friend/mechanic said it was time to get rid of it. I don't really have thousands of $$ for a different one, but also, replacing the head gaskets are in the thousands for a repair bill. I have looked at used 2008 250 4 door and they are 20000+++ sheesh, but a new one is out of the question. Do I get the gasket situation repaired?
It does not act up all the time, some times it never overheats, sometimes it will. Somewhat infrequent ( I had one mechanic look at it and he tried 3 different times, and it did not overheat. Temp gage will peg, coolant resevior will overflow, but is not hot (100 degrees). I dont have the really have the money to put into a newer model, but I am worried about being nickeled and dimed to death after dumping a couple of thousand into a head gasket, plus I suppose I need to have the other side manifold gasket/bolts checked too. It seems like low miles to be having issues, yes I realize all will rust, but this year, as evidnet in our area, was really suspect-able to rust.
Not worried about the body, is it worth it to spend 2500 for head gasket repair, or trade up a couple of years, less miles, etc. My worry is, I already had to fix 1 exhaust manifold gasket, know head gasket to fix a cooling issue, do I cut my losses and move to another truck, or spend the money for repairs. I don't really have money for either but want to make a good decision. Truck has not been abused and has been serviced as scheduled. Had to put on new brakes and rotors, as would expect, and ball joints too. Oil looks fine, no contamination, and coolant is clear. Will the head gasket get worse? As I said before, it is intermittent, but I don't trust it for long trips.
Having some coolant leaking from the EGR unit in my 2011 super duty.. Dealer says it's a 14 dollar part, but labor is a few hours to replace.. Not sure I see how that can be, but I wanted to ask on Here to see how long this should take..
View 1 RepliesI have a 2013 F250 which has both the Manual and auto locking hub feature. I tried to plow my driveway this morning and after making one pass I put the truck in reverse and could not back up my steep driveway. The truck is showing locked in 4x4 on the dash, the 4x4 control is in high lock but the front wheels will not turn. It has been very cold here lately (-30) and I'm wondering if the vacuum lines for the auto locking hubs have frozen. I have switched the control out of 4x4 and back in several times, and it does lock in again, but as soon as I put the truck into reverse, they unlock again. The hubs are covered with ice and snow right now so I have not yet tried to manually lock them.
View 14 RepliesI am replacing the head gaskets on a 2006 Ford F250 6.0 .... I have heard that I should replace the head bolts with studs. Do I torque the studs just like the bolts?
View 5 Repliesmy truck at 210k miles got a new radiator (seeping at seams), thermostat, water pump (bearings shot, leaking), intake manifold (The crossover was leaking). It now has 227k miles. Oil leak in rear at head gasket by starter (bad head gasket?) It overheated the other day( blowing coolant out the expansion tank needle in the red) Replaced thermostat. Drove around for two full hours, seemed fine, Drove to work today it overheated ( same thing, blowing coolant needle pegged) didn't make it to work. There are no external leaks and its not putting steam or white smoke out the exhaust. I read somewhere that a blown head gasket could make the truck overheat, is that possible? What all could cause this problem?
View 6 RepliesI needed to replace the intake manifold gasket on my 2002 f250 v10. Tore everything apart put the new gasket in which was the same as the old one lyrics to notice something isn't right. I have been driving the truck for over 10 years like this. Is it OK to just continue bolting everything down and go on like this? I am guessing the prior owner 10 plus years ago put the wrong intake on. I keep looking up intakes but they all look just like the one I have. Also that port exposed is on the back passenger side.
View 3 RepliesI'm looking at replacing the valve cover gaskets on my 02 f-250, it's a 7.3L.
Looking at them on line there are many different brands. What have you used on your 7.3L, and which has worked the best for you?
After replacing most of the underside of my Super Duty, Complete front end, backing plates, brakes, rotors and shocks, I have a misfire code on cylinder #4. I replaced the plugs, cleaned the MAS and filter and rotated the coil to cylinder #1. Still have a misfire on #4 and noticed the coolant slightly low and some condensation on the oil cap. Could this be the intake gasket? My mechanic is away for 2 weeks and I think the price at the dealer will kill me. I have 63K on the truck, don't tow and plow mostly family members. It's getting a little rusty but is still in good shape.
View 13 RepliesI have a 2002 F250 5.4with Air Conditioning. The valve covers are leaking and the gaskets need to be replaced. I am attempting the valve cover gaskets. I was able to get the drivers side cover off with some difficulty. For the passenger side valve cover. There is very little " no" room to get at the bolts. I read somewhere that I may have to drop the engine on that side. I will do that if I have to.
View 5 RepliesSo I've put about 1000 miles on my 03 F250 since buying it, and just the other day it's started leaking from the rear of the passenger head gasket. Enough to drip on the driveway and exhaust, and have some exhaust smell. 126,000 miles, 5.4
I've checked with my local ford dealer, and It also needs passenger exhaust manifold and studs, so the dealer price to tack that on would be a whole lot more too since there are already a couple studs broke. It would be best to get it done when the head is pulled.
I've checked with several local mechanics, and none of them are interested in pulling the head on this engine. That has me concerned about doing it myself too..especially since it fits in my garage with only a few inches to spare..