The other day I was under my truck and noticed electrical plugs behind the front splash guards. What these might be for? I have a 00 F250 superduty XL model with the 5.4.
View 8 RepliesI recently had need of replacing my left exhaust manifold on a 2000 F250 4 x 4. I removed plastic inner fender well. Now I have a two pin harness with both white wires. One is white with red stripe, the other is white with black stripe. The harness is round with a locking square on one side. The harness is located about 10" from bottom of inner left plastic fender panel. It has 2 mounting pegs. Where the heck does this connect?
View 13 Replies2000 F-250 Super Duty
I was replacing my headlights, which required me to splice in their lights to my parking lights, and I seem to have shutdown ALL my parking lights. I did a test after twisting my wires together and everything worked fine. Then I soldered and heat shrunk them and somewhere during that process I lost all the parking lights.
I checked the 8th fuse as per the manual (for Parking Lamps) with a multimeter and it checked out just fine.
Figured it was the time to ask the experts on here where I should go from here. Are there some other fuses I could be missing, or maybe some else I could do?
Solved: Bad fuse in the #8 slot in the Power Distribution Box (under the hood, near Cab, driver's side)...
I need to know what the name of the part is that the front shock mounts to on my 2000 f250. Its terribly rusted on both sides and id like to learn more about replacing it. Might me called a shock mount? It saddles around the main frame on the truck.
View 3 RepliesI have a 2002 f250 super duty 4 dr w/ full lenth bed. has v10. had oil cooler problem, motor oil in coolant. fixed that, then rad started leeking, replaced that. now blowing freeze plugs on block. replaced i on drivers side rear, now popped one on pass side. whats going on? i know oil pressure is more than water, did the oil cooler leak losen the freeze plugs? What size freeze plugs they are? no parts house around here knows.
View 14 RepliesI have an 01 F250 with a v10. Driving through heavy snow in 2013 a plug blew out. Should I expect this to happen again if I do some heavy hauling and should I do something preemptive?
View 14 RepliesAs the title says are my front leaf springs bad? I got this truck 2 years ago and replaced all the ball joints, shocks, sway bar links,front hubs, rotors and brakes along with all the seals. I have a clunk in the front and I can't figure out what it's coming from. Could my leaf springs be clacking together? Truck
is a 2000 F250 SD v10.....
Driverside front
Rear spring
I have a 2000 f250 4x4 with 4 wheel abs. The front passenger side caliper keeps locking up while I'm driving and won't release and when I hit the brakes it pulls hard to the drivers side. I have put two calipers on the passengers side and put new brake lines on.
View 8 RepliesWell, I've been meaning to get to servicing/re-greasing the front hubs/bearings for a while but somehow it keeps getting moved down the list.
2000 F250SD 4X4 Gas Manual Hubs+Trans
I'm currently going through the many threads that turned up in my search query.
Driving slow with the windows down it seems like a low whine or squeal coming from the left front. Tone changes when working the steering wheel left and right. Haven't detected any grinding sounds. Any other techniques for isolating the problem? It's going up on jack stands tonight and I'm going to see if there is any wobble from the front wheels and I'll listen as I turn each of the front wheels. Oddly, the right front hub is hard to turn. Left front turns easy.
Viewed Rob259956's videos on servicing the hubs. Currently researching accessing the wheel bearings. It seems pretty straightforward. Truck has been off road but not mud bogged or anything like that. I'm guessing a bad bearing will be easy to identify as will a bad o-ring but any other stuff I should look closely at?
I have a 2000 f250 with auto/manual locking hubs and today the 4x4 quit working. The light comes on the dash and the drive shaft and u joints turn but the front wheels don't turn even when its locked in. I assume its the hubs? And when I am going down the highway about 75 the front starts making a hellacious noise but stops if I slow down is this connected?
View 11 RepliesMy 2000 f250 7.3 has pretty sloppy steering and noise in the front end when going over bumps. I have replace the drop links, swap bar bushings, both wheel hubs including new seals and the drag link. The rest of the front end seems to be in good shape. I put it up on jack stands and there is some movement in the front end but it seems to all be in the steering box.
Steering box appears to be original with 220k miles. I went to tighten it and it appears the PO did it at least once already. Is it safe to try tightening it again? Does tightening it increase the risk of failure? I'd like to try tightening it first but not at the risk of losing steering at 65mph with my kids in the truck.
I bought a 2000 F250 V10 Super Cab. Oddly after a few weeks it has grown on me. There has been a clunking noise out of the right front over bumps. I traced it to a bad axle bearing. The u joint moves up and down about a 1/2 inch. Besides pulling the hub/bearing assembly out and removing the axle are there any surprises getting the old bearing out?
View 1 RepliesI have a noise with my new (2.6k miles) 2000 Diesel F250 Crew Cab. When I make low speed, right turns while crossing any type of depression in the road I hear a loud knock as if the left shock is bottoming out. There's an intersection near my house with runoff depressions across the road, I almost always hear the noise when making that turn. I've occasionally heard it coming from the right side when making a left turn.
View 14 RepliesI went to replace a headlight bulb and now I lost electric in the cab. I have no interior lights, no power window or door locks, turn the key on, no crank, no cluster, no radio, no chimes, the upfitter switches work, the mirrors power fold and telescope. Have power to both fuse boxes and battery is fully charged.
View 6 RepliesSo a truck that was running fine Sat for 2 weeks. Battery died so i sent some coworkers to jump it. They tried using a welder which they didn't get turned down enough. Now the wiper motor stays on even without the key. Radio doesn't work but the dash light still comes on. With a new battery installed it turns over but doesn't start. I know something had to get fried but where to start. Thinking about replacing all fuses and relays...
View 7 RepliesI have a 2000 f 250 that will not start... I have replaced many parts all electronic sensorsm the past week i have spent in the neighborhood of 1800.00 on this truck. Cps, icp, idm, ebps, fuel filter, new oil, hpop level good, gpr, all new need starting........
View 4 Replies2000 f250 7.3. Today I tried using the 4x4 and no light or anything. Here is what i have tried so far. Swapped the relays and also swapped them with the towing relays with no change. Not getting any voltage to the t-case shift motor at the selector switch testing between pins 2 and 3 there is 4.3 volts with switch in 2wd 2.4 volts at 4 high and 1.09 volts at 4 low. Where to go from here? it worked fine 3 days ago.
View 2 RepliesI have a 200 f250 v10 srw 4x4.. I've replaced the auto front lockers with warn premium manuals. I cannot get power to the front wheels. The lockers appear fine. I hear the actuator function when I activate 4x4. Whats the possibility of a bad transfer case or front diff and how do i check? I've searched but there seems to be a lot of non-answers.
View 7 Repliesmy 00 f250 has the air bag light on all the time. it does not flash it just stays solid. it was like this when i bought the truck @3 months ago. also the passenger air bag switch does not light up when you use it. is this causing my airbag light to stay on?
View 9 RepliesI just bought the truck and the ac was working and now out of nowhere when you turn it on it just blows hot air so I just assumed it was out of free on so I bought an ac pro but that did nothing.
View 5 RepliesI have a 2000 F-250 V10 that misses (cylinder 10) at the idle, once you give it gas it runs correctly again. I am at a loss. I have replaced the plug, tried moving coils from one cylinder to another to see if it shifts the miss, and it has new injectors. What this could be?
View 9 Replies