I have a 4r100 in my 2000 f250 7.3. I am getting a P1746-EPC Solenoid, open circuit. Does this mean this particular solenoid in the solenoid body has failed and should i replace the solenoid body?
View 3 RepliesI have a f350 2000 4x4 automatic 170.000 miles. Service light on and OD light flashing. I have code p1747 "EPC solenoid short circuit"
This code make that the engine runs slow without power and hard shifting. I change all the solenoid body and check all wiring.
Later using a voltmeter i separate EPC solenoid wiring and see that have 5 volt. If I don't accelerate more 2000rpm OD light is not flashing and truck works normal but slow.
When I accelerate more than 2000rpm OD light begin to flash and transmission fail more. I check that EPC wires mark about 0 volts when OD light is flashing. Transmission hydraulic system seems to be ok because oil is very red and clean. Maybe another sensor is making this failure....
I have a 2006 F-350. I got a code p2623 ipr circuit open. I ordered a new one and currently waiting on it. I pulled the old one and the screen has been replaced already. How often do these valves go bad? Is there anything else I should check?
View 6 RepliesMy scanner reads P0001 Fuel Volume Regulator Control Circuit Open. My truck shuts down without warning, runs great otherwise. I've changed 2 grey CPS units and now have the Black IH one installed. What the Fuel Volume Reg.is? Is it the IPR on the HPOP?F250SD 7.3 225,000 miles.
View 10 RepliesI recently purchased this truck so I don't have any history on it. It's the V10 motor, automatic, 4 wheel drive, with a crew cab. I took it to Advance Auto to have them read codes and it came back with torque converter solenoid fault and 2 other codes related to that part. I didn't get to see the actual code numbers.
I've talked to 2 transmission shops and they said they could throw a solenoid pack into it, but that it might not even fix it. The truck drives fine, shifts fine, the tranny oil looks and smells fine, so I'm tempted to not worry about it until something else happens.
The truck has 217,000 miles on it...
I recently picked up a 2005 f250 SD 5.4 4x4... I was having issues with sporadic shifting and wandering shifts while cruising around 100kph, scanned it and came up with p0721 OSS sensor circuit performance fault.
I checked the harness and all looks fine, now I attempted to remove the OSS at the rear of the tranny, got the 8mm bolt out however could not, for the life of me get the sensor out. I tried not to use pliers to twist the sensor or anything for fear of breaking the sensor off and having bits go into the transmission.
My 2001 F250 will not start (clicks). I verified its not the battery and even tried to jump start it. I have never replaced a starter- but before I do that I read where there is another solenoid under the hood somewhere. I always thought there was just the one on the starter itself.
Two questions:
1. where is that other solenoid located and should I replace that first?
2. How difficult is it to replace the starter? I am pretty handy.
The issue is that I cannot get it towed easily - I just need to get it started at least once since my plow is still installed and it's hooked up to a trailer..
99 F250 Super Duty 5.4 has a p7147 error. Traced all wiring cant find any short. Bought reman solenoid pack # are f81p-7g391-cb with green cover my old one in trans is f81p-7g391-ba with blue cover. Are these interchangeable? Have tried to read up on pwm & nonpwm and getting confused.
View 2 RepliesI have a 2010 f 250 super-duty and i cannot get vacuum past the solenoid mounted on top of the radiator. Ford has given me nothing but bad advice. I know i have a vacuum leak after the solenoid and need to replace the lines going to the two hubs but when i switch on the 4wd and hook up a vacuum gauge the vacuum is good up to the solenoid about 12 inches. i constantly have 12 volts going to the center lead but nothing else in the other two leads either in 4 high, 4 low, or 2wd. Am I missing something here? shouldn't there be a voltage change when i turn the switch to 4wd to actuate the vacuum solenoid to let the vacuum pass thru the solenoid? I have tried replacing the solenoid but that did not work. Also use rubber vacuum line and make at down to the hubs?
View 4 RepliesI have a 2002 F-350, 7.3 that is not charging. It has no power coming in on the big supply lead on the back of the alt. I traced the cable back, and it goes to intake heater solenoid. Cable is good, but intake and glow plug solenoids both have no power coming to them. I am guessing there is an open circuit between solenoids and starter. My question is, does the power come right from the starter, and is there circuit protection in there someplace?
View 2 RepliesI have a 2006 F250 Super Duty w/ turbo Diesel. Took to dealership for "hopping" feeling when turning sharp. Was told that 4 wheel drive solenoid was bad. Where this solenoid is located? I know I can fix but want to know where it is located.
View 6 RepliesCEL turned on this morning heading to work. Truck drove completely normal with no signs of altered performance.
Stopped by Autozone after work and they checked it with a code reader.
Came back with P0442 - "Purge Valve Solenoid"
Part sold with or without bracket.
Is this a common part to fail? How can I be sure it has truly failed? Is it acceptable to reset CEL and see if it fails again? If so, how do I reset? Where is part located?
2011 6.7... My truck is throwing code P2033 Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor. What is the part number for that sensor?
View 6 RepliesHave an intermittent miss I can feel when driving 2006 F250 5.4 l 4x4 stick; Freeze frame from Cen-Tech 60794 (from Harbor Freight) scanner follows.
DTC CNT 0
DTC FRZF P 0352
FUEL SYS1 OL - FAULT?
FUEL SYS2 --
LOAD PCT 25.9
ELT (DEGREES F) 186
SHRTFT 1 0.0
[Code] ....
I can operate the scanner but what these ranges should be. What might be causing the miss? This scan shows 951 rpm, I was idling along in 1st in traffic, but I have also felt the miss at 75-80 mph (about 2300 rpm) on the Interstate and at other times, with light loads in the 1500- 2000 range in town.
I'm having a turn signal issue with my '02 F-250 that started this morning out of the blue. Seems that when the signal switch is set for a right hand turn and the brakes are applied, the signal will then become solid, not flash, and then blow the fuse. Evidently something with the brake light circuit is overloading the turn signal circuit and not canceling when the turn signal is activated.
Here are a couple of things I have tried to narrow down the culprit.
1) Left turn signal works fine regardless if the brake lights are operating.
2) Brake light circuit operates fine by itself.
3) Right turn signal works fine but there seems to be a back-feed of power causing the center third brake light as well as the left side rear brake light to flash in unison. If brake lights are then activated, the flash stops and becomes constant thus blowing the fuse.
4) Emergency Hazard lights work perfect but the center third brake light again flashes as well which reverts back to some type of back-feed of power. Also, if brake lights come on, flashing turns to constant light and then blows the fuse again.
I guess my question is,. does this seem like the multi-function switch needs replacing or could this be a relay issue of some sort? I don' think its a ground issue simply because the left turn signal circuit as well as the center brake light circuit are both being breached when the right turn signal is activated. Your thoughts?
2002 F-250 Super Duty 5.4 V8
I have a 2006 f-350 6.0 and i went to fill up my truck with diesel. After that the truck did not start. Currently has the code p2285 - injector control pressure sensor circuit low. I tried disconnecting sensor, still no start.
I have the torque pro app and another 6.0 that I use for comparison. Check power at ficm 48 volt, flp 11.5v, FVP 11.5v. Hpop while cranking shows 1400 psi. removed oil filter and see low pressure oil ok, fills up reservoir. ipr at crank about 65%. fuel filter full of fuel.
Replaced the dummy plug on passenger side because originally hpop was very low psi 12. after replacement it went up to 1400 on cranking. What should I be looking at next, should I be removing ipr? should i be looking at crank sensor or cam sensor? Just installed 2 new batteries also because my dad kept cranking the truck until it died.
Checked to make sure fuel cut off relay not triggered, Ok. The truck has been having long cranks before it died. Also right now the injector cycling is 10 seconds long while on my other 6.0 it is about 4.
I have searched and tried everything that was suggested to open the hood on my 2000 and nothing works. When looking form the front you can see the hood release operate, but nothing happens. What part of the release do I need to operate to get the hood to open?
View 5 RepliesI just bought a 2006 F250 Lariat. The previous owner did not have a manual for the vehicle. When I open a door the dome light does not come on. Is it supposed to come on in that vehicle? The exterior light above the rear window that illuminates the bed of the truck does come on when a door is opened so it makes me think that there is a wiring issue with the dome light. I can light the dome lamps with the switches on the lamp housing so I know that it is working and the bulbs are good.
View 8 RepliesI just bought a 2009 F250 and when I open the door the dome light does not come on?? Is there a setting I am missing? Could it be a fuse?
View 3 Replies1999 F250 - When I open passenger door , dome light and door ajar is not working but in driver's side everything is working. I have read several issues with this but everything seems to be opposite way lights and ajar are always on
Earlier I change passenger side power mirror and same time i release door jamb electric switch to check it but still no light when connector was released...
I have a 1999 Ford Explorer with the V-6 SOHC that is stuttering and stalling when I try to accelerate. A very slight acceleration will get the vehicle moving, but anything coming close to normal gas pedal pressure causes immediate stuttering and/or stalling. Check Engine light came on when problem started yesterday.
Where is the EVAP System Canister Vent Solenoid? I bought a code reader after beating my head against the truck all afternoon and got code "P1451 EVAP System Canister Vent Solenoid Circuit Malfunction". My Haynes book says on the left side frame rail... can't find anything along there that looks like it (based on picture from Rock Auto for replacement part) and found some people online talking about it being in the engine compartment on the passenger side...
Just crawled all over the truck and I think I found the charcoal canister, but couldn't trace it back to the vent solenoid... There was something right next to the canister, but again, it looked nothing like the replacement part listed on Rock Auto...