Ford Super Duty (1999-2016) :: 2000 F250 - Axle Spins When Hubs Are Unlocked
May 19, 2013
I have a strange thing going on with my hubs i think. I have a 2000 f250 7.3 4x4 that I just purchased. Lettering on hubs were worn out as far as labeled locked or unlocked so I tried to turn the axel to see what position they were in. Drivers side spun freely but passenger side did not. Both hubs were counter clockwise and turning it to lock didn't change a thing.
Figured it was a bad hub so I jacked the front drivers side up. Spun tire with both hubs unlocked and axle didn't spin. Locked hub on drivers side and axle spun. Indicating the passenger side was unlocked. Then I locked passenger side and wheel would not turn. Ok. That seems right.
Jacked up passenger side front tire with drivers side on ground and axle spins no matter if its locked or unlocked. So does this indicate the hub is good and I should look at something else or could it still be the hub. Axle spins all the time and I don't want to wear anything out.
View 12 Replies
Advertisement
I am not up on the exact operation of the hub lock/unlock on superdutys but when following them, I can see the front axles still turning with the wheel. So even with them "disengaged" they still turn with the wheels?
If that is the way they are designed to do, why? Seems like efficiency could be gained by having them actually disengaged when not needed. And save wear on the inner housing seals.
View 11 Replies
I'm trying to figure out how much of my front end I need to rebuild. 130,000 mi on the truck. About 1/2 of those miles are off road. 2008 F350 FX4. Stock. Original front wheel bearing unit and hubs. I was under the truck today and before I put it on jacks I decided to see how much play was in the front end components.
I noticed when checking out the passenger side front axle at the u-joint that I was able to spin the whole u-joint and bearing with the wheels still on the ground. I wasn't able to do the same for the driver's side. Both hubs were set to auto although I know that the ESOF doesn't work. Is this normal? Am I supposed to be able to spin the axle with the wheels on the ground?
View 8 Replies
I have a 2000 f250 CCSB 4x4 with the ESOF auto hubs. The auto hubs won't engage automatically. They work fine manually. The transfer case is engaging and correct lights are coming on. There is a little bit of vacuum coming from the vacuum switch but it doesn't seem like much to me. All the dash HVAC controls work fine though. I Lubed and cleaned inside the hubs according to Guzzles directions.
While torn down, I blew through the vacuum port on the outside of the hub and there was little to no restriction. I don't think there is enough vacuum to pull the hubs, but is that possible if all the dash controls work fine? What pressure should it take to engage them? My next step is to pick up a vacuum pump and see if I can engage them with it.
View 6 Replies
We got a ton of snow dumped on us today and for some reason my 4WD has decided not to work this year. I have a 2000 F250 4WD Triton V10. The hubs click into the lock position and the dial on the dash lights up 4x4 but I am definitively not engaging into 4WD. I'm pissed because this is specifically the reason i bought a 4WD and it's failing me. I can't find a fuse panel diagram to save my life however all the fuses in the interior of truck look to be fine.
View 3 Replies
I bought a 2000 F250 V10 Super Cab. Oddly after a few weeks it has grown on me. There has been a clunking noise out of the right front over bumps. I traced it to a bad axle bearing. The u joint moves up and down about a 1/2 inch. Besides pulling the hub/bearing assembly out and removing the axle are there any surprises getting the old bearing out?
View 1 Replies
Ok I reinstalled the new rotors and pads clips and warning tabs. The rotors match the old rotors size , thickness and hub clearance. 2 questions
Vehicle still on stands ....
After tightening everything up on the passenger wheel and the rotor seem to have a lot of play or movement... Normal or not ??
Now drivers side hub and lug nut spindle is not moving , possible another issue ....
Passenger side spins freely ....
if I did not have bad luck I would have no luck at all with this truck
View 8 Replies
Starting about 4 months ago, when starting my truck, the starter would miss; I would turn the key to start, then the starter spins and spools up very high and loud but not crank the engine. I have to turn the key off to make it stop and then try again. Usually the second or third time it will grab and turn the engine and start. It happens about once a week or once every 10 or 12 times I start my truck with all the other times being normal. Doesn't matter if it's a cold start or already warmed up. It's a 2012, 6.7L F250 with 52,000 miles. What is causing it and how it can be fixed.
View 1 Replies
I just got a 99 F250 PSD, it had not been in 4wd in a while, now the hubs won't unlock.
My 01 F250 seemed to have strictly manual hubs. Turn right to lock, left to unlock. They may have been aftermarket, but on by the PO. Do I need to put some new Warns on the 99? Or can I lube then up and get them functional.
View 14 Replies
Brings back memories of my many projects from back in the day. Anyway, my uncle has this f250. He said 4x4 wouldn't automatically lock the hubs in. I tested the vacuum pulse valve on the fender and changed it out. Now the hubs will lock in when you turn the light on the dash but it will not unlock the hubs unless you go outside and manually turn the hubs to engage then back to auto. Only then will the front end be unlocked. I notice small puffs of air blowing back from behind the hub themselves so I was thinking it's time to reseal the vacuum portion of the hubs.
View 4 Replies
I have a 2010 F250 with 154000km (96000 miles) that we bought last week. When I was looking it over during the purchase I noticed the front axle didn't lockup in "auto", in manual lock it seemed fine so I figured vacuum leak or something like that. Yesterday morning I was in the yard and got a little hung up in snow drifts so just got out, locked the hubs and switched to 4x4 and I think the front end didn't engage at all.
So later on I had it in the shop installing the two way radio and decided to check the front end out a little more thoroughly. Vacuum lines seem fine, hubs turn fine but I notice the axle shafts both move up and down almost a quarter inch, that seems excessively loose to me. I've been doing some research on the internet and it appears the front hubs are serviced as a unit, also some information seems to point to needle bearings within the actual locking hub mechanism itself?
So the questions:
1. Does that front axle shaft seem excessive? What are the specs?
2. Can I replace bearings and seals only or do these units come only as assemblies? Inner hub, outer hub units? Wheel bearings seem fine.
3. With that much play is there a chance the outer axle shafts are worn also?
View 14 Replies
On my 2008 f250 I can not turn the hubs without a set of pliers...does that mean I need new hubs....
What auto tranny do I have with the 5.4.. is it a six speed...
View 14 Replies
Okay this is what I got; I recently purchased high mileage 2004 F250 Super Duty short box super cab 5.4 liter. Came with manual 4x4 handle on the floor so no 4 wheel on the fly and this eliminates the vacuum for the auto hubs so this will not be part of the problem. When engaging the hubs and ONLY when engaged the driver side hub grinds. The 4 wheel drive works but it sounds like its ready to grind itself into oblivion. I did pull the hub and the grinding was gone, I happen to have a spare hub that is good and the grinding returned.
I have jacked it up and made sure I have no play in the wheel itself and the axle knuckle on the axle shaft. Some say remove the front drive shaft? Or turn the wheels all the way in one direction engage the hubs and check for binding? I will do this in the morning, but what does that confirm if it not the hub. Could it be the passenger side echoing across? On my 99 Super duty I kept hearing moaning coming from up front like the breaks were shot and if you stuck your head out the window it was the back echoing to make it sound like the front.
View 3 Replies
2001 F-250 7.3. The auto lock hubs are not working on the truck lock hubs in and all works fine. First thought is the vacuum system has a leak or something of the sort. Had truck at the shop they are telling me the GEM module controls the vacuum to engage the auto hubs and the signal is not coming from the GEM and it need to be replaced. It was the GEM causing the problem.
View 6 Replies
About a month ago I bought a 2004 F-250 160xxx from a reputable Ford dealer here in town. The dealer performed a safety and emissions inspection, and spent about a grand on other repairs, as a condition of my purchase. Today I had it in the shop for an instrument cluster issue (at a different Ford dealer, closer to my house), and was told the vacuum lines were all messed up. Their write up is below:
"Check 4x4 operation. Transfer case shifts to 4x4 and 4x4 low. Front hubs do not engage automatically. Check vacuum at the hubs. No vacuum. Check the vacuum at the solenoid. No vacuum. Perform visual of the engine vacuum lines. There is no vacuum to the reservoir. Vacuum line is routed wrong from the fuel pressure regulator to the vapor management valve. There is other vacuum concerns. All of the vacuum line routing needs to be inspected and corrected."
The service rep told me it is questionable whether the 4x4 ever worked, although during the few weeks I've owned it, I could hear gears or other mechanical parts making noise which seemed to me to be in response to me turning the 4x4 electronic switch. She also said there was a vacuum line dangling loose with a screw in the end of it.
Before I contact the dealer where I bought the truck, I am planning my going-in position. But I wanted to get a sense of a) how serious of a problem this might be? and b) how reasonable it is that the dealer didn't catch this issue before I bought the truck while they were in their fixing other things?
The dealer who sold me the truck made it very clear that the sale was as-is, and I took it to my mechanic prior to purchase, though unfortunately he only had time for a cursory look at the engine. Obviously he didn't look closely enough to find this issue.
I'm not sure if I should ask the dealer who sold it to me to fix it, or ask them to allow me to return it, or sell it back to them, or if I should eat the cost of fixing it. How wrong would it be to try to trade it in for something else?
View 3 Replies
My manual hubs on my 2006 f250 have become very hard to rotate so I would like to replace them. I saw that bronco graveyard has Warn hubs for a Dana 60 front axle. Is this what I need? My door sticker with the axle code is illegible, and I want to make sure I get the right hubs.
View 5 Replies
I have a 2001 F250 4x4 and the ESOF switch not engaging hubs, currently I have no 4x4 lights coming on in the cluster when i turn the switch. I am not experiencing any of the vaccum symptoms that most people are suggesting. I When I turn the switch i also do not hear any relays clicking. Relays have been tested, and i waited for the 45 second transfer delay that the manual mentions. ESOF switch has power, and is working properly (I know because I bought a new one in attempt to fix the problem) Basically I have no responses from any of my 4x4 indicators or parts.
View 14 Replies
I recently picked up a '99 F250 Super Duty with the 6.8L V10 for a song.
The 4 wheel drive hubs are not working with the vacuum. If I use the manual lock on the hubs all is well. I ordered the Innova 31703 CarScan OBD2 + OBD1/ABS/SRS Scan Tool. It says it does Trans codes. I am hoping it will cover the 4 wheel drive too.
Maybe related, the heat is always on. Meaning I feel heat at my feet when the temp dial is cold and fan is off. I can't find the heater control valve to check the vacuum line.
View 14 Replies
My 2007 f250 power stroke 6.0. My A/C comp went out. After replacing it I was told that my fan clutch is bad and will cause the new ac to go out. My engine is not running hot. The fan still spins for a while after engine is turned off.
1) Could it have not been re installed correctly?
2) How do I know my Fan Clutch is bad?
3) How do I replace it myself?
View 6 Replies
But on my 2000 SD V10 the hubs are worn I just cant find which way to turn them to auto ?
I'm getting popping and such so I think I'm locked while turning.
Also.... IS there a way to check the COPS with a multimeter? I think I got a bad one.
View 1 Replies
I have a 2013 F250 which has both the Manual and auto locking hub feature. I tried to plow my driveway this morning and after making one pass I put the truck in reverse and could not back up my steep driveway. The truck is showing locked in 4x4 on the dash, the 4x4 control is in high lock but the front wheels will not turn. It has been very cold here lately (-30) and I'm wondering if the vacuum lines for the auto locking hubs have frozen. I have switched the control out of 4x4 and back in several times, and it does lock in again, but as soon as I put the truck into reverse, they unlock again. The hubs are covered with ice and snow right now so I have not yet tried to manually lock them.
View 14 Replies
