But on my 2000 SD V10 the hubs are worn I just cant find which way to turn them to auto ?
I'm getting popping and such so I think I'm locked while turning.
Also.... IS there a way to check the COPS with a multimeter? I think I got a bad one.
Having an issue w/ my 00 550. When I lock in the hubs there is instantly a noise, More of a squealing then a grinding. The truck goes in and out of 4x4 no problem and the noise is there locked in 4x4 and not locked in, as long as the hubs are locked in. I can't tell if the noise is coming from the 4x4 driveshaft but there is no noticeable play in the u-joints or the u-joints in the front axle. I did notice when I spin the 4x4 shaft by hand the passenger side joint spins slower then the driver, not sure if that's normal or could be the problem.
View 2 RepliesIts a 2016 F-250, 6.2L gas truck with the electronic shift on the fly transfer case.
I have put right at 22,000 miles on it like this, frequently at 70-80 mph.
What are the odds I have damaged it and is there anything I should do now that I discovered it - other than put them both in "AUTO".
Truck has been to the dealer twice and not once was this noticed. They blamed the squealing on the brakes which I knew it wasn't.
Well long story short, I had the the factory hubs in my 04 f-350 and I was driving down the road and it started making this horrible popping noise. So I pulled over and couldn't find anything and just curiosity locked in the hubs and all was fine. Made me think my hubs were bad, so I went and bought the warren premium hubs, installed them. Went for a drive and still the same noise is there when they are in free spin. But once they are locked in its fine. What this could be? Wheel bearings?
View 4 RepliesHad to make a sharp circular turn last night in a parking lot, with the steering turned to full-lock...noticed a very audible clunking or clicking noise during the turn...went away after full-lock turning was released. My hubs are locked in...but I was told there was no issue with leaving them locked in, even during the summer. And there shouldn't be...4x4 disengaged, of course. Must have been the u-joints clicking / clunking? Problem?
View 5 RepliesJust got done with a ball joint replacement on my 2003 F550, everything went together great, just as it should. Until I got to the drivers side hub lock.
I have Mile Marker 449s/s manual hubs. Turn from free to lock and theres this loud clicking sound about halfway to LOCK (passenger side doesn't do this). Hub will stay locked for about 2 rotations, then it unlocks and makes a clicking sound. You cannot turn the hub back to FREE, it gets halfway and stops. I tried forcing it and broke the spring fingers inside. Have a new set on order.
Is this a locking hub issue or an assembly error? I was going to take these steps.
- Take passenger side hub lock off and see if it operates normally or same on drivers side.
- If same, remove axle and re-seat/re-assemble everything again
Anything to specifically check? All the parts went back in, washers were in correct order, outer snap ring is in groove.
Ok so some one locked my hubs and put the truck in 4x4 4low i assume my aunt was driving it, truck wouldn't shift from 2 to 3rd is this normal since its in 4low. The shifter also seems pretty stiff and 4wheel isn't used much if there a way to know if 3rd gear toon a crap? Trans fluid seems fine not dirty or burnt...
View 1 Replies2008 F350 hubs wont stay locked in when in auto position. everything stays locked while in manual and 4x4 works fine, but in auto the hubs wont stay locked while spinning. I was trying to find the problem when i noticed that one hub stays locked all the time and the other locks and unlocks as it should but it wont stay locked while spinning. My question is do I have two bad hubs or is their a leak that wont let the hub stay locked? Also on the hub that wont unlock is this a leak problem as well or a internal problem?
View 5 RepliesSo I noticed the past few days my 09 F250 was clunking in the front end when turning hard even with the hubs in auto so I knew there was an issue in there somewhere. This morning I took the jack and found the passenger side would not release no matter which way the lock was turned. Pulled the locking assembly out and found a couple of the pieces of plastic cage broken (truck has 250k miles) which is to be expected I guess but the locking ring that holds the inner piece that slides over the axle stub was off and hanging next to the c-clip on the axle.
So with the plastic of the cage already being broke and the mileage on the truck it's clear I need a new lock for that side.
Here's my dilemma, I have to deliver a conference room table 200 miles away tomorrow morning that they need for meeting tomorrow afternoon at 3:00pm. I cut the rest of the plastic pieces and took the gears out leaving just the cover with the diaphragm and put it back on the hub. I can't come up with any logical reason why I can't drive the truck this way but just want to bounce it off the experts here before I take off on a 400 mile trip in the morning. The only thing I can come up with is if I were to engage the 4wd the vacuum might suck the auto-lock diaphragm in and pop it but otherwise I can't find any reason to not run it this way, the hub is still sealed up and free-wheeling just like if it were in 2wd anyway.
Today was the first time I have locked my wheel hubs in and used 4 wheel drive. However when I did all this i noticed that when I turn there is a growling sound but only when turning. It does not make the sound when unlocked and in 2 wheel drive.
View 4 RepliesMy 2005 has the ESOF system which has worked flawlessly. Recently I had upper and lower ball joints done and after that repair I had no auto locking hubs. ( independent shop messed up seal install ) they redid the job and it now seems like my front hubs are locking automatically because I am getting binding while turning. So this is the problem.. the front wheels do not "pull" only the rear wheels spin. If I manually lock the hubs I have 4x4 and can get out of being nearly stuck and everything works normally. What is wrong here? Does the shop need to redo the job again?
View 2 RepliesMy 2010 F350 shudders when turning right. From what I read it could be the auto locking hubs not dis-engaging or sticking in the locked position. Tutorials show it's pretty easy to pull the auto locking Hub out taking out the three screws holding it in place. My questions is what type of grease do I need to apply to the auto locking hub once I have them out and determine that is what the issue is?
View 13 RepliesI have a strange thing going on with my hubs i think. I have a 2000 f250 7.3 4x4 that I just purchased. Lettering on hubs were worn out as far as labeled locked or unlocked so I tried to turn the axel to see what position they were in. Drivers side spun freely but passenger side did not. Both hubs were counter clockwise and turning it to lock didn't change a thing.
Figured it was a bad hub so I jacked the front drivers side up. Spun tire with both hubs unlocked and axle didn't spin. Locked hub on drivers side and axle spun. Indicating the passenger side was unlocked. Then I locked passenger side and wheel would not turn. Ok. That seems right.
Jacked up passenger side front tire with drivers side on ground and axle spins no matter if its locked or unlocked. So does this indicate the hub is good and I should look at something else or could it still be the hub. Axle spins all the time and I don't want to wear anything out.
I have a 2000 f250 CCSB 4x4 with the ESOF auto hubs. The auto hubs won't engage automatically. They work fine manually. The transfer case is engaging and correct lights are coming on. There is a little bit of vacuum coming from the vacuum switch but it doesn't seem like much to me. All the dash HVAC controls work fine though. I Lubed and cleaned inside the hubs according to Guzzles directions.
While torn down, I blew through the vacuum port on the outside of the hub and there was little to no restriction. I don't think there is enough vacuum to pull the hubs, but is that possible if all the dash controls work fine? What pressure should it take to engage them? My next step is to pick up a vacuum pump and see if I can engage them with it.
We got a ton of snow dumped on us today and for some reason my 4WD has decided not to work this year. I have a 2000 F250 4WD Triton V10. The hubs click into the lock position and the dial on the dash lights up 4x4 but I am definitively not engaging into 4WD. I'm pissed because this is specifically the reason i bought a 4WD and it's failing me. I can't find a fuse panel diagram to save my life however all the fuses in the interior of truck look to be fine.
View 3 RepliesAll of the sudden ignition stays on aux when the key is removed. Starts and runs fine with key , also shuts off with key. However when key is removed all aux functions still work ie touchscreen reciever will not turn off, and door chime continues to ding. 2000 excursion 4x4
View 1 RepliesI have a 2000 F-350,7.3, 6 speed. Just the other day I made a turn and my passenger got her feet wet. It had been raining and I also had the ac on. A couple of days later the same thing happened, but it had not rained, just the ac on. What is causing this. I do see condensate discharging under the truck.
View 7 RepliesI have a 2000 F250 SD with the V10 engine. The problem that I am having with it as of late is that whenever I perform a full turn I hear some clunking coming from the front end. The clunking is similar to that heard from cars that use CV joints FWD but of course it sound more "manly"
Anyways, my truck has the full axle on front so I suppose it could be either the u-joint at the hub or the hub itself. I would like some pointers so I can acquire the required parts.
I have a 2013 F250 6.7 Crew Cab Single Wheel. Stock 20" Michelin tires and stock suspension. I have almost 20K miles on it. I just rotated the tires again and noticed that the rears are worn down on the inside. The fronts look perfect.
View 11 Replies2000 V10 F250 - daughter is using my truck and called to tell me the turn signals weren't working. She called me shortly after and said she adjusted the tilt and hazard lights came on and now she can't turn them off. I had her pull the hazard fuse to stop them. She then noticed the brake light weren't working. I don't know if the brake lights were because she pulled the fuse or she just noticed they weren't working.
A week or two ago, she said she parked the truck, turned it off and took the keys. When she came back out, the truck had rolled across the street. Periodically, over the years, I would go to start the truck and nothing happened. I would shift the gear selector in and out of drive. Then the truck started.
Finally, since I've owned the truck, the when I activated the left turn signal, the selector frequently wouldn't stay "locked" till I turned. So, are these related? Do I have multiple issues going on in the steering column. Where to start looking when she gets the truck home?
First off my trucks a 2000 v10 f250 with four-wheel drive and 2 wheel abs with about 230000 miles on it.
I Recently replaced my unit bearing on my drivers side because I thought it was the cause of a grinding that only happens on hard left turns but I wasnt the cause it was going bad causing play in the half shaft. I didnt seem to notice and wear on the shaft from bad needle bearings but I have to take it all apart again to be sure. Was just wondering what else could be the cause of this noise. I plan to pull the axel shaft and change all the seals.