The spark plug in chamber 2 blew off while the vehicle was in motion (approx 35 mph). Purchased replacement plugs and when I went to install, there was nothing for the plug to grab (i.e. appears that all of the threads on the block/casing are gone . Not sure what my options are.
View 2 RepliesI have an 03 F250 5.4L
Driving down the highway today, I notice my truck was jerking forward a little, hard to notice almost felt like I was hitting very small pot holes. I revved up a little to see if I could notice any noises and I got a loud pop. after the pop, got a noise like an exhaust leak so I pulled off to the side of the highway and popped the hood (engine still running). Noticed the noise coming from the passenger side most forward spark plug. Then noticed the part that the coil attaches too had broke off from its bracket and was unseated, shut off the engine and pulled it out to find the coil cover had melted to the coil.
The spark plug inside was moving freely so I took it out thinking it stripped from the header. Come to find that the plug had actually separated from its threading completely so just the core part of the plug had shot out from the cylinder, the threading and socket attachment portion still fully attached. I installed a new spark plug and new coil harness and coil. Seems to be running as good as new now. Is there more to this than a simple blown plug that I need to worry about?
I have a 2006 F250 5.4L. I was getting a noticeable misfire after not driving the truck for a while. Mode 6 revealed that cylinder #8 was misfiring.
I took off the coil/boot and there was coolant on the tip of the boot and some at the bottom of the spark plug well.
I cleaned everything up and put everything back together and that took care of that problem when I started the car. I also stuck a wad of paper towel by the intake manifold nearest spark plug number 8 and tightened the manifold bolts down a little. Some of them were not as tight as others.
I went back today and started the vehicle and it has the same problem again!
I took a look at the paper towel and it was totally dry! There is no coolant around the top of the spark plug well - only in the bottom of it. Where is this coolant even coming from? There are no coolant lines near cylinder #8. Is this a head gasket leak?
I have taken a look at the head gasket and that doesn't seem possible since the head gasket does not seal around the spark plug well at all as far as I can tell.
Did a tune up on 97 F250 5.8: plugs, wires, rotor button, cap. Truck ran after that, ran all next day and then shut off after sitting for about 30 minutes, had it towed home, put on new coil. Nothing. Found I have no spark. Have not replaced the distributor, have checked fuses that seem to make sense...all good. Self employed, very busy, so troubleshooting is a slow process right now, having to drive my F550 7.3, would really like my gas burner back.
View 1 RepliesHow to get the spark plug out of cylinder #4. I have the kit to take out the base of the plug out of the head if it breaks off. But I can't get the plug out. I think the plug broke off but not the electrode. So the electrode is caught up in the porcelain tip of the plug. It's pretty tight back there with the a/c lines and fuel rail and other stuff. I tried needle nose but they just don't grip it right, to get enough force to pull it. These are the plugs with the extended tips.
View 6 RepliesI have a 2001 ford f250 6.8 v10 with just about 183,000 miles on it my wife has been driving it and she told me it was running kinda rough so I took it for a drive and she was right so I pulled #1 COP and found it was full of oil and the same with#2 and #3 had a little bit of oil not as bad. What is causing my plug holes to fill with oil?
View 14 RepliesI purchased a 2000 F250 SD with 5.4L Automatic for a project with my daughter. After removing the fuel rail and the coil pack on the driver side I noticed two spark plug holes had oil in it almost to the top of the plug. I'm guessing it is a bad rocker cover gasket that is allowing oil to leak into the plugwells? Nothing I could find on the internet relating to this.
After removing the rocker cover the silicone gasket was intact but wet with oil. I purchased a replacement Felpro gasket but now understand they might need grommets for the crazy bolts Ford uses to hold the cover on the head.
Have a 2005 F350 4x4 SRW 5.4L with roughly 90k miles and I am replacing the original plugs. Broke three out of seven which was expected and have them replaced. You probably noticed I wrote 7 plugs above. The 8th plug which happens to be the #8 plug is giving me fits. I can't get a socket on it. The socket spins smoothly by hand with no ratchet over the plug but no upward movement. I cleaned the base of the hole thinking it might have some debris preventing it from hitting bottom. From what I can see after cleaning and blowing it out, the base of the hole is clean and there plug appears to have something for the socket grab onto. Out of curiosity, I have tried smaller and larger sockets in both 6 and 12 point with no luck. Is it possible the plug was set too deep in the head from the factory?
View 13 RepliesAbout a week ago I blew #10 spark plug out of my 1999 super duty. I was able to screw it back in, though it only has 2 1/2 threads now, and was able to put 12 ft/lb's of torque on it. I am driving it around and it is running fine but i am wondering if i am sitting on a ticking time bomb thats gonna blow at a random time, and if so what should i do about it. Should i just run it until the plug fully blows out, or is there an easier and cheaper fix that i could do if i fix it before the threads are fully stripped out. I have heard about Time Serts, but without pulling the head i would be scared of having a metal shaving get down into my cylinder and scratch the hell outta it.
View 14 RepliesSo my 2000 F250 has 182k and I am not sure when plugs were changed. Its got the 5.4. My 2001 Excursion has 102k on the v10 and I've read a few threads about blowing plugs and now I am scared out of my mind. Do I need to worry about breaking them or stripping anything?
View 6 RepliesWhat is the spark plug pattern on the 460 n where the wires go on the cap. And also how to time it.
View 1 RepliesI am changing the plugs in my 98 e150 today and I was thinking it was a .54 gap and 13 ft/lbs to tighten them. That sound about right?
View 9 RepliesI have a 02 F250 with 137 thousand miles. When it had 130 thousand on it I had the plugs changed unknowing that this year 5.4 was known for blowing the plugs.
View 14 RepliesWent to change the plugs on an 02 f350, the bolt holding the plug wire boot on doesn't seem to fit any standard size socket. 7 is too big, 6 is too small. 1/4 is too small, 9/32 is too big.
View 14 Replies2001 Ford F350 V10, 220K in crap condition
First of all on the left side 2 of the coils were so withered the rubber separated from the bolt and were loose. Without any tools I was able to remove 2 coils. Typically there is the hole and several inches inside hole is where the spark plug sits.
On cylinder 4 the spark plug is on a funny angle and is level with the hole or possibly poking up above the hole. Tried sticking the ignition coil over the spark plug but it wasn't correct. Leaving it alone until my cousin can take a look. Spark plug was tight but I didn't put a ratchet on it.
Wondering, is this the infamous spark plug blew threw the cylinder thing. Wish I would have taken a picture (I will next time I'm with truck).
Had codes for misfires on 4 cylinders but that was with 2 coils unplugged (way I got truck at auction)....I replaced 3 of them (1/2/6).Cleared codes...4th cylinder remained unplugged....And the only code I got after letting truck idle for 10 minutes was something about ignition coil D (which would line up with cylinder 4 I think).
I need to tap a bigger hole and put in an insert for the spark plug. I can see that the piston is far enough down so that it won't get harmed from the process. But if I don't get the intake and exhaust valves shut, and then use compressed air to blow out what chips I can, and then I start the engine for a few seconds to blow out anything else (with the coil unplugged of course) will a few remaining chips, along with some that may have gotten blown into the intake, be a big problem? It's an aluminum head, so I can't see the chips doing much damage before they go out the exhaust or end up in the oil filter. But I am just guessing. I don't have the tool to test when all the valves are shut. Also, is it possible that a valve might be in the way and get damaged from the tap?
View 11 RepliesHorn isn't working found fuse blown. Replaced fuse and horn stays on. Swapped relays still stays on. With fuse out pressing left side of horn cover on steering wheel I can feel/hear relay click. Pressing right side not so much. What and where to check? Is there a way to disconnect the horn buttons on the steering wheel?
View 1 RepliesMy son has a 2001 F150 with a 4.6L V8 that's blown a sparkplug from # 3 cylinder. The plug looks as if struck by lightning and has a burn groove as deep as a kitchen match stem the full length of the threads.
How difficult is an engine swap/change using another 4.6L? Neither of us have extensive mechanical backgrounds but plenty of aptitude.
Last weekend my number 4 spark plug blew out while on the highway. The truck stayed on long enough for me to get off the highway and pull over before it died. I towed the truck home. Last night I repaired it with a helicoil and replace the spark plug and coil. Now the truck cranks but won't start. I noticed that my theft light flashes fast and doesn't stop after a few seconds or during cranking. I still haven't tested relays or fuses because it was late after the repair. I will be checking those tonight.
I will be reading and taking suggestions and posting my results tonight while I'm working on the truck. I will be checking the fuel pump and PCM relay tonight. I will also try 2 different keys and checking the Inertia switch on the fuel pump to see if that tripped. The truck is a 2001 F-150 Lariat Supercrew with 150k miles on it. 5.4 liter engine.
I was going to change the spark plugs on my 08 Camry CE today, so I removed one of the starters, and used my spark plug socket to extract the plug. The plug was sticking, so I pulled my socket out to get a better look at the plug, but when I pulled it out I noticed that there was a brown slimy liquid a good inch up the socket (I assume it was oil?). I looked down into the chamber and saw the plug surrounded by the fluid, and now I'm freaking out. Should I have my car towed to the mechanics and have them look at it? I feel like this can't be normal.
View 14 RepliesJust picked up a 2002 F-250 Super Duty. I have a second 110V plug coming out of the grill. The first, on the drivers side, I know is for the block heater through the oil filter housing. The second is attached to a device that is inline of the lower coolant hose. Is this a warming device also?
View 2 Replies