Ford - Ranger :: Stalling When Began Driving / Going Downhill And Coming To A Stop
Jan 14, 2012
My beloved standard, 2000 Ford Ranger, with an estimated 170,000 miles on it, has a problem with stalling that keeps getting worse. 2 different garages have failed to fix this problem three times. Many parts have been replaced/checked (like battery, plugs/wires) and the fuel and induction system was cleaned, fuel pressure, Compression and engine vacuum were all fine. The Check Engine Light goes on and off all the time and does not seem to relate to the problem. When the last garage hooked it up to the computer, nothing related to the problem was identified, they reported. The invoice/report from them is attached to this posting.
My problem began about 2 years ago. The truck would only stall out when I first began driving, after about a mile, and only if I was going downhill and was coming to a stop. Then it would putter and choke and ultimately stall out completely. After my 30 minute commute (near highway speeds) the truck would then be fine the rest of the day, with no problems stalling when I drove to a meeting or out to lunch. Since it began, it has gotten steadily worse. Now, pretty much whenever I decelerate downhill, and come to a halt, it will stall out unless I leave it in neutral and keep fluttering the gas peddle to give it more gas. It even happens when I'm not going downhill. It does not happen when I first start driving, but after a mile or so, it happens almost whenver I come to a stop. It sounds like the truck isn't getting enough gas, and if I don't keep pumping it with signifcantly more gas, it will stall.
Once stalled out, if I try to start it up again immediately, it is VERY hard to make it start. I have to keep turning it over before it finally sparks to life. It sounds pretty awful. otherwise it starts easily. IF, however, I let it stall out in a parking lot at a gas station, for example, and I go into the store and make a couple quick purchases, when I go out to start the truck, it fires right up with no problem. It only has a VERY hard time starting up when I'm in an intersection and try to re-start it immediately after it stalls out.
The two different garages that have failed to fix it were both able to easily replicate the problem, so that was not an issue. Amount of gas in the truck and temperature outside are both irrelevant.
View 3 Replies
Advertisement
I have a 2000 Ford Taurus and when i am going down hill and coming to a stop sign the whole car shakes , the whole front end was redone and yet the problem still persists, It also stalls out when coming to a stop sometimes what could this be ?
View 12 Replies
We have a 2010 Tiguan SEL 4 motion automatic and today it just died after i pulled out of parking spot. the only light on the dash was the battery light. I restarted once i put it in neutral. When driving home my wife and i notice it was not downshifting when going down hill or when coming to a stop. This is not the usual behavior. It also seemed like it was costing in neutral when i was not in the throttle. I dropped it off at my usual dealer and hopefully they can duplicate it.
I am wondering if the battery or alternator is bad and the transmission computer was not getting good voltage and that made it act funny.
View 9 Replies
It's an oldie, 1984, but so far still kicking. 6 cyl 2.8, carb. I took a little couple hundred mile trip a few weeks ago. Rolled back into town no problems.
A few days later I took a ride and the ranger would stall when approaching a stop sign or light. I would hold the pedal down a little to keep it running but it sounded like it wanted to die if I didn't feather the pedal to rev a bit.
I drove a few days later, as I was going down the neighborhood road(25 mph), it acted like it wanted to just die. I mashed the pedal and it had no effect. It didn't stall and eventually I could rev the engine to continue.
It continues to do the same, then will all of a sudden take off like there was never a problem. If/when it does stall again, it can be hard to start until it does start and off I go again like there was never a problem. Other times, it will idle.
Another note: Sometimes when I go to start the engine it will stutter, intermittently turnover. It has done the same thing while actually driving, kind of a jerking deal.
Fuel filter, fuel pump, electrical? I'm going to first check/replace the fuel filter tomorrow.
View 10 Replies
I've recently had problems with my truck running 97 f150 4.2L.The latest episode is it stalling when coming to a stop. It will start right back up, I've checked for codes and found none, I have changed the fuel and air filters and I have tested the fuel pressure.(I have a video of the test however I don't know how to upload it.) Key on engine off it pumps up to 30 immediately on the gauge. key on engine running gauge shows a steady 32. I am really at a loss for what to check next. I really need this truck dependable again ASAP my wife is scared to drive it.
View 11 Replies
I have a 2001 Ford Ranger with stalling problems. Recently I have narrowed the range of possibilities to a fuel delivery problem. The truck has 85,000 miles on it and I had the fuel pump replaced about 10,000 miles ago, the fuel filter was replaced at the same time. The stalling usually happens after it has run for a while and can happen while idling or driving at any speed. . .whenever it lacks fuel. It will restart and run ok for a while after if you leave it alone for a half hour or more. Over the last few months it has happened with greater frequency to the point where I am currently not driving it. I can get it to stall in my driveway by letting it run for ten min. or so. I am getting two computer codes: PO 402 and PO 453.
View 5 Replies
2 questions regarding our 2001 F150 Supercrew. My 2 questions are:
My 2001 Ford F150 Supercrew (5.4L, 230,000 miles)has the check engine light on with the code reader telling me that it is the P0174. The truck would run rough when cold (usually in the mornings) and sometimes it would get close to stalling out when coming to a stop light. So we would quickly put it in park and give it some gas to rev it up a bit. After the truck gets warmed up, it runs great with no hint of the rough idle. Since this all started I have changed out the PCV valve and replaced the PCV hose (including the elbow). I have also replaced the Idle Air Control unit but that didn't really make a difference.
We then experienced a cylinder #4 misfire which we resolved by changing out the cop with a new Motorcraft unit. The misfire went away but we still had the problem of running rough at idle to the point of stalling out at stops when the engine is cold. A few weeks ago we cleaned the MAF sensor and that seemed to work. The truck doesn't run as rough now (when cold) at stop-lights, but occasionally it will still have the loping idle. We cleared the check engine code and it stayed off for about a week before returning.
I don't know what else to check other than trying to see if there is some type of vacuum leak, but I don't have access to a smoke machine nor would I know how or where to hook one up. Removing and cleaning the throttle body would work? What could be causing the trouble, or what I should do to further isolate or troubleshoot the problem? I saw a you-tube video on the F150 intake manifold gasket possibly being the problem and although I hope that isn't the trouble with my truck, if it is then I will have to deal with it. We need the truck to get to work and the car is now due for a registration renewal, but we can't get a California smog certificate with the check engine light on.
View 3 Replies
My wife's 2005 Escape Hybrid has recently started acting up. After a bit of driving at semi-highway speeds (say 10 minutes), when you slow down to a stop- the car stalls out (or what feels like a stall to someone who drives a std transmission car). Sometimes, it comes back on when you turn off & on the car- sometimes it takes a minute of being off to turn back on. After a few cycles of this, the engine temperature warning goes off. After each stall, the car will be ok for a few minutes then stall again when slowing down (it seems to do it when you are under 20mph only- not that I am about to try to stall it at high-speeds). It has circa 70k miles on it, and is obviously in the shop- as it is unsafe to drive. It was a warm day when it first did it (say 80deg), and cooler (50) the next morning.
View 4 Replies
I have owned this 96 k1500 5.7L Vortex Suburban for 3 years.
Problem: Intermittent stalling upon coming to a stop. When it stalls and I try to restart the engine, the starter can barely spin the motor. The timing is thrown so far advanced that it will literally fire the engine backward and grind the starter gear on the flywheel. I have killed about six starters so far. I took it to the dealership and after two weeks they are clueless.
So far we have replaced: TPS, Ignition Module, Cam sensor, Crank sensor, ECM, and perhaps a few other things I don't recall at this time. If it would stall and simply restart, I could cope with it. The only way I have found to get it to start is when it stalls, pop hood, unplug the power source to the ignition coil, turn key and spin engine over for a few seconds, replug the power source to the ignition coil, and attempt a restart. Usually I don't have to do this more than once or twice.
View 1 Replies
Last Thursday I was coming home from work and the first time I came to a stop the R32 began to buck just as I gave it a little gas. Tried stopping and starting it but it continued to do it the rest of the trip home. Fast forward to this morning (first time we've driven it since) and it completely stalled on my wife on her way to work. She managed to get it started and get it home. I drove it around the block and sure enough when it comes to a stop after moving it stalls. I was able to consistently get it to stall just by getting it moving and then coming to a stop. I scanned it for codes last night and got a couple of different codes. Ignore the photo-sensor one - I am fixing that just need to find what I did with it.
Note the address 17 stuff - 2 codes to do with failure of the fuel sending unit. Could this possibly cause the car to stall out?
Also, address 16 (steering wheel) - RossTech seems to think these codes mean a faulty ignition switch.
I've never done data logging before but I was able to capture one of the stalls with VCDS. What columns would be useful to see and troubleshoot?
Here's the link to the log
01-Engine -- Status: OK 0000
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: OK 0000
04-Steering Angle -- Status: OK 0000
08-Auto HVAC -- Status: Malfunction 0010
[Code] ....
View 6 Replies
I have a 2001 Grand Cherokee 4.0L with 215xxx miles. It just started stalling coming up to a stop, but then it starts right up no problem. Engine idles a little rough and the gas mileage has gone down somewhat. The CEL came on a while ago, and the auto shop checked the computer code and said it was the neutral safety switch. I brought this up with a friend who had the same problem and he rebuilt his and said it was easy. So I was going to attempt it, but I can't find the darn thing. @ questions:
1)where is it? and
2)could the NSS be causing the stalling?
View 11 Replies
My car has been stalling out while at stop lights and while driving as well as spuddering and hesitating . i brought it in to the shop twice and both times they said it ran fine . they ran the code and gave me a new oxygen sensor and it still stalled. i brought it to autozone today and they ran the code and camshaft position sensor came up. so i put a new one in and it still is stalling and hesitating to drive. also smells really bad when it kick in. What could be wrong . short circuit or wiring trouble maybe? fuel pump ? crankshaft? electrical problem? spark plugs? cant get a straight answer.
View 8 Replies
I have a problem in the form of a 2000 Buick LeSabre Custom with the GM 3800 series II engine. After 245k miles, it has begun to show it's age in some very unaffectionate ways. It has been stalling, sputtering, hesitating, and unwilling to start at seemingly random intervals. And, such is my luck, there has been no 'check engine' light on at any point during this saga. Here's the chronology of events spanning 6 months:
The first symptom I experienced was occasional sputtering, mainly while going uphill. This began to occur shortly after the spark plugs were replaced during regular maintenance. So I replaced the spark plugs again, and also the wires, fuel filter, and fuel pressure regulator. Plus I gave the MAF a good cleaning.
But the problem persisted, and grew to include intermittent stalling when I would come to a stop. Undaunted, I replaced the ignition coils, and swapped in a used ICM.
The car, obviously displeased with my choice words toward it, began to not start every now and then. It would just crank to no avail. So I would try again after an hour or two and it would immediately start as if nothing was wrong. Fearing that I or my wife could be left stranded I replaced the fuel pump. It continues to stall every once in a while and it still sometimes sputters at low rpms. A lot of times it just wont idle at a constant speed.
So then I replaced the crank sensor and I cleaned the camshaft sensor too. Guess what? It's still intermittently sputtering/hesitating when I accelerate from a stop. And I have noticed that it will also sputter while idling in park as well. It's like it's misfiring, but with no engine codes. I'm not happy.
View 4 Replies
I have an interesting issue that happened today after filling up on the way home from work. I have a 2011 Accent; 5 speed manual with 3900 miles. I filled up my tank and then topped off a little extra (which I now know is a no no) after the pump shut off. I put the cap back on, and after getting a cup of coffee, cranked her up and started on my way home. I drove maybe 20 feet and after coming to a stop, the car stalled. I wasn't sure at this point if maybe I let off the clutch a little too much. I started right back up and drove another 20 feet to a stop sign, and she stalled out on me again.
This time, after starting right back up, I noticed the check engine light was on, and if the car idled, it stalled. This is where it gets a little interesting. I was maybe 5 miles from the dealership where I bought my car. So I made a quick trip to the dealership to see if they could get the codes to determine the problem. After parking at the dealership, I turned off the car, removed the key from the ignition for about 10 seconds, and then started up again for giggles. The check engine light is now gone, and the car doesn't stall when idle. I have an appointment to get my oil changed, and am wondering if the codes can still be pulled?
View 4 Replies
2002 Honda Accord, 4 cyl., will stall unexpectedly when coming to a stop or slowing down. It will start to shake and hesitate as one is slowing down from 35+ mph, then will stall at the stop. Has some trouble restarting, but when it does, everything seems to be fine. No codes are left, and my mechanic suspects dirt or something similar is contacting the fuel injector(s) on a sporadic basis. I did replace the spark plugs as they were due at the time this first showed up, but it has happened twice since in a 3 month period.
View 3 Replies
My Snapper mower has a 11.5 hp B&S OHV engine that was filled with 5W20 oil for storage over the winter to enable me to start it occasionally in the cold weather to keep the fuel system from gumming up. Today I fired it up and decided to cut the yard but after 10 minutes the engine began to smoke and lose power, eventually stalling. The oil level was OK and after leaving it to cool a few minutes I checked the plug and it was loaded with oil so I changed it and the engine started but smoked. I drove it to my shop and adjusted the valves and drained the oil which ran out like water. After filling with HD 30 oil it started on the first pull and I finished mowing the yard, about half an hour, with no problem.
The light oil was apparently too thin for the air cooled engine and B&S does specify 30 weight when the temperature is above 40*. Hopefully there was no damage done to the engine. I will be much more careful about the oil viscosity from now on.
View 19 Replies
My truck is pulsating when I am coming to a stop, a lot of you all said replace the rotors to which i did and new brakes, shocks. Today I went to get my truck all four wheel alignment done to my truck.. something is not right..
I got my driver tire facing straight, look at the left.. I went back to the alignment shop showed them that, they put it back up there, they called me over and pointed out the machine they use say, it is aligned.. So what is the problem you figure?
To update all I've done to the truck in regards to front end..
rack and pinion
upper control arm
upper lower ball joints
stabilizer inks
rotors (front)
brakes
shocks
When I straighten my left wheel, the right does not look right..
View 4 Replies
I have an '02 Tracker and I've noticed if I have several accessories running, that my engine will start to sputter and come to the verge of stalling when I come to a stop. It happens if I have the heat/air and radio or charging my phone on together. What is the cause and/or remedy for this? I've changed the alternator a few yrs. back, but it still continued.
View 2 Replies
I have the problem that my 1996 ranger 4x4 has a break problem. When it comes to a stop it feels like one of the tires locks up, feel wired. Ihad the problem before i changed the front breakpads and it still continues. Air in the lines? ABS module?
View 6 Replies
2001 4.0 4x4 auto trans... Problem, tranny judders when coming to a stop moving at around 3-4mph. Engine drops to around 500rpm and maybe one second later returns to normal as the tranny seems to disengage. No judder or shifting problem when accelerating.
View 5 Replies
A week ago, I bought my wife a 2010 Platnium White Lariat. (I will post pics later, when it's clean). We noticed that the smell of fuel, was bad after driving it, and coming to a stop, say at a stop sign.
We returned it to our dealer, yesterday, and this what they found. Just though I'd pass it on to you, for problem shooting, and infor to ask a dealership.
This is the quote on the paper we have. "Customer states when filling up or at idle the can smell fuel in the passenger compartment. Smells like coming from the engine area. Leaking at fuel rail. Tightened valve and road test no leaks now".
We were told that it was a "schrader valve". There was NO CHARGE for this repair. So far it seems to be o.k.
The advise we were given was as follows:
1) NO HEET is needed in the fuel tank
2) No Sea Foam, or injector cleaner of any kind
REASON: Was told it would mess up gaskets, and seals etc. I'm not a mechanic, just passing the word that I was told.
View 3 Replies
