Ford Ranger / B-Series :: Vibration On Slowing Down
Apr 24, 2012
vibrates on slowing down - no brakes just let off gas - until speed drops down to fairly low. an auto trans. seems to be front end source, the driveshaft and u-joints appear good. I jacked up front and checked tie rods and wheel bearing shake - nothing there?
I haven't found a long enough downhill grade to try it in nuetral selector position at over around 25 mph yet. Could shock absorber do this? They appear good. tires have some miles on them but wheels have the weights on them?
View 14 Replies
Advertisement
I have a 1994 Ford Ranger Supercab with 180,000 miles, 4.0ltr 6cyl and it is in relatively good condition. When I bought the truck the check engine light was on. The previous owner said that it was something in the gas tank that has gone bad but it was not a big deal and the truck could be driven with no problems.
My mechanics have tried several times to read the error code but their diagnostic tool won't tell them what is wrong.
I have noticed over the past few days that when I am slowing down and riding the clutch (I was making a u-turn this morning) that the truck will shut off. It starts right back up but it keeps happening.
I have been considering replacing the IAC, new spark plugs, rotor and wires and fuel filter but I am not 100% this will fix my problem. I am NOT a mechanic but know plenty of them so it will be a situation where I buy the parts and a buddy puts them in.
View 9 Replies
I just totally re-built the rear brakes in my 93 Ranger 2wd. Now its seems I have this 'intermittent vibration' between 90 to 105 km/h.
View 7 Replies
We have a 2000 ranger 2wd with a 5 speed transmission, we just had new tires put on last Sunday and on the way home it had a vibration in 5th gear at 55 mph whats so strange about it is, in 4th gear at 55 mph. it don't do it but when you shift it to 5th and hold it at 55 it starts.
I have checked the drive shaft and even put it on stands and shifted through the gears and held it at 55 no vibration, I guess because there is no load on the drive train. the truck only has 56,000 miles on it.
View 9 Replies
he has a 2009 ford Ranger, 2.3L .with 54thou miles, the Issue is Vibration during in gear and stopped at a light no vibration at higher rpms during driveing, he states vibration happens in park ,neutral,reverse and drive. had the truck in for repair in two separete dealers they couldent find the problem its an automatic trans. he states from day 1 this truck has had the prob now its out of warrentee.dealer told him that trans to engine alignment was the prob dealer did some alignment and worked for a few weeks.
View 10 Replies
I'm having a bit of an issue with my 97 ranger 4.0 auto 2wd. I have an vibration which from a stop up about 10 mph feels like wheel hop not bad but you can definitely feel it it and over 50 mph the whole truck starts to shake again not bad but you know its there. the truck sat last summer it was my dd till a bought a new car and now vw is buying it back ill be driving the ranger in the mean time. I have been trying figure it out for a few months but no luck i have put new tires , front rotors and rear drums , drive shaft support bearing ( 2 pc shaft) new u-joints and a used boneyard shaft with new u-joints as well, checked the tail shaft bushing which had about .008" of play.
Pulled the drums Off today and checked the axle bearing for play only .004" of play pulled the diff cover and checked for carrier play as well as pinion play but can't find anything. I'm at a loss here and looking for other things to check ... Don't know if its possible that something in the transmission is loose it was rebuilt about 75k miles ago I was going to stop and talk to the trans shop to see what he thought (its a 5r55e ) ....
View 14 Replies
In my 2006 Ranger XLT, 4.0L V6, 2WD Manual; I am getting vibration from what appears to be the passenger front. I have so far replaced the front wheel bearings (both sides), replaced front shocks and checked rear shocks, rotated tires (to see if it changed) and had front tires balanced. I've also had a friend follow me on the freeway and check the wheel to see if is bouncing, wheel appears to be glued to the road. I have done all the front suspension checks I can and find no indications it is the lower ball joints or tie-rod ends.
This vibration is very in consistant, in different lanes it is better/worse. At times I feel it more in the steering wheel, others my seat and at times the gear shift. I don't believe it to be the engine mount(s) cause when it is vibrating I can shift into netural and the vibration does not change, I have also performed the 5K rev (FORD maitn. manual) and the engine is smooth (along with my expierence with bad mounts in my '94).
View 11 Replies
Bought a 02 Ranger, 4.0 4x4 super cab 122,000 miles. etc Picked it up for 500 bucks because someone scrapped it along the side of a guardrail this last winter. Replaced rack and Pinion (cracked), Tie rods, Shocks, driver side knuckle and wheel bearing, and some body issues (bed is still shot so if any black short bed sitting around let me know). I've been kind of putting around all day in it, letting it used to working again. Starts right up, turns easily, I string aligned it so it goes where I want.
But as I get up to speed start at about 10MPG there is a vibration based noise coming from the front, can't pin down if its left or right. If Im going straight then turn it gets slightly more intense as I even start turning the steering wheel. The noise increases with vehicle speed. And I don't know if its separate or related, but any turn over 5-10* to the left results in a grinding sound but then I turn to about 10-15 and it gets less intense. No noise turning right.
I'm thinking a bad CV, TWO bad CVs, or a bad differential. Before I start ripping into those things, thought I'd get opinions, or hopefully experience in this area. I'm really hoping its something small and stupid. (like not getting a professional alignment)
View 6 Replies
I recently replaced the oil seal on the front differential where the front drive shaft connects to the diff. I believe it is called the pinion oil seal. I had to remove the drive shaft to do the job. Got the oil seal in place and then slipped the u-joint yoke on and hand threaded the retainer nut on to get it started. I did mark the relative position of the drive shaft to the front yoke and the rear yoke. I had previously noted that the retaining nut, before I took it off had about 2.5 threads showing. I had to remove it with an impact wrench.
So...I used the impact wrench to put it back on with about the same number of threads showing. I then reinstalled the little short fronmt drive shaft...the one that comes out of the transfer case. I got the front of it on to the pinion output on the front diff...and then had to reattach it to the transfer case end which, by the way an interesting affair with a sort of metal cone that is attached by 6 8mm fine threaded bolts about 2.5 or 3 inches long. Got all that done with much grunting an groaning - I'm laying on the ground - SO the oil, leak is fixed but now ...
There is a vibration at around 40 mph and higher. like something is out of balance. did i damage the front diff pinion bearing by using an impact wrench? this vibration occurs in 2 wheel drive. as i understand it the front drive shaft doesn't even turn when in 2 wheel drive. my question is does the front diff gears spin when in 2 wheel drive? perhaps the u-joint is bad on the front drive shaft? just a bit baffled. when the speed drops to below 40mph the vibration goes away...
View 2 Replies
As said vibration at idle, as I slowly accelerate (in park) the vibration is worse at 1200 rpm, then keep slowly accelerating and at 1800 rpm completely goes away. Doesn't seem like a miss almost like a balance thing. Also when in gear and accelerating it doesn't seem to be there unless I just don't feel it when moving.
View 5 Replies
Have a 99, ext cab, 3.0 , 5 spd man. 125,000 on it. I know the clutch will need replaced shortly but so far it is still functioning with out the slipping. Although I can feel a slight vibration, or buzz when I up shift. My immediate concern is the clattering/rattling. say at idle, not moving with the clutch pushed in when I shift into 2nd and 4th gear it really rattles loud. I can only assume it is some bearing inside the transmission, but need to have a bit more surety as to the problem. I know, I need to do the clutch however i don't know if the transmission is going bad or is that noise in the clutch area.
View 2 Replies
1999 Ranger xlt, 4 cyl. 2wd reg cab, automatic. Getting a rumbling noise with some vibration in the floor ( nothing in the steering wheel, does not seem to affect handling ) runs consistently and relative to speed of vehicle......can not isolate or determine origin of noise.........
When initially driving car after sitting for awhile, the noise does not kick in until 50 to 100 yards have been traveled but is consistent thereafter,.....except for.. completely disappears during taking of left handed curves at good speed but reappears when road straightens...... right-hand turns have no affect positive or negative.
Have thrown into neutral at speed and sound and vibration is unaffected,.... brand new tires ( needed them ) with balancing had no affect either Struts, shocks, springs?
View 4 Replies
I have a 98 ranger, 4x4, 5spd 3.0 with 88k miles.
While I am driving it, everything is great, but when i start to accelerate, or torque the engine (going up a hill), I get this clicking/vibration in my gas pedal. its extremely noticeable, by feeling and ear.
Its most common around 2k to 2.5k RPM. There is a lot of play in the throttle cable, about an 1" or so give untill you feel pressure. What I need to replace or tighten?
View 1 Replies
i have a 2010 with 182k miles. The vehicle will jerk like the drive is engaging and disengaging several times (repeatively) when going down hill. It doesn't matter how fast, but I notice it does depend on the ECO indicator. The ECO gage always indicates above the mid mark but ranges between no more than quarter to an inch and quarter above. If I speed up it stops and if I slow down below the mid line it will stop.
View 13 Replies
I own a 1992 Volvo 740 wagon, non-turbo. Super solid car up until a month ago when it developed a grinding sound and vibration when slowing down from 15-0 mph. There is no noise or pulsating at any other speed when I apply the brakes. This happens with tranny in N or D. I replaced the front rotors and pads about a month before this started happening.
I suspected the rear brakes so I also replaced the rotors and pads but I was still getting that grinding/ vibration. The next thing was to replace the hub/bearing assembly, I only did the drivers side because I banged it up pretty bad when replacing the rotors. This also had no effect on the grinding. I also noticed that when driving at moderate to fast speed I hear a humming noise, almost like big truck tires make. This is especially noticeable when letting off the gas and coasting. Could this be a tranny issue?
View 3 Replies
Change rotors , pads and calipers and I still get a vibration when I hit the brakes slowing down on the highway.
View 19 Replies
Wanted to query the collective wisdom here: last few days, been getting a strong grinding/vibration rolling along, but only under steady speed or slowing down. Early in any trip its barely noticeable, but after an hour on the highway it can resonate pretty strongly. Gets worse with speed. Goes away completely under acceleration.
Doesn't get better or worse with brake application, stays exactly the same if I pop the tranny into neutral and roll along.
2008 B6 Sedan (trendline in Canada) - 103000 km (roughly 60000 miles)
Couple of possibly related observations: tires are down to their last 1/3 of life (but fairly even wear across all 4), brakes do need attention (bit of a pulse on application), and when I was switching from snows to summers I noticed a small splash of grease on the driver side CV boot - couldn't see a split but I don't think it should have been there.
My thoughts: possibly CV joint going, or really need new rotors...
View 5 Replies
Here's the deal:
1. My 2002 SC430 with 23,000 miles on it is making a low rubbing noise when slowing down, with a slight vibration, not severe enough, but it is annoying and frankly surprising on this car. The dealer tells me it's because the brakes have "glaze" on them, and short of a new brake job, you can jam on the brakes to clear or loosen some of this and reduce the noise. ( I live in the desert so I'm sure I could find a deserted stretch or road for this craziness...) The dealer reports the brakes have 70 - 80 percent life on them and I don't need a brake job.
2. Power steering. I thought this particular car was just hard to steer, but even the tech at the dealer commented it's like I have no power steering. I test drove two other cars, and the steering is markedly lighter on the other two SC430's I drove. (2002 and 2005) Dealer can't seem to find an explanation, but I have to drive this car with two hands around town... I know this is not the way this car was intended to feel.
I don't believe the car changed that much from the 2002 model so as to affect the steering. BTW, I'm using stock tires, not run flat, 4 months old. And the steering is stiff at idle anyway, regardless of tires. The first SC I drove, which sealed the decision to buy one, was so quiet I didn't know the engine was running, easy to steer, and smooth.
View 6 Replies
I have a 2004 Honda Accord EX (4 cyl) with 102k miles. I bought it brand new and kept it completely in shape with regular service. For the past few months I start getting front end vibration at braking, mostly when slowing from high speeds and without any repair this vibration has now became common at all speed.... my diagnosis - I need to replace to turn disk/rotors....
While I have not remedy the rotor issue yet, I started getting this new vibration at 60 to 80 mph.... Below and above this range of speed i have no vibrations - the car will drive fine. This type of vibration in my experience for front wheel drives is mostly due to balancing or bad tires. so i took the easy way ..... and as i already needed tires well i dished out the dough and replaced all four with Michelin Primacy hoping that it will resolve the speed related vibration.... Well it did not?
I continue to drive as-is without addressing the real problem - coz I'm not sure what is causing the vibration.... now new additional vibration started on acceleration; any time I hit the gas pedal (normal acceleration or kick-down) I get vibration very similar to when a stick shift's gearbox required replacement/repair of the worn out pressure plate's (fingers/springs gets bent or weak) or the thrust bearing needs replacements/repair/grease packing. I'm from the old school stickshift transmission, my knowledge in automatic is very little - I have repaired Acura's automatic transmission before but I don't think repairing once will make me an expert in automatic.
So to summarize my issues or current state:
Issue# 1 front end vibration on braking
Issue# 2 front end vibration 60 to 80 mph speed only
Issue# 3 front end vibration on acceleration at all speed
The list above is in sequential order as I have experienced.
View 9 Replies
I just changed my Oil, added a FRAM filter and bought some good Quakerstate High Mileage and my truck runs good. However, I noticed that my Check Oil light is constantly on. I also recently changed my Oil Sender, and I wonder if that has got something to do with it.
View 3 Replies
I have a 1994 2.3l 4cylinder xlt ford ranger regular cab Manuel transmission. My transmission is going out. I found an 04 ford ranger Manuel transmission off a v6 will this be compatible? And if not what years will be?
View 2 Replies
