Ford Ranger / B-Series :: Uneven Front Brake Wear / Caliper Sticking Slightly
Dec 26, 2015
2000 Ranger, see my sig.
Just had to swap out the pads on my truck yesterday. The pedal was pretty mushy and I was getting shaking in the steering wheel when the brakes got warm. Shaking wasn't all the time, only after they had been used quite a bit - say after city use and the brakes had to be applied suddenly. So I popped off the tires and swapped out the pads and replaced the brake fluid - flushed it.
On the driver side front, the pads barely had any real wear and the anti-rattle clip was all messed up. It was installed properly, but it looked like the pads had smashed into it. The rotor appeared to be warped, or at least out of round - but just barely. You could see it wobble slightly in one spot if you spun the hub with the caliper removed. The caliper itself was sticking slightly.
I didn't see any evidence of damage, the brakes flushed just fine although the fluid was incredibly dirty (because I haven't done it in a long while). On the passenger side front, the pads were worn down to the level I would have expected given the mileage. The wear was even.
My question ultimately is this - is the out of round hub the culprit here? Might there be something else going on like a caliper problem? Ultimately I plan on having the rotors surfaced - one of them certainly needs it and with new pads I might as well do it anyway.
View 5 Replies
Advertisement
Yesterday, I noticed that my right front brake caliper seemed to be sticking. This morning I jacked up the front end, and could barely turn the right front wheel when it was off the ground. So, I have concluded that that caliper is sticking. So, here is the question(s): what is the best way to repair this (new caliper, rebuilt caliper, or rebuild it myself), do I need to do both sides the same or can I just do the one that is acting up, and should I expect to pay. I have some mechanical ability, but that Haynes manual doesn't make too much sense to me. Getting it professionally repaired is extremely inconvenient, I need to be back at school (300 miles away) Tuesday evening, and probably couldn't get it in to get it done before then.
View 12 Replies
I have a 1999 Ford Ranger XLT using the Futura GLS 225/70/R15 tires. The vehicle decal in the driver side door listed the recommended tire pressure to be 30 PSI. I have tried to maintain religiously along with proper balance and alignment. However, I've always had the experience of the tires wearing out more along the middle which seemed to indicate over inflation. The sections on either side of the center line seemed to wear out normally. For this reason I've had to turn in the tire prematurely as they become unsafe. These tires were made by Coopers Tire and distributed by Pep Boys. Have i been using poor quality tires all along? Do I need to lower my tire pressure below the 30 PSI recommended? If I do that wouldn't I be risking overheating and/or affecting my gas mileage?
View 13 Replies
98 Ranger Front brake lines Too short! they kink in sharp turns and wear out then start to seep then eventually leak and need replacement. Checked parts references and the lines have been considered stock. Not sure if I have a 1/2 year model.
View 1 Replies
I noticed this yesterday when swapping out my wheels. What could be the causes?
Pass side
Drivers side
View 24 Replies
I checked my pads today and noticed that the drivers pad is worn about 50% more than the passenger in the front. What could be the problem??
View 5 Replies
I know this has been talked about many times and how to solve the issue but thought I would ask some other questions too. Earlier in the summer, I did grease the slider pins as preventative maintenance. I don't drive my truck all that much and when I used it yesterday, (about 30 minute drive) I came home to burning brake smell. I'm wondering if enough heat would cause the caliper to go bad? Should I just grease the pins again or change out some parts?
View 6 Replies
One of the pistons in my driver side (UK) front brake caliper is sticking, so I've bought a second hand caliper just to fix the problem until I come to sell my pri in a month or so.
View 15 Replies
2005 Toyota Solara my front driver side caliper was sticking and heating up a couple months ago... replaced the caliper and the rotor... still had the same problem. I would drive it, it got hot and stuck, after I parked for a little while it slowly released. Talked to a couple of mechanics and they both said undoubtedly I had a bad flex hose and it was collapsing with pressure and then will release... I changed the flex hose and flushed the fluid and it was immediately fixed...no problems.
Drove the car for a month, went to South Carolina and back and then a couple days ago the same thing started happening. Talked to a mechanic, he told me that the new caliper may have gotten fried from over heating before I changed the flex hose... Got a new caliper today (warranty) exchange... changed it out and still have the same problem. When it sticks I can release the pressure by opening the bleeder valve so it seems like the flex hose issue again... my only thought now is maybe the new flex hose is a bad one and someone mentioned the proportioning valve.
View 9 Replies
97 4.0 ext. As the title says the right front pads wear more than the drivers side. Have replaced calipers pads and rotors during recent overhaul. Noticed increased brake dust on wheel on rf front. Could the metering valve under master cyl be the culprit. Abs and brake lights work as normal.
View 4 Replies
My '02 Ranger has had tire wear for a while now, and its on the inside of both front tires. I was thinking it was either toe or camber, or maybe both. I havent been able to get an alignment recently. If its the camber, should I get the camber kit from Ford?
As for the squeaking, it first happened last summer, and I sprayed WD-40 on the upper control arm bushing and it went away until last week (obvoiusly temporary). Now its back. Also happens while turning the front wheels.
View 10 Replies
My son and I were doing a transmission flush and while we had it on the lift, I noticed the oil pan gasket was sticking out in the front quite a ways. I assume its time for a new one. Is there anything I need to know having never dropped the pan on this truck? Is this a common issue?
View 14 Replies
My left brake caliper locks up on me. I have replace it, the brakes , and the wheel bearings. when im driving down the highway and go between 45 -55 my front end shakes really bad and i start to lose power.
View 8 Replies
My 99 ranger has just hit 111,000 miles. I'm getting a weird sound from the front right whenever I turn the truck slightly to the right. I don't hear it if it's leaning left. Is this likely the wheel bearing? I've heard these rangers are not best known for the quality of the wheel bearings.
View 14 Replies
2005 I4 SE Camry USA built. Got a squeak from the rears the other day and pulled the tires to check. Inside pads (ones against the caliper cylinder) on both rear wheels were at the metal but the outside pads were still not down to the little stripe down the middle of the pads, let alone the wear indicator clip. I pulled slide pins and there were not stuck. The calipers retracted very easily, so not gunked up or dragging. I ordered a new hardware kit with the new dust boots and rubber slide pin parts. I am using good Permatex disc brake grease. I am going to have to have the rotors turned, but aside from replacing the rubber parts the only other thing I can think of is slide pin replacement.
View 2 Replies
I just thought I'd mention this observed wear of brake pads...I just replaced all 4 up front after about 128k miles...
@ 114k miles it was observed that 1 of the 2 pads of each front wheel had worn significantly more than the other (the inner more than the outer pad IIRC)....my expert mechanic rotated the two and I got another 14k miles out of them...I could have gotten a LOT more had they been rotated @ 50-80k miles.
I don't know if this is extraordinary, or more typical than I'd have thought...or a function of (failing?) calipers, or just how these (MY) calipers work, or just my driving habits (though I've owned the car for only 30k of the 128k miles on the odometer)....but....
In my case the new pads will get a 50k mile inspection and possible rotation if there is uneven wear between outer and inner pads....
I'd recommend that pads be inspected for (uneven) wear at one of the scheduled tire rotations....rotating the pads isn't much of a job, but it might be something for you to consider to get the most miles from the pads (that and better braking too perhaps).
View 14 Replies
Have 50,000 mile on my 2011 F350 6.7 and up until today the truck has been flawless. This is my weekend vehicle and sees very light duty hauling fishing gear to my boat (100 miles hwy) and pulling my 7x12 enclose trailer with goose decoys. On a couple of occasions pulling my 29 CC from marina to my home and back. Took truck in for oil change and tire rotation, service advisor informs me I have 2mm on rear brakes and 3mm on fronts. Not sure why rears have more wear than fronts. Schedule to have brakes done for today and now find out that front right caliper is sticky and they want to replace both front calipers. I cannot believe that a 2011 SD F350 with 50,000 miles and of that mostly highway needs brakes let a lone calipers are going bad. Service manger tried to tell me that brake fluid should be replaced every 2 years, to which I responded that I have Ford perform all scheduled maintenance. He went on to say that this is not scheduled maintenance, wtf bs is he telling me, if it is necessary then it would be scheduled maintenance. Truck gave zero indication of stuck caliper, no sound and no excessive brake dust on wheel.
View 14 Replies
I just hit a pothole on my way home just now and now my front right caliper is sticking. It happen about 10min from my house. As soon as i hit the pothole I can feel my truck pulling to the right and felt like there was some resistance when i was driving. I got home and peeked my head in the wheel-well and i can smell the brakes burning and smoking a little. How would hitting a pothole cause a caliper to stick. Is there anyway to unstick it or am i gonna have to change that caliper out...
View 8 Replies
I recently bought a 2006 Ranger with supposedly 110000 miles... I don't think I made a good deal... because I found the stabilizer end link in terrible shape which seems suspicious for this mileage in my personal opinion!? But this isn't the reason I am posting today... I have a serious breaking issue and I couldn't find explanation yet.
My ABS Light is on. When I slowly brake at low speed and when the brake is almost completely depressed... I hear a low humming sound, and the brake pedal seems to momentarily drop back just slightly. This also happens when I'm going down hill and breaking. For the most part, the car breaks, and it's only every 8th or 10th time braking that I experience this issue.
My guess is this is linked to the ABS... but I can't afford expensive service and need to resolve this on my own.
View 2 Replies
Any 1 have their tire that have uneven tire wear? Mines is Dunlop and my front right tire has uneven wear on the outer thread. All other tire don't have uneven wear. I'm getting new tire for all 4 rims and check my alignment. My gs is a f sport rwd.
View 3 Replies
I heard a grinding noise coming from the right front tire last night. Came home, removed the wheel / tire and noticed the caliper was stuck pushing the pads against the rotor. I pushed the caliper pistons back in so they're not frozen, just sticking.
View 14 Replies
