Ford Ranger / B-Series :: Truck Won't Start In Cold / Security System Light Comes On
Nov 16, 2014
We have a 2007 Ranger. When the temps hit 32 degrees F or below, the truck won't start. The security system light comes on. We have to run through the security system reset process, sometimes a few times, before it will start. Afraid all this key turning is going to burn out the ignition. Don't have a lot of confidence in my Ford dealer as they replaced the brakes and put the shims in wrong. Local mechanic says it's probably electrical. Is there anyway to bypass the security system or can it be removed?
View 1 Replies
Advertisement
Removing fuel injectors-coolant contamination.. How is this done? I need to see if they are any good-or clean/replace them-after I accidentally left the clip off the hose running out of the thermostat housing when I drained my coolant last week and the first time I drove, coolant leaked onto the top of the engine/manifold depressions, getting onto and into the fuel injectors.
I tried to clean it up as much as possible the first time(finally got it going) but still a few days later the truck at times cranks but does not start-hot or cold. I assume my idiocy is the cause or maybe it is just coincidence of something else? From what I read from my symptoms it could also be the fuel pump relay, pressure regulator, coolant temp sensor, crank sensor.. among other things. My fuel pump is 1.5 years old, so hopefully that isnt it. Have the injectors possibly been contaminated to where I should just replace them?
View 14 Replies
My 1990 4.0 refuses to start when the air temperature outside is at approx 40 degrees or below. It will crank until the battery runs dead if I let it. At approx 50 degrees farenheit the truck takes forever to start and always backfires out of the tailpipe and intake manifold (blowing off a hose on the vacuum tree) before it starts. If I can get it to backfire, it will start eventually. If it does not backfire, then I can run the battery dead and the truck still refuses to start. This condition has grown from a little problem to a huge problem over the past 6 months. Here is what I have done so far, including regular maintenance items.......
KOEO test checked OK
KOER test returned code 77 multiple times (TPS).
Replaced Throttle pos. sensor
Replace Idle air bypass valve
Subsequent KOER test came back with no more codes except 11 - OK
Load tested battery
Made new heavy gauge battery cables for + and -
New plugs, wires
newer starter
Changed coil pack for known good one off my explorer
Visually inspected hoses for vacuum leaks, replaced 1 cracked hose
1990 Ranger ext cab 4X2 4.0L, K&N air filter in stock airbox, Pacesetter headers, single 2 1/2" exhaust, stock cat no muffler, 260K on truck, 104K on good used engine from my 1994 Explorer. Purchased Ranger brand new in 1990. A4LD w/ shift kit.
View 14 Replies
I just bought a 2000 Ranger. I bought it at company auction for cheap because it wouldn't start. The battery was dead when I got to it. I put a brand new battery in it since it has 155,000 miles. When you turn the key to the on position, the theft light starts blinking rapidly. It will continue to do so for about 45 seconds if you leave the key on; then it will go out. However, if you turn the key to start, all you hear is relays clicking. The engine doesn't crank at all. I jumped the starter relay and the engine turns over. I have the factory manuals for wiring diagrams and diagnostic procedures.
The theft system relies on trouble codes to point you in the right direction for testing. I borrowed an Actron code reader (like you get at Autozone) and it says there are no codes. I'm wondering, though, if it only reads the SAE standard codes from any vehicle and not the manufacturer specific codes like the theft system. I have gone through a few of the diagnostic procedures with a multimeter, but it's like looking for a needle in a haystack without the codes. So far everything I've checked has come back ok. Any common issues this might be related to? BTW, I've gotten bits and pieces of info about this truck from the guys who drove it. Apparently, it just wouldn't start one day and was parked for the next several months until I bought it.
View 14 Replies
Sometimes the check engine light comes on and truck will not start, the fuel pump runs non-stop.. when check engine light goes off,the fuel pump runs for a few seconds and stops,truck will start.... driving down the road check engine light will come on and truck runs bad.... 1993 ford ranger .....
View 1 Replies
Sometimes the check engine light comes on and truck will not start,the fuel pump runs non-stop.. when check engine light goes off,the fuel pump runs for a few seconds and stops,truck will start.... driving down the road check engine light will come on and truck runs bad....
View 2 Replies
I have a 2000 Chevy silverado. I recently was having problems with the transmittion not switching correctly. Long story short the shop told me to fix the problem I had to put in
A new transmition as well as a new computer which I did, from another Chevy. It worked for a few days then The truck was not starting and had security light on. Had alarm specialist take look and he said the computer had to be reprogrammed. It was reprogrammed at merles. And was still not working. Its unable to start, starts at random once in a long while. ignition switch was changed and still gave same problem. Took to another shop they had a specialist take a look and he said the computer had to be reprogrammed again.
Also would it be possible to bypass the anti theft system by adding a remote start, or cutting some wires. I just really need to get this truck running.
View 14 Replies
I have a 95 Ranger with the 2.3L and it is a five speed. I am having a starting issue. I have replaced the ignition switch, clutch position switch, starter relay and had the starter tested. The truck will not start with the key. I can jump across the relay and it starts fine but will not even click with the key.
View 3 Replies
I had my battery out for quite some time. When I put in a brand new battery my key was not recognized and my truck will not start.
View 3 Replies
I have a 2002 Ford Ranger, and it wont start at all. Ive replaced the starter, had the battery checked. Not the battery, took starter out, had it checked too, its not the starter either. Someone said it maybe a fuse? This is totally frustrating, and I need to get it figured and fixed asap. Its been going on for weeks., I had it fixed and then it just stopped. It wont even take a jump anymore.
View 4 Replies
I have a 96 ranger 4.0L shift lever was very sloppy and one of the torq bolt fell on the floor I used loc tite and tightened them up with no problem put everything back together and now it wont start. I think I checked everything even replaced the neutral safety switch, adjusted the tranny cable, checked fuses and switched around the relays maybe an ignition switch? I am running out of stuff to troubleshoot.
View 13 Replies
My 03 Ranger 4.0L has become a mystery that has baffled every one I know. Everything was fine and I ran home to something from my house was in there maybe 10 minutes came out and the truck wouldn't start. it doesn't even crank over. out of the clear blue. I had a friend who works for a garage check it and he thinks timing chain. Since then I have been told it wouldn't just fall off sitting there with no indication at all there was a problem.
Thought maybe PATS system. Its in order. Put in on a computer from auto-zone and it shows a check engine light but the reading is there is no codes in the computer on file. I am at a loss. Its been months and I really cant afford to take it to a garage right now. Its the strangest thing ever no crank, no stalling just nothing I hit the switch it lights up like its ready to start and nada.
View 3 Replies
I have a 95 Ford Ranger 2.3L with a five speed. I recently had a starting issue were I parked the truck, went into a store came back out and the truck wouldn't start. Figured it was the solenoid as I couldn't jump across it to get the truck to start. Replaced the solenoid. Still no go. Found a fuse in the starting circuit blown. Replaced the fuse and got it started and drove home. Next morning, I go to leave for work and the truck would not start. Got a ride to work came home and checked it over and found the starter locked up. I replaced the starter. Truck started for a few days and now I am having problems again.
Here is the problem I am having now. Starter is good. Proved that as I can start the truck by jumping across the starter relay. Checked the solenoid with a voltmeter and it is doing what it is supposed to do when the truck starts normal. Here is where I am scratching my head. I can start the truck sometimes and it starts just fine. Next time I try to start it, the fuse will blow.
Replace the fuse and it might work for a couple of starts and then the fuse will blow again. I jumped pass the fuse with a piece of wire for diagnostic purposes. Out of 20 starts, it only started normally 4 or 5 times. I have checked every wire I can see under the dash and have not found any obvious issues. I am at a point where I am so frustrated that I just want to push this 400k mile truck into the back forty and put it out of its misery like a lame horse.
View 9 Replies
I have a 91 Ranger 4cyl. Tune up about 2 months ago. Mileage about 178,000. When the temperature gets below about 45 degrees, the truck will not start. It cranks like the battery has plenty of juice but refuses to start. Once the temp warms up, the truck will start first crank.
View 5 Replies
Installed a new clutch and slave today. Kept the same master cylinder.
The problem I am having is that the clutch pedal will not go to the floor, and therefore the truck won't start. The slave is moving back and forth roughly 3/8 inch, maybe more. I am pretty confident that there is no air in the system.
If I loosen the pressure plate a little, the clutch will go to the floor. But tighten it back up, and it again only goes down about 75%. This is a late '95 so it has the self adjusting clutch. I did get the correct kit for it, as well as slave. It's like the self adjusting part is too far adjusted and won't let my slave travel as far as needed.
In troubleshooting, I did notice that I failed to get the dowels in the flywheel aligned in the pressure plate. I am old school and not used to dowels in the flywheel! The dowels are not hitting anything and are not preventing the pressure plate from seating on the flywheel. But it is something I'm going to fix if I have to pull the trans again.
For reference, I replaced the clutch because the slave cylinder was hanging up and preventing the clutch from getting fully released. Aka clutch slipping.
View 6 Replies
I have a ford ranger 1996 4 cylinder. The truck was driving fine then all of the sudden it shut off and wouldn't start... I checked spark and that is fine also changed fuel pump and made no difference. We also sprayed lighter fluid and that did nothing. It sounds like it wants to start but wont.
View 10 Replies
The truck just won't turn over makes a rrrgh rrrgh noice like it wants to start, I push the gas peddle to the floor and I should smell a lot of gas but don't!!! I added oil when it died at the store last night and it started up but the oil stick indicates oil is fine??? Pulled the diode out this morning put it back in the truck would not start just made that noise but turned it off and reseated the diode and it started??? These things may or may not have anything to do with the problem. Could it be electrical or oil pressure gauge sticking or something else that I could tell my mechanic and he could fix so I don't get stuck????
View 14 Replies
This has happened 3 times.
1st) pulled quickly over to side of road, shut off truck. It would not start then. Towed it to service station and it started the next morning (with no repair made). I wonder if tow ride dislodged the the blockage in fuel line(?). Always sounds like it's going to turn over, but like not getting fuel.
2nd) Went to leave work, truck wouldn't start. Towed to my mechanic and he replaced fuel pump. Thought it was fixed because it ran fine until just the other day.
3rd) Slowed down to complete stop in heavy traffic and it stalled. Would not restart. Again sounded like it was going to start but didn't seem to be getting fuel. Good samaratins pushed me off road. Had it towed to mechanic. Started the next morning without any repair or service. It's like the tow ride and bumps getting it off the tow truck dislodges what ever is blocking the fuel line.
My mechanic replaced the fuel pump, but I don't think her replaced the fuel filter.
View 6 Replies
I've got an 87 ford ranger 4x4. The truck won't start. The ignition is firing off with the key on engine off. When I got the truck the transfer case was blown. The people I got the truck from drove it to here it sat. I check the wiring but the transfer case to make sure it diet get damaged causing a sort. When I got the pcm was missing. Took one out of a bronco 2 and changed the relays on the fender. Here what I've done so far
Relays
Pcm
Complete tune up.
Distributor and ignition module
Replaced and repair some grounds.
View 1 Replies
I have a '96 Ranger XLT. Just recently the dome light stays on while the truck is running. I have checked both doors and door frames. For the life of me I do not see a switch. The light does go off eventually after the truck is shut off (without killing the battery). What or where is the switch for this light..
View 14 Replies
Specs: 2003 Ranger Edge / 3.0 V6 / 5-speed 4WD / 238,000 miles
Yesterday my truck was in the shop for repair. Intake gasket, Transmission fluid change, all heater hoses, thermostat, serp belt and coolant flush. When I picked it up from the shop, which was after closing, I noticed a knocking on start up. From past experience on a different truck, it sounds like a cam that isn't oiling. After a few minutes the knock goes away. I drove for a few miles, turned off the engine and started it back up and no knock this time. This morning I started it, knock was back but went away after a few minutes. Oil was changed about 1500 miles ago. Running pennzoil 5/20 with a K&N filter. Up until yesterday the engine has been completely quiet. Was wonder if something may have clogged the filter or the drain back valve.
View 6 Replies
